1. don't let go back using goto.
2. don't call skb_act_clone() until it is necessary.
3. one exit of the critical context.
Signed-off-by: NChangli Gao <xiaosuo@gmail.com>
Signed-off-by: NJamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reported-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: NRémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes config dependency on x86 to build vmxnet3 driver. Thus
the driver can be built on big endian architectures now. Although vmxnet3
is not supported on VMs other than x86 architecture, all this code goes in
to ensure correctness. If the code is not dependent on x86, it should not
assume little endian architecture in any of its operations.
Signed-off-by: NShreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The netlink URELEASE notifier doesn't notify for
sockets that have been used to receive multicast
but it should be called for such sockets as well
since they might _also_ be used for sending and
not solely for receiving multicast. We will need
that for nl80211 (generic netlink sockets) in the
future.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Put Tx and Rx DPC to be handled in the NAPI:
  - Saves status blocks.
  - Moves the Tx work from hardIRQ to NAPI.
Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. This patch is based on the kernel of 2.6.32-rc7 

2. In this patch, we enlarge the out buffer size to optimize the
   upload speed for the ppp connection. Then it can support the upload of
   HSUPA data cards.
Signed-off-by: Nfangxiaozhi <huananhu@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- move Kconfig entries to the subdirectory
- do remaining renames of mpc52xx to mpc5xxx
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Not all hardcoded values have been replaced as this made the code quite
unreadable. IMHO this compromise serves the purpose of readability.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: devicetree-discuss@ozlabs.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge two functions into one. The result is smaller as they can now share some
variables.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As suggested by Wolfgang Grandegger.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- use extern where apropriate
- don't export symbols
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The upper layer does not support it yet.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- remove whitespaces
- use ! and ?: when apropriate
- make braces consistent
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/can/Kconfig

ks8695_rx() will call refill_buffers() for every incoming packet.
Its not necessary. We just need do it after finishing receiving thing.
And the 'RX dma engine' is in the same situation.
This blocks our user space application. The following patch may fix it.
Signed-off-by: Nzeal <zealcook@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ks8695 rx irq is edge-level. Before arriving at irq handler, the
corresponding status bit has been clear(irq's ack).
So we should not check it after that.
Signed-off-by: Nzeal <zealcook@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PPP does not correctly call pskb_may_pull() on all necessary receive paths
before reading the PPP protocol, thus causing PPP to report seemingly
random 'unsupported protocols' and eventually trigger BUG_ON(skb->len <
skb->data_len) in skb_pull_rcsum() when receiving multilink protocol in
non-linear skbs.

ppp_receive_nonmp_frame() does not call pskb_may_pull() before reading the
protocol number.  For the non-mp receive path this is not a problem, as
this check is done in ppp_receive_frame().  For the mp receive path,
ppp_mp_reconstruct() usually copies the data into a new linear skb.
However, in the case where the frame is made up of a single mp fragment,
the mp header is pulled and the existing skb used.  This skb was then
passed to ppp_receive_nonmp_frame() without checking if the encapsulated
protocol header could safely be read.
Signed-off-by: NBen McKeegan <ben@netservers.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After commmit 4b77b0a2 EEH breaks
after the second error, since it calls pci_restore_state()
but it returns 0, since pci->state_saved is false.

So, this patch just call pci_save_state() after pci_restore_state().
Signed-off-by: NBreno Leitao <leitao@linux.vnet.ibm.com>
Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

net: Fix the rollback test in dev_change_name()

In dev_change_name() an err variable is used for storing the original
call_netdevice_notifiers() errno (negative) and testing for a rollback
error later, but the test for non-zero is wrong, because the err might
have positive value as well - from dev_alloc_name(). It means the
rollback for a netdevice with a number > 0 will never happen. (The err
test is reordered btw. to make it more readable.)
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Technically there is no need to set the card offline to change
RX checksumming. Get rid of this stupid limitation.
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The maximum TSO size OSA can handle is 15 * PAGE_SIZE. This
patch reduces gso_max_size to this value and adds some sanity
checks and statistics to the TSO implementation.
Since only layer 3 is able to do TSO move all TSO related functions
to the qeth_l3 module.
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Setting a qeth device online requires to call function
ccw_device_set_online() for read-, write-, and data-subchannel.
Failures should be detected immediately without an attempt to
invoke follow-on activity qeth_qdio_clear_card().,

In addition, ccw_device_set_online calls are consolidated in
qeth_core_main.c only.
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

EDDP code has been removed from qeth in 2009. This patch removes two
useless remaining EDDP-references.
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Isolate data connection to a shared OSA card against other data
connections to the same OSA card. Connectivity between isolated
data connections sharing the same OSA card is therefore possible only
through external network gear (e.g. a router).
Signed-off-by: NEinar Lueck <elelueck@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 38783e67.

It causes kernel bugzilla #14594
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function print_mac in net/ethernet/eth.c is marked __deprecated
and not used. Remove it.
Signed-off-by: NMarin Mitov <mitov@issp.bas.bg>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The language of 802.3ad 43.4.9 requires the "recordPDU" function
to, in part, compare the Partner parameter values in a received LACPDU
to the stored Actor values.  If those match, then the Partner's
synchronization state is set to true.

	The current 802.3ad implementation is performing these steps out
of order; first, the synchronization check is done, then the paramters are
checked to see if they match (the synch check being done against a match
check of a prior LACPDU).  This causes delays in establishing aggregators
in some circumstances.

	This patch modifies the 802.3ad code to call __choose_matched,
the function that does the "match" comparisions, as the first step of
__record_pdu, instead of immediately afterwards.  This new behavior is
in compliance with the language of the standard.

	Some additional commentary relating to code vs. standard is also
added.

	Reported by Martin Patterson <martin@gear6.com> who also supplied
the logic of the fix and verified the patch.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 05423b24 (vlan: allow null VLAN ID to be used)
forgot to update __vlan_hwaccel_rx() & vlan_gro_common()

We need to set VLAN_TAG_PRESENT flag in skb->vlan_tci
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the NAPI poll function(emac_poll), check for netif_running()
is unnecassary. In addition to associated runtime overhead, it
also results in a continuous softirq loop when the interface is
brought down under heavy traffic(tested wit Traffic Generator).
Once the interface is disabled, the poll function always returns
zero(with the check for netif_running) and napi_complete() would
never get called resulting in softirq loop.
Signed-off-by: NSriramakrishnan <srk@ti.com>
Acked-by: NChaithrika U S <chaithrika@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the NAPI poll function, check for netif_running() is unnecassary.
In addition to associated runtime overhead, it also results in
continuous softirq loop when the interface is brought down under heavy
traffic(tested with Traffic Generator).Once the interface is disabled,
the poll function always returns zero(with the check for netif_running)
and napi_complete() would never get called resulting in softirq loop.
Signed-off-by: NSriramakrishnan <srk@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates the tg3 version to 3.104.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the 5717 variant device ID enumerations and adds those
DIDs to the PCI ID table.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds code to funnel each MSI-X vector's rx packet buffers
into a single set of producer rings which will then be submitted to the
hardware.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The rx producer mailbox registers are used in several spots in the code.
The addition of TG3_64BIT_REG_LOW makes register references
uncomfortably long.  This patch creates an alias for the standard and
jumbo ring producer index registers to make the code cleaner.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch increases the number of producer rings available and
implements the constructor and destructor code that deals with them.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>