Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 29 11月, 2013 1 次提交
  3. 16 11月, 2013 1 次提交
  5. 08 11月, 2013 1 次提交
  7. 20 10月, 2013 4 次提交
  9. 18 10月, 2013 1 次提交
  11. 04 10月, 2013 1 次提交
    • N
      bonding: modify the old and add new xmit hash policies · 32819dc1
      由 Nikolay Aleksandrov 提交于 
      This patch adds two new hash policy modes which use skb_flow_dissect:
3 - Encapsulated layer 2+3
4 - Encapsulated layer 3+4
There should be a good improvement for tunnel users in those modes.
It also changes the old hash functions to:
hash ^= (__force u32)flow.dst ^ (__force u32)flow.src;
hash ^= (hash >> 16);
hash ^= (hash >> 8);

Where hash will be initialized either to L2 hash, that is
SRCMAC[5] XOR DSTMAC[5], or to flow->ports which should be extracted
from the upper layer. Flow's dst and src are also extracted based on the
xmit policy either directly from the buffer or by using skb_flow_dissect,
but in both cases if the protocol is IPv6 then dst and src are obtained by
ipv6_addr_hash() on the real addresses. In case of a non-dissectable
packet, the algorithms fall back to L2 hashing.
The bond_set_mode_ops() function is now obsolete and thus deleted
because it was used only to set the proper hash policy. Also we trim a
pointer from struct bonding because we no longer need to keep the hash
function, now there's only a single hash function - bond_xmit_hash that
works based on bond->params.xmit_policy.

The hash function and skb_flow_dissect were suggested by Eric Dumazet.
The layer names were suggested by Andy Gospodarek, because I suck at
semantics.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Acked-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      32819dc1
  13. 01 10月, 2013 1 次提交
  15. 29 9月, 2013 1 次提交
  17. 27 9月, 2013 12 次提交
  19. 16 9月, 2013 1 次提交
  21. 12 9月, 2013 1 次提交
  23. 04 9月, 2013 1 次提交
    • V
      bonding: remove bond_vlan_used() · 6f477d42
      由 Veaceslav Falico 提交于 
      We're using it currently to verify if we have vlans before getting the tag
from the skb we're about to send. It's useless because the vlan_get_tag()
verifies if the skb has the tag (and returns an error if not), and we can
receive tagged skbs only if we *already* have vlans.

Plus, the current RCUed implementation is kind of useless anyway - the we
can remove the last vlan in the moment we return from the function.

So remove the only usage of it and the whole function.

CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      6f477d42
  25. 30 8月, 2013 2 次提交
  27. 02 8月, 2013 3 次提交
    • N
      bonding: initial RCU conversion · 278b2083
      由 nikolay@redhat.com 提交于 
      This patch does the initial bonding conversion to RCU. After it the
following modes are protected by RCU alone: roundrobin, active-backup,
broadcast and xor. Modes ALB/TLB and 3ad still acquire bond->lock for
reading, and will be dealt with later. curr_active_slave needs to be
dereferenced via rcu in the converted modes because the only thing
protecting the slave after this patch is rcu_read_lock, so we need the
proper barrier for weakly ordered archs and to make sure we don't have
stale pointer. It's not tagged with __rcu yet because there's still work
to be done to remove the curr_slave_lock, so sparse will complain when
rcu_assign_pointer and rcu_dereference are used, but the alternative to use
rcu_dereference_protected would've created much bigger code churn which is
more difficult to test and review. That will be converted in time.

1. Active-backup mode
 1.1 Perf recording while doing iperf -P 4
  - old bonding: iperf spent 0.55% in bonding, system spent 0.29% CPU
                 in bonding
  - new bonding: iperf spent 0.29% in bonding, system spent 0.15% CPU
                 in bonding
 1.2. Bandwidth measurements
  - old bonding: 16.1 gbps consistently
  - new bonding: 17.5 gbps consistently

2. Round-robin mode
 2.1 Perf recording while doing iperf -P 4
  - old bonding: iperf spent 0.51% in bonding, system spent 0.24% CPU
                 in bonding
  - new bonding: iperf spent 0.16% in bonding, system spent 0.11% CPU
                 in bonding
 2.2 Bandwidth measurements
  - old bonding: 8 gbps (variable due to packet reorderings)
  - new bonding: 10 gbps (variable due to packet reorderings)

Of course the latency has improved in all converted modes, and moreover
while
doing enslave/release (since it doesn't affect tx anymore).

Also I've stress tested all modes doing enslave/release in a loop while
transmitting traffic.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      278b2083
    • N
      bonding: factor out slave id tx code and simplify xmit paths · 15077228
      由 Nikolay Aleksandrov 提交于 
      I factored out the tx xmit code which relies on slave id in
bond_xmit_slave_id. It is global because later it can be used also in
3ad mode xmit. Unnecessary obvious comments are removed. Active-backup
mode is simplified because bond_dev_queue_xmit always consumes the skb.
bond_xmit_xor becomes one line because of bond_xmit_slave_id.
bond_for_each_slave_from is not used in bond_xmit_slave_id because later
when RCU is used we can avoid important race condition by using standard
rculist routines.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      15077228
    • N
      bonding: convert to list API and replace bond's custom list · dec1e90e
      由 nikolay@redhat.com 提交于 
      This patch aims to remove struct bonding's first_slave and struct
slave's next and prev pointers, and replace them with the standard Linux
list API. The old macros are converted to list API as well and some new
primitives are available now. The checks if there're slaves that used
slave_cnt have been replaced by the list_empty macro.
Also a few small style fixes, changing longest -> shortest line in local
variable declarations, leaving an empty line before return and removing
unnecessary brackets.
This is the first step to gradual RCU conversion.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      dec1e90e
  29. 28 6月, 2013 2 次提交
    • N
      bonding: remove unnecessary dev_addr_from_first member · 97a1e639
      由 nikolay@redhat.com 提交于 
      In struct bonding there's a member called dev_addr_from_first which is
used to denote when the bond dev should clone the first slave's MAC
address but since we have netdev's addr_assign_type variable that is not
necessary. We clone the first slave's MAC each time we have a random MAC
set to the bond device. This has the nice side-effect of also fixing an
inconsistency - when the MAC address of the bond dev is set after its
creation, but prior to having slaves, it's not kept and the first slave's
MAC is cloned. The only way to keep the MAC was to create the bond device
with the MAC address set (e.g. through ip link). In all cases if the
bond device is left without any slaves - its MAC gets reset to a random
one as before.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      97a1e639
    • N
      bonding: remove unnecessary setup_by_slave member · 8d2ada77
      由 nikolay@redhat.com 提交于 
      We have a member called setup_by_slave in struct bonding to denote if the
bond dev has different type than ARPHRD_ETHER, but that is already denoted
in bond's netdev type variable if it was setup by the slave, so use that
instead of the member.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      8d2ada77
  31. 26 6月, 2013 2 次提交
    • V
      bonding: add an option to fail when any of arp_ip_target is inaccessible · 8599b52e
      由 Veaceslav Falico 提交于 
      Currently, we fail only when all of the ips in arp_ip_target are gone.
However, in some situations we might need to fail if even one host from
arp_ip_target becomes unavailable.

All situations, obviously, rely on the idea that we need *completely*
functional network, with all interfaces/addresses working correctly.

One real world example might be:
vlans on top on bond (hybrid port). If bond and vlans have ips assigned
and we have their peers monitored via arp_ip_target - in case of switch
misconfiguration (trunk/access port), slave driver malfunction or
tagged/untagged traffic dropped on the way - we will be able to switch
to another slave.

Though any other configuration needs that if we need to have access to all
arp_ip_targets.

This patch adds this possibility by adding a new parameter -
arp_all_targets (both as a module parameter and as a sysfs knob). It can be
set to:

	0 or any (the default) - which works exactly as it's working now -
	the slave is up if any of the arp_ip_targets are up.

	1 or all - the slave is up if all of the arp_ip_targets are up.

This parameter can be changed on the fly (via sysfs), and requires the mode
to be active-backup and arp_validate to be enabled (it obeys the
arp_validate config on which slaves to validate).

Internally it's done through:

1) Add target_last_arp_rx[BOND_MAX_ARP_TARGETS] array to slave struct. It's
   an array of jiffies, meaning that slave->target_last_arp_rx[i] is the
   last time we've received arp from bond->params.arp_targets[i] on this
   slave.

2) If we successfully validate an arp from bond->params.arp_targets[i] in
   bond_validate_arp() - update the slave->target_last_arp_rx[i] with the
   current jiffies value.

3) When getting slave's last_rx via slave_last_rx(), we return the oldest
   time when we've received an arp from any address in
   bond->params.arp_targets[].

If the value of arp_all_targets == 0 - we still work the same way as
before.

Also, update the documentation to reflect the new parameter.

v3->v4:
Kill the forgotten rtnl_unlock(), rephrase the documentation part to be
more clear, don't fail setting arp_all_targets if arp_validate is not set -
it has no effect anyway but can be easier to set up. Also, print a warning
if the last arp_ip_target is removed while the arp_interval is on, but not
the arp_validate.

v2->v3:
Use _bh spinlock, remove useless rtnl_lock() and use jiffies for new
arp_ip_target last arp, instead of slave_last_rx(). On bond_enslave(),
use the same initialization value for target_last_arp_rx[] as is used
for the default last_arp_rx, to avoid useless interface flaps.

Also, instead of failing to remove the last arp_ip_target just print a
warning - otherwise it might break existing scripts.

v1->v2:
Correctly handle adding/removing hosts in arp_ip_target - we need to
shift/initialize all slave's target_last_arp_rx. Also, don't fail module
loading on arp_all_targets misconfiguration, just disable it, and some
minor style fixes.
Signed-off-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      8599b52e
    • V
      bonding: add helper function bond_get_targets_ip(targets, ip) · 87a7b84b
      由 Veaceslav Falico 提交于 
      Add function bond_get_targets_ip(targets, ip) which searches through
targets array of ips (arp_targets) and returns the position of first
match. If ip == 0, returns the first free slot. On failure to find the
ip or free slot, return -1.

Use it to verify if the arp we've received is valid and in sysfs.

v1->v2:
Fix "[2/6] bonding: add helper function bond_get_targets_ip(targets, ip)",
per Nikolay's advice, to verify if source ip != 0.0.0.0, otherwise we might
update 'null' arp_ip_targets' last_rx. Also, address style.
Signed-off-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      87a7b84b
  33. 13 6月, 2013 1 次提交
    • N
      bonding: fix igmp_retrans type and two related races · 4f5474e7
      由 Nikolay Aleksandrov 提交于 
      First the type of igmp_retrans (which is the actual counter of
igmp_resend parameter) is changed to u8 to be able to store values up
to 255 (as per documentation). There are two races that were hidden
there and which are easy to trigger after the previous fix, the first is
between bond_resend_igmp_join_requests and bond_change_active_slave
where igmp_retrans is set and can be altered by the periodic. The second
race condition is between multiple running instances of the periodic
(upon execution it can be scheduled again for immediate execution which
can cause the counter to go < 0 which in the unsigned case leads to
unnecessary igmp retransmissions).
Since in bond_change_active_slave bond->lock is held for reading and
curr_slave_lock for writing, we use curr_slave_lock for mutual
exclusion. We can't drop them as there're cases where RTNL is not held
when bond_change_active_slave is called. RCU is unlocked in
bond_resend_igmp_join_requests before getting curr_slave_lock since we
don't need it there and it's pointless to delay.
The decrement is moved inside the "if" block because if we decrement
unconditionally there's still a possibility for a race condition although
it is much more difficult to hit (many changes have to happen in
a very short period in order to trigger) which in the case of 3 parallel
running instances of this function and igmp_retrans == 1
(with check bond->igmp_retrans-- > 1) is:
f1 passes, doesn't re-schedule, but decrements - igmp_retrans = 0
f2 then passes, doesn't re-schedule, but decrements - igmp_retrans = 255
f3 does the unnecessary retransmissions.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      4f5474e7
  35. 08 6月, 2013 1 次提交
    • J
      bonding: Convert hw addr handling to sync/unsync, support ucast addresses · 303d1cbf
      由 Jay Vosburgh 提交于 
      This patch converts bonding to use the dev_uc/mc_sync and
dev_uc/mc_sync_multiple functions for updating the hardware addresses
of bonding slaves.

	The existing functions to add or remove addresses are removed,
and their functionality is replaced with calls to dev_mc_sync or
dev_mc_sync_multiple, depending upon the bonding mode.

	Calls to dev_uc_sync and dev_uc_sync_multiple are also added,
so that unicast addresses added to a bond will be properly synced with
its slaves.

	Various functions are renamed to better reflect the new
situation, and relevant comments are updated.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Cc: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      303d1cbf
  37. 31 1月, 2013 1 次提交
  39. 05 1月, 2013 1 次提交
  41. 01 12月, 2012 1 次提交
    • Z
      bonding: rlb mode of bond should not alter ARP originating via bridge · 567b871e
      由 zheng.li 提交于 
      Do not modify or load balance ARP packets passing through balance-alb
mode (wherein the ARP did not originate locally, and arrived via a bridge).

Modifying pass-through ARP replies causes an incorrect MAC address
to be placed into the ARP packet, rendering peers unable to communicate
with the actual destination from which the ARP reply originated.

Load balancing pass-through ARP requests causes an entry to be
created for the peer in the rlb table, and bond_alb_monitor will
occasionally issue ARP updates to all peers in the table instrucing them
as to which MAC address they should communicate with; this occurs when
some event sets rx_ntt.  In the bridged case, however, the MAC address
used for the update would be the MAC of the slave, not the actual source
MAC of the originating destination.  This would render peers unable to
communicate with the destinations beyond the bridge.
Signed-off-by: NZheng Li <zheng.x.li@oracle.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      567b871e