Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 12 12月, 2005 5 次提交
  3. 09 12月, 2005 4 次提交
    • D
      [PATCH] powerpc: Fix SLB flushing path in hugepage · 23ed6cb9
      由 David Gibson 提交于 
      On ppc64, when opening a new hugepage region, we need to make sure any
old normal-page SLBs for the area are flushed on all CPUs.  There was
a bug in this logic - after putting the new hugepage area masks into
the thread structure, we copied it into the paca (read by the SLB miss
handler) only on one CPU, not on all.  This could cause incorrect SLB
entries to be loaded when a multithreaded program was running
simultaneously on several CPUs.  This patch corrects the error,
copying the context information into the PACA on all CPUs using the mm
in question before flushing any existing SLB entries.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
      23ed6cb9
    • D
      [PATCH] powerpc: Add missing icache flushes for hugepages · cbf52afd
      由 David Gibson 提交于 
      On most powerpc CPUs, the dcache and icache are not coherent so
between writing and executing a page, the caches must be flushed.
Userspace programs assume pages given to them by the kernel are icache
clean, so we must do this flush between the kernel clearing a page and
it being mapped into userspace for execute.  We were not doing this
for hugepages, this patch corrects the situation.

We use the same lazy mechanism as we use for normal pages, delaying
the flush until userspace actually attempts to execute from the page
in question.

Tested on G5.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
      cbf52afd
    • O
      [PATCH] powerpc: Set cache info defaults · dabcafd3
      由 Olof Johansson 提交于 
      Cache info is setup by walking the device tree in initialize_cache_info().
However, icache_flush_range might be called before that, in
slb_initialize()->patch_slb_encoding, which modifies the load immediate
instructions used with SLB fault code.

Not only that, but depending on memory layout, we might take SLB faults
during unflatten_device_tree. So that fault will load an SLB entry that
might not contain the right LLP flags for the segment.

Either we can walk the flattened device tree to setup cache info, or
we can pick the known defaults that are known to work. Doing it in the
flattened device tree is hairier since we need to know the machine type
to know what property to look for, etc, etc.

For now, it's just easier to go with the defaults. Worst thing that
happens from it is that we might waste a few cycles doing too small
dcbst/icbi increments.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
      dabcafd3
    • M
      [PATCH] Fix windfarm model-id table · 326743ea
      由 Michal Ostrowski 提交于 
      model_id fields of wf_smu_sys_all_params should match the model ID
they are supposed to represent (as commented). Fixes windfarm on some
iMac 8,1 models.

Signed-off-by: Michal Ostrowski <mostrows at watson ibm com>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
      326743ea
  5. 08 12月, 2005 3 次提交
  7. 05 12月, 2005 4 次提交
  9. 04 12月, 2005 11 次提交
  11. 03 12月, 2005 12 次提交
  13. 02 12月, 2005 1 次提交