The random numbers in Bluetooth Low Energy are 64-bit numbers and should
also be little endian since the HCI specification is little endian.

Change the whole Low Energy pairing to use __le64 instead of a byte
array.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

If some of the cleanup commands caused by mgmt_set_powered(off) never
complete we should still force the adapter to be powered down. This is
rather easy to do since hdev->power_off is already a delayed work
struct. This patch schedules this delayed work if at least one HCI
command was sent by the cleanup procedure.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Add the definitions for clearing the LE white list, adding entries to
the LE white list and removing entries from the LE white list.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Some LE controllers don't support scanning and creating a connection
at the same time. So we should always stop scanning in order to
establish the connection.

Since we may prematurely stop the discovery procedure in favor of
the connection establishment, we should also cancel hdev->le_scan_
disable delayed work and set the discovery state to DISCOVERY_STOPPED.

This change does a small improvement since it is not mandatory the
user stops scanning before connecting anymore. Moreover, this change
is required by upcoming LE auto connection mechanism in order to work
properly with controllers that don't support background scanning and
connection establishment at the same time.

In future, we might want to do a small optimization by checking if
controller is able to scan and connect at the same time. For now,
we want the simplest approach so we always stop scanning (even if
the controller is able to carry out both operations).
Signed-off-by: NAndre Guedes <andre.guedes@openbossa.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds a timer for updating the local RPA periodically. The
default timeout is set to 15 minutes.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This code adds a HCI_PRIVACY flag to track whether Privacy support is
enabled (meaning we have a local IRK) and makes sure the IRK is
distributed during SMP key distribution in case this flag is set.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The own_address_type debugfs option does not providing enough
flexibity for interacting with the upcoming LE privacy support.

What really is needed is an option to force using the static address
compared to the public address. The new force_static_address debugfs
option does exactly that. In addition it is also only available when
the controller does actually have a public address. For single mode
LE only controllers this option will not be available.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

This patch implements the Load IRKs command for the management
interface. The command is used to load the kernel with the initial set
of IRKs. It also sets a HCI_RPA_RESOLVING flag to indicate that we can
start requesting devices to distribute their IRK to us.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The LTK key types available right now are unauthenticated and
authenticated ones. Provide two simple constants for it.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

For debugging purposes of Secure Connection Only support a simple
debugfs entry is used to indicate if this mode is active or not.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The security level 4 is a new strong security requirement that is based
around 128-bit equivalent strength for link and encryption keys required
using FIPS approved algorithms. Which means that E0, SAFER+ and P-192
are not allowed. Only connections created with P-256 resulting from
using Secure Connections support are allowed.

This security level needs to be enforced when Secure Connection Only
mode is enabled for a controller or a service requires FIPS compliant
strong security. Currently it is not possible to enable either of
these two cases. This patch just puts in the foundation for being
able to handle security level 4 in the future.

It should be noted that devices or services with security level 4
requirement can only communicate using Bluetooth 4.1 controllers
with support for Secure Connections. There is no backward compatibilty
if used with older hardware.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The Bluetooth 4.1 specification with Secure Connections support has
just been released and controllers with this feature are still in
an early stage.

A handful of controllers have already support for it, but they do
not always identify this feature correctly. This debugfs entry
allows to tell the kernel that the controller can be treated as
it would fully support Secure Connections.

Using debugfs to force Secure Connections support of course does
not make this feature magically appear in all controllers. This
is a debug functionality for early adopters. Once the majority
of controllers matures this quirk will be removed.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The MGMT_SETTING_SECURE_CONN setting is used to track the support and
status for Secure Connections from the management interface. For HCI
based tracking HCI_SC_ENABLED flag is used.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

With the introduction of Secure Connections, the list of link key types
got extended by P-256 versions of authenticated and unauthenticated
link keys.

To avoid any confusion the previous authenticated and unauthenticated
link key types got ammended with a P912 postfix. And the two new keys
have a P256 postfix now. Existing code using the previous definitions
has been adjusted.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The Secure Connections feature introduces the support for P-256 strength
pairings (compared to P-192 with Secure Simple Pairing). This however
means that for out-of-band pairing the hash and randomizer needs to be
differentiated. Two new commands are introduced to handle the possible
combinations of P-192 and P-256. This add the HCI command definition
for both.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The Secure Connections feature is optional and host stacks have to
manually enable it. This add the HCI command definiton for reading
and writing this setting.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The support for Secure Connections introduces two new controller
features and one new host feature.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Some controller pretend they support the Delete Stored Link Key command,
but in reality they really don't support it.

  < HCI Command: Delete Stored Link Key (0x03|0x0012) plen 7
      bdaddr 00:00:00:00:00:00 all 1
  > HCI Event: Command Complete (0x0e) plen 4
      Delete Stored Link Key (0x03|0x0012) ncmd 1
      status 0x11 deleted 0
      Error: Unsupported Feature or Parameter Value

Not correctly supporting this command causes the controller setup to
fail and will make a device not work. However sending the command for
controller that handle stored link keys is important. This quirk
allows a driver to disable the command if it knows that this command
handling is broken.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

This is initial version of
http://tools.ietf.org/html/draft-ietf-6lo-btle-00

By default the 6LoWPAN support is not activated and user
needs to tweak /sys/kernel/debug/bluetooth/hci0/6lowpan
file.

The kernel needs IPv6 support before 6LoWPAN is usable.
Signed-off-by: NJukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Add the LMP feature constants for connectionless slave broadcast
and use them for capability testing.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The Device Under Test (DUT) mode is useful for doing certification
testing and so expose this as debugfs option.

This mode is actually special since you can only enter it. Restoring
normal operation means that a HCI Reset is required. The current mode
value gets tracked as a new device flag and when disabling it, the
correct command to reset the controller is sent.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Enabling and disabling SSP debug mode is useful for development. This
adds a debugfs entry that allows to configure the SSP debug mode.

On purpose this has been implemented as debugfs entry and not a public
API since it is really only useful during testing and development.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

This seems to be a left-over. The module parameter enable_hs has
been removed, but its extern declaration is still present. It is
not needed anymore, so just remove it.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The constants for advertising event types have been defined twice. So
remove one copy of it.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

On controller power on and when enabling LE functionality,
make sure that also the scan response data is correctly set.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

This patch just adds the HCI command structure for configuring the
current IAC LAP setting. The length of the command is variable and
supports more than two IAC. However since there is only general
discoverable and limited discoverable modes, this can be limited
to two possible IACs.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Add a new flag that can be set when in limited discoverable mode. This
flag will cause the limited discoverable bit in the class of device
value to bet set.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Read the current IAC LAP values when initializing the controller. The
values are not used, but it is good to have them in the trace files
for debugging purposes.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

When initializing a controller make sure to read out the number of
supported IAC and store its result. This value is needed to determine
if limited discoverable for BR/EDR can be configured or not.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

When initializing an AMP controller, read its current known location
data so that it can be analyzed later on.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Add constants for ADV_IND, ADV_DIRECT_IND, ADV_SCAN_IND and
ADV_NONCONN_IND advertising types.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Add the basic HCI structure for building the LE advertising parameters
command.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The AMP controller status constants need to be actually used to avoid
crypted hardcoded numbers.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The special AMP controller id 0 is reserved for the BR/EDR controller
that has the main link. It is a fixed value and so use a constant for
this throughout the code to make it more visible when the handling is
for the BR/EDR channel or when it is for the AMP channel.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Add the constants for BR/EDR and 802.11 AMP controller types.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

This flag is used to indicate whether we want to have advertising
enabled or not, so give it a more suitable name.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The Slave Page Response Timeout event indicates to the Host that a
slave page response timeout has occurred in the BR/EDR Controller.

The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.

Bluetooth Core Specification Addendum 4 - Page 110

"7.7.72 Slave Page Response Timeout Event [New Section]
...
Note: this event will be generated if the slave BR/EDR Controller
responds to a page but does not receive the master FHS packet
(see Baseband, Section 8.3.3) within pagerespTO.

Event Parameters: NONE"
Signed-off-by: NDohyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: NC S Bhargava <cs.bhargava@samsung.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The Synchronization Train Complete event indicates that the Start
Synchronization Train command has completed.

The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.

Bluetooth Core Specification Addendum 4 - Page 103

"7.7.67 Synchronization Train Complete Event [New Section]
...

Event Parameters:

Status 0x00       Start Synchronization Train command completed
                  successfully.
       0x01-0xFF  Start Synchronization Train command failed.
                  See Part D, Error Codes, for error codes and
                  descriptions."
Signed-off-by: NDohyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: NC S Bhargava <cs.bhargava@samsung.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The Start_Synchronization_Train command controls the Synchronization
Train functionality in the BR/EDR Controller.

The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.

Bluetooth Core Specification Addendum 4 - Page 86

"7.1.51 Start Synchronization Train Command [New Section]
...
If connectionless slave broadcast mode is not enabled, the Command
Disallowed (0x0C) error code shall be returned. After receiving this
command and returning a Command Status event, the Baseband starts
attempting to send synchronization train packets containing information
related to the enabled Connectionless Slave Broadcast packet timing.

Note: The AFH_Channel_Map used in the synchronization train packets is
configured by the Set_AFH_Channel_Classification command and the local
channel classification in the BR/EDR Controller.

The synchronization train packets will be sent using the parameters
specified by the latest Write_Synchronization_Train_Parameters command.
The Synchronization Train will continue until synchronization_trainTO
slots (as specified in the last Write_Synchronization_Train command)
have passed or until the Host disables the Connectionless Slave Broadcast
logical transport."
Signed-off-by: NDohyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: NC S Bhargava <cs.bhargava@samsung.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

he Set_Connectionless_Slave_Broadcast command controls the
Connectionless Slave Broadcast functionality in the BR/EDR
Controller.

The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.

Bluetooth Core Specification Addendum 4 - Page 78

"7.1.49 Set Connectionless Slave Broadcast Command [New Section]
...
The LT_ADDR indicated in the Set_Connectionless_Slave_Broadcast shall be
pre-allocated using the HCI_Set_Reserved_LT_ADDR command. If the
LT_ADDR has not been reserved, the Unknown Connection Identifier (0x02)
error code shall be returned. If the controller is unable to reserve
sufficient bandwidth for the requested activity, the Connection Rejected
Due to Limited Resources (0x0D) error code shall be returned.

The LPO_Allowed parameter informs the BR/EDR Controller whether it is
allowed to sleep.

The Packet_Type parameter specifies which packet types are allowed. The
Host shall either enable BR packet types only, or shall enable EDR and DM1
packet types only.

The Interval_Min and Interval_Max parameters specify the range from which
the BR/EDR Controller must select the Connectionless Slave Broadcast
Interval. The selected Interval is returned."
Signed-off-by: NDohyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: NC S Bhargava <cs.bhargava@samsung.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>