Setting Narrow Channel bit in the scan command caused the device
not to send probe request on all the channels
Signed-off-by: NGuy Cohen <guy.cohen@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes callbacks that can be replaced by the generic one.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

this patch removes remaining includes to net/ieee80211.h
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds several parameters to priv.hw_params, for better control
over HW capabilities variants
Signed-off-by: NRon Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch
1. changes the current EEPROM handling through a single HW struct
layout representation, to more general approach, treating the EEPROM
image as a flat bytes array, handling this image through ops functions
and offsets.
2. Eeprom is dynamically allocated accroding HW type
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NRon Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add power level support
Signed-off-by: NMohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes some dead code from the driver.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch distributes the Local Oscillator calibration bursts over time,
so that calibration only happens when it's actually needed.
Currently we periodically perform a recalibration of the whole table.
The table is huge and this takes lots of time. Additionally only small bits
of the table are actually needed at a given time. So instead of maintaining
a huge table with all possible calibration values, we create dynamic calibration
settings that
a) We only calibrate when they are actually needed.
b) Are cached for some time until they expire.
So a recalibration might happen if we need a calibration setting that's not
cached, or if the active calibration setting expires.
Currently the expire timeout is set to 30 seconds. We may raise that in future.

This patch reduces overall memory consumption by nuking the
huge static calibration tables.

This patch has been tested on several 4306, 4311 and 4318 flavours.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The current code checks for the special signature that signifies
a revision 4 SPROM. Now that a rev. 8 SPROM with a 440-byte length
has been found that may not have any special code, this check could
be relaxed. With this patch, if the CRC is incorrect for a 256-byte
SPROM, the code will immediately check for a 440-byte SPROM. If there
is still a CRC error, the size is set to 440 bytes, which allows dumping
of most of any 512-byte SPROM if one is encountered.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This handler is universal for most of the HW
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch defines ANA_PLL values in iwl-csr.h
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch makes some renaming of the ampdu_action functions inside
iwlwifi, and adds checks for correct station id in Rx flows
Signed-off-by: NRon Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes several issues in security:

1) the uCode doesn't know about TKIP-MMIC failure, if uCode set
RX_RES_STATUS_BAD_ICV_MIC, it means ICV failure: drop the packet silently.
2) do not allocate room in the key table of the uCode is the set_key call
is a replacement of an old key
3) check the keyidx of the key in the uCode before removing it upon
disable_key call
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The hw_key_idx inside the ieee80211_key_conf structure does
not provide all the information drivers might need to perform
hardware encryption.

This is in particular true for rt2x00 who needs to know the
key algorithm and whether it is a shared or pairwise key.

By passing the ieee80211_key_conf pointer it assures us that
drivers can make full use of all information that it should know
about a particular key.

Additionally this patch updates all drivers to grab the hw_key_idx from
the ieee80211_key_conf structure.

v2: Removed bogus u16 cast
v3: Add warning about ieee80211_tx_control pointers
v4: Update warning about ieee80211_tx_control pointers
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch cleans up semantic of set_pwr_src
set_pwr_src is now part of apm handlers group
in iwlcore
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch move iwl_find_station into iwl-sta.c file
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch does several things:

1) rename CONFIG_IWL4965_SENSITIVITY to IWL4965_RUN_TIME_CALIB which is
   better semantic
2) move all the run time calibration to a new file: iwl-calib.c
3) simplify the sensitivity calibration flow and make it HW dependent
4) make the chain noise calibration flow HW dependent
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Patch re-ordering could be harmful:

commit 1fd18905
Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Date:   Sat Apr 26 22:25:24 2008 +0200

    ide: add IDE_HFLAG_SERIALIZE_DMA host flag
...

is buggy because ->init_dma method / ide_hwif_setup_dma() is called
before IDE_HFLAG_SERIALIZE_DMA host flag is checked.

Fix it by checking IDE_HFLAG_SERIALIZE[_DMA] after DMA initialization.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new RV2P firmware fixes 2 issues:

1. The jumbo rx buffer page size is now configurable and set to the
   proper PAGE_SIZE.  Before, it was assumed to be always 4K.

2. Driver sometimes would crash when receiving jumbo packets mixed
   with firmware management packets.  This was caused by the old
   firmware DMA'ing to the wrong address.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We should zero out the context memory for 5709 before each reset.  When
we resume after suspend for example, the memory may not be zero and the
chip may not function correctly.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The register BNX2_CTX_STATUS (0x1004) should be skipped on 5709 as it
contains reserved bits.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some remote PHY blade systems, the driver receives no initial link
interrupt.  As a result, the GMII/MII MAC mode does not get setup properly.
To fix this problem, we add an initial poll of the link state after chip
reset.

With this change, the setting of the initial carrier state in the init
code can be eliminated.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnx2_set_remote_link() should be called under bp->phy_lock to protect
against concurrent polling and interrupt calls.  This change is needed
by the next patch which will add one initial poll of the remote PHY
link status.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates the version number to 3.92.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All variants of the 5714, 5715, and 5780 offer a feature called the
"Universal Management Port".  This feature is implemented in firmware
and is largely transparent to the driver, except...

It turns out that the UMP firmware needs to know the current status
of the link.  Because the firmware cannot touch the PHY registers while
the driver is in control of the device, it needs the driver to report
link status changes through an additional handshaking mechanism.
Without this handshake, it has been observed in the field that the UMP
firmware will not operate correctly.

This patch implements the new handshake with the UMP firmware.  Since
the handshake uses the same mechanism ASF heartbeats use, code was
added to detect and wait for completion of a pending previous event.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A CPMU related loopback test bug existed for AX revisions of the 5761.
While that errata has been fixed, the CPMU still slows down the core
clock too far to run the loopback test successfully.  This patch
disables the CPMU LINK_SPEED mode just like we do with the AX
revisions of the 5761 and all revisions of the 5784.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 5761 NVRAM sizes assigned to the nvram_size member are half as big
as they should be.  This patch corrects the NVRAM sizes and replaces
the hardcoded constants with preprocessor constants for readability.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MI clock is not configured correctly on adapters with the CPMU
present.  The tg3 driver has code which statically sets the MI clock to
be a fraction of the speed at which the core clock is running.
However, the CPMU can change the adapter's core clock frequency based
on operating conditions.  Consequently, the MI will run slow when the
core's clock has been slowed down.

There is a new 500KHz constant frequency clock available on adapters
with a CPMU.  This patch removes the static core clock scaling and
configures the MI clock to use this new 500KHz clock instead.

Running the MI clock at slower speeds will not directly result in data
corruption, but it does challenge the PHY read and write routine timeouts.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If someone tries to _urb_unlink while _urb_queue_head is running, he'll see
_urb->queue == NULL and fail to do any locking.  Prevent that from happening
by strategically placed barriers.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By changing drivers/power/pmu_battery.c I now have '_' instead of
' ' (spaces) in /sys:

/sys/devices/platform/pmu-battery.0/power_supply/PMU_battery_0
/sys/class/power_supply/PMU_battery_0

I'm still not sure if some userspace tool out there uses the old paths and
will break now.
Signed-off-by: NChristian Kujau <lists@nerdbynature.de>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

This adds init/exit function callbacks to pda_power, to
provide a place where the platform code can request/free
GPIOs that it wants to use in the is_ac_online, is_usb_online
and set_charge functions.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

Fix following warnings:
WARNING: vmlinux.o(.data+0x17aa88): Section mismatch in reference from the variable asd_pcidev_data to the function .devinit.text:asd_aic9410_setup()
WARNING: vmlinux.o(.data+0x17aa98): Section mismatch in reference from the variable asd_pcidev_data to the function .devinit.text:asd_aic9410_setup()
WARNING: vmlinux.o(.data+0x17aaa8): Section mismatch in reference from the variable asd_pcidev_data to the function .devinit.text:asd_aic9405_setup()

asd_pcidev_data is only used by __devinit asd_pci_probe.  So mark is const and
annotate it __devinitconst to fix the warnings.

[akpm@linux-foundation.org: fix warning]
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Another user of 32bit time
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Create a /sys/class/dpt_i2o directory and populate it with
dptiN directories. Each dptiN directory contains a "dev" file
that makes udev create /dev/dptiN
Signed-off-by: NMiquel van Smoorenburg <miquels@cistron.nl>
Acked-by: NMark Salyzyn <Mark_Salyzyn@adaptec.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This is the code to actually support 64 bit platforms. 64 bit
DMA is enabled on both x86_32 PAE and 64 bit platforms.

This code is based in part on the unofficial adaptec 64-bit
dpt_i2o driver update that I got from Mark Salyzyn at Adaptec.
Signed-off-by: NMiquel van Smoorenburg <miquels@cistron.nl>
Acked-by: NMark Salyzyn <Mark_Salyzyn@adaptec.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Remove virt_to_bus/bus_to_virt code from dpt_i2o, and use
dma_alloc_coherent() / dma_free_coherent().

This is in preparation of 64-bit support, dma_alloc_coherent()
can allocate memory in the lower 32 bits of physical memory
which is needed because the HBA only supports message blocks under 4GB

This code is based in part on the unofficial adaptec 64-bit
dpt_i2o driver update that I got from Mark Salyzyn at Adaptec.
Signed-off-by: NMiquel van Smoorenburg <miquels@cistron.nl>
Acked-by: NMark Salyzyn <Mark_Salyzyn@adaptec.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Update dpt_i2o.c to use the standard __init / __exit
code instead of the legacy '#include "scsi_module.c"' code.

This is needed in preparation of 64-bit support. scsi_module.c
calls scsi_add_host() with the device pointer set to NULL, and that
crashes code like arch/x64/kernel/pci-gart_64.c::need_iommu().

The reboot_notifier code is deleted because it wasn't compiled
in ever anyway, and it would be useless to duplicate it in
the new code.
Signed-off-by: NMiquel van Smoorenburg <miquels@cistron.nl>
Acked-by: NMark Salyzyn <Mark_Salyzyn@adaptec.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

megaraid_sas suspend and resume are inappropriatelly placed in
__devinit section. Remove those placements and make the stuff
dependent on CONFIG_PM.

While at it, mark remove function as __devexit.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Acked-by: N"Yang, Bo" <Bo.Yang@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

For firmware that supports the feature(s), add the ability to start or
stop an array using the associated SCSI commands, to automatically
manage the spin-up of an array on new I/O reporting back the
appropriate check conditions and actions in cooperation with the
normal timeout mechanisms and enable the blackout period management in
the Firmware associated with the background spin-down of the arrays
when the Firmware times out and deems the arrays as idle.
Signed-off-by: NMark Salyzyn <aacraid@adaptec.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>