Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In theory, all the DDI pipe settings should be set here, including
timing and M/N registers. For now, let's just set the DP MSA
attributes.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: fixed up the unused typo in a #define, spotted by Jani
Nikula.]
Reviewed-by: NJani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We're talking about Spread Spectrum Clocks here, thus SSC.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

And also properly wait for its idle bit.

You may notice that DDI_BUF_CTL is enabled in .enable but disabled in
.post_disable instead of .disable. Yes, the mode set sequence is not
exactly symmetrical, but let's assume the spec is correct unless we
can prove it's wrong.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Just set the only bit we need, everything else is either ignored on
HDMI or should be set to zero.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Problems with the previous code:
  - HDMI just uses WRPLL1 for everything, so dual head cases might not
    work sometimes.
  - At encoder->mode_set we just write the PLL register without doing
    any kind of check (e.g., check if the PLL is already being used).
  - There is no way to fail and return error codes at
    encoder->mode_set.
  - We write to PORT_CLK_SEL at mode_set and we never disable it.
  - Machines hang due to wrong clock enable/disable sequence.

So here we rewrite the code, making it a little more like the
pre-Haswell PLL mode set code:
  - Check PLL availability at ironlake_crtc_mode_set.
  - Try to use both WRPLLs.
  - Check if PLLs are used before actually trying to use them, and
    properly fail with error messages.
  - Enable/disable PORT_CLK_SEL at the right place.
  - Add some WARNs to check for bugs.

The next improvement will be to try to reuse PLLs if the timings
match, but this is content for another patch and it's already
documented with a TODO comment.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Previously we were enabling it at mode_set but never disabling. Let's
follow the mode set sequence.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

And the right time is exactly after/before changing PIPE_CONF. See the
documentation about the mode set sequence.

This code is not inside any encoder-specific callback because
DDI_FUNC_CTL is part of the pipe, so it is used by all encoders.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Right now, we're trying to enable LCPLL at every mode set, but we're
never disabling it. Also, we really don't want to be disabling LCPLL
since it requires a very complex disable/enable sequence. This
register should really be set by the BIOS and we shouldn't be touching
it. Still, let's try to check its value and print some errors in case
we find something wrong. We're also adding intel_ddi_get_cdclk_freq
which will be used later in other places.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

I've picked hdmi as the first encoder to convert because it's rather
simple:
- no cloning possible
- no differences between prepare/commit and dpms off/on switching.

A few changes are required to do so:
- Split up the dpms code into an enable/disable function and wire it
  up with the intel encoder.
- Noop out the existing encoder prepare/commit functions used by the
  crtc helper - our crtc enable/disable code now calls back into the
  encoder enable/disable code at the right spot.
- Create new helper functions to handle dpms changes.
- Add intel_encoder->connectors_active to better track dpms state. Atm
  this is unused, but it will be useful to correctly disable the
  entire display pipe for cloned configurations. Also note that for
  now this is only useful in the dpms code - thanks to the crtc
  helper's dpms confusion across a modeset operation we can't (yet)
  rely on this having a sensible value in all circumstances.
- Rip out the encoder helper dpms callback, if this is still getting
  called somewhere we have a bug. The slight issue with that is that
  the crtc helper abuses dpms off to disable unused functions. Hence
  we also need to implement a default encoder disable function to do
  just that with the new encoder->disable callback.
- Note that we drop the cpt modeset verification in the commit
  callback, too. The right place to do this would be in the crtc's
  enable function, _after_ all the encoders are set up. But because
  not all encoders are converted yet, we can't do that. Hence disable
  this check temporarily as a minor concession to bisectability.

v2: Squash the dpms mode to only the supported values -
connector->dpms is for internal tracking only, we can hence avoid
needless state-changes a bit whithout causing harm.

v3: Apply bikeshed to disable|enable_ddi, suggested by Paulo Zanoni.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

HDMI audio related registers will be configured in write_eld callback.
Signed-off-by: NWang Xingchao <xingchao.wang@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If we don't find the exact refresh rate, go with the next one. This
makes some modes work for me. They won't have the best settings, but
will at least have something. Just returning from this function when
we don't find the perfect settings does not help us at all.

Version 2:
  - Remove duplicate lines on the clock table.
  - Add back debug message with refresh, p, n2 and r2.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Don't rely on previous values already set on the register. Everything
we're not explicitly setting should be zero for now.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Correctly erase the values previously set and also check for 6bpc and
10bpc.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

During my tests, everything worked even if the wrong polarity was set.
Still, we should try to set the correct values.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Mask the value before changing it and also select DVI when needed.

DVI was working in cases where the BIOS was setting the correct value
because we were not masking the value before changing it.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Instead of having a giant if cascade to figure this out according to
the passed-in register. We could do quite a bit more cleaning up and
all by using the port at more places, but I think this should be part
of a bigger rework to introduce a struct intel_digital_port which
would keep track of all these things. I guess this will be part of
some haswell-DP-induced refactoring.

For now this rips out the big cascade, which is what annoyed me so
much.

v2: Add port variable name back for the func decl (I've tried to trick
myself below the 80 char limit).
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is required for a stable FDI connection.

v2: fix and simplify the FDI_RX_MISC bits as noticed by Paulo Zanoni.

CC: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need a function that is able to fully 'set' the state of the DIP
registers to a known state.

Currently, we have the write_infoframe function that is called twice:
once for AVI and once for SPD. The problem is that write_infoframe
tries to keep the state of the DIP register as it is, changing only
the minimum necessary bits. The second problem is that
write_infoframe does twice (once for each time it is called) some
work that should be done only once (like waiting for vblank and
setting the port). If we add even more DIPs, it will do even more
repeated work.

This patch only adds the infrastructure keeping the code behavior the
same as before.

v2: add static keywords
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On Haswell, we need to properly train the DDI buffers prior to enabling
HDMI, and enable the required clocks with correct dividers for the desired
frequency.

Also, we cannot simple reuse HDMI routines from previous generations of
GPU, as most of HDMI-specific stuff is being done via the DDI port
programming instead of HDMI-specific registers.

This commit take advantage of the WR PLL clock table which is in a
separate (previous) commit to select the right divisors for each mode.
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This table is used for programming WR PLL clocks, used by HDMI and DVI outputs.
I split it into a separate patch to simplify the HDMI enabling patch which was
getting huge.

Note that this table is a temporary solution for WR PLL programming. It
will be reworked into a more exact algorithm at a later stage. But for
now, it provides the most accurate clock setting solution, so we use it
here.
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Digital port detection on Haswell is indicated by the presence of a bit in
DDI_BUF_CTL for port A, and by a different register for ports B, C and D.
So we check for those bits during the initialization time and let the hdmi
function know about those.

Note that this bit does not indicates whether the output is DP or HDMI.
However, the DDI buffers can be programmed in a way that is shared between
DP/HDMI and FDI/HDMI except for PORT E.

So for now, we detect those digital outputs as being HDMI, but proper DP
support is still pending.

Note that DDI A can only drive eDP, so we do not handle it here for hdmi
initialization.

v2: simplify Haswell handling logic

v3: use generic function for handling digital outputs.
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Starting with Haswell, DDI ports can work in FDI mode to support
connectivity with the outputs located on the PCH.

This commit adds support for such connections in the intel_ddi module, and
provides Haswell-specific functionality to make it work.

v2: simplify the commit as per Daniel Vetter suggestion.
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

DDI is introduced starting with Haswell GPU generation. So to simplify its
management in the future, we also add intel_ddi.c to hold all the
DDI-related items.

Buffer translations for DDI links must be initialized prior to enablement.
For FDI and DP, first 9 pairs of values are used to select the connection
parameters. HDMI uses the last pair of values and ignores the first 9
pairs. So we program HDMI values in both cases, which allows HDMI to work
over both FDI and DP-friendly buffers.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>