Some devices (ATI/AMD cards) don't support passing ELD struct to the
hardware but just require filling specific registers and then the
hardware/firmware does the rest. In such cases we need to read the info
from SAD blocks and put them in the correct registers.

agd5f: note that the returned pointer needs to be kfreed as per
Christian's suggestion.

v2: fix warning
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

When KMS has parsed an EDID "detailed timing", it leaves the frame rate
zeroed.  Consecutive (debug-) output of that mode thus yields 0 for
vsync.  This simple fix also speeds up future invocations of
drm_mode_vrefresh().

While it is debatable whether this qualifies as a -stable fix I'd apply
it for consistency's sake; drm_helper_probe_single_connector_modes()
does the same thing already for all probed modes.

Cc: stable@vger.kernel.org
Signed-off-by: NTorsten Duwe <duwe@lst.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

EDID spreads some values across multiple bytes; bit-fiddling is needed
to retrieve these.  The current code to parse "detailed timings" has a
cut&paste error that results in a vsync offset of at most 15 lines
instead of 63.

See

   http://en.wikipedia.org/wiki/EDID

and in the "EDID Detailed Timing Descriptor" see bytes 10+11 show why
that needs to be a left shift.

Cc: stable@vger.kernel.org
Signed-off-by: NTorsten Duwe <duwe@lst.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add a generic helper to fill in an HDMI AVI infoframe with data
extracted from a DRM display mode.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>

The modes are only used from within drm_edid.c so we move them there to
avoid creating duplicates by multiple inclusion of drm_edid_modes.h. As
a side-effect we can also get rid of a few variables that keep track of
the number of entries in the tables and use ARRAY_SIZE() instead.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>

The same function had already been merged with a different name. Remove
the duplicate one but reuse some of its kerneldoc fragments for the
existing implementation.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>

If bit 0 of the features byte (0x18) is set to 0, then, according to
the EDID spec, "the display is non-continuous frequency (multi-mode)
and is only specified to accept the video timing formats that are
listed in Base EDID and certain Extension Blocks".

For more information, please see the EDID spec, check the notes of the
table that explains the "Feature Support" byte (18h) and also the
notes on the tables of the section that explains "Display Range Limits
& Additional Timing Description Definition (tag #FDh)".

Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=45729Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NAdam Jackson <ajax@redhat.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

My cheapo monitor has an invalid block 1, resulting in a lot of dmesg spam every few seconds.

I get it the first time that the entire block is all 0xff..
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: stable@vger.kernel.org [v3.7]
Signed-off-by: NDave Airlie <airlied@redhat.com>

This reverts commit 6f33814b.

The quirk cause a regression, and it looks like the original bug was
simply a lack of FIFO bandwidth on the i915G of the reporter. Which
should eventually be fixed as soon as we get around to implemented
DSPARB FIFO reassignment on gen 3.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=52281
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

drm_rgb_quant_range_selectable() will report whether the monitor
claims to support for RGB quantization range selection.

The information can be found in the CEA Video capability block.

v2: s/quantzation/quantization/ in the comment
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: NDavid Airlie <airlied@linux.ie>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This function returns the VIC of the mode. This value can be used when
creating AVI InfoFrames.

Cc: Thierry Reding <thierry.reding@avionic-design.de>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=50371Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NThierry Reding <thierry.reding@avionic-design.de>
Acked-by: NDave Airlie <airlied@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Those tend to be totally not interesting for end-users, and for
debugging we tend to dump the entire noise anyway by enabling all
debug messages.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=57388Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Use memchr_inv() to check the specified memory region is filled with zero.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

This patch adds support for getting CEA Video ID Code for a given
display mode after matching with edid_cea_modes list. Its index in
the list added with one, gives the desired code.

This exported function will be used by hdmi drivers for composing
AVI info frame data.
Signed-off-by: NStephane Marchesin <marcheu@chromium.org>
Signed-off-by: NRahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Convert #include "..." to #include <path/...> in drivers/gpu/.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Acked-by: NDave Airlie <airlied@redhat.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: NDave Jones <davej@redhat.com>

Tested-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NAdam Jackson <ajax@redhat.com>
Acked-by: NDave Airlie <airlied@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Tested-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NAdam Jackson <ajax@redhat.com>
Acked-by: NDave Airlie <airlied@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Limit printing bad edid information at one time per connector.
Connector that are connected to a bad monitor/kvm will likely
stay connected to the same bad monitor/kvm and it makes no
sense to keep printing the bad edid message.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Reviewed-by: NAdam Jackson <ajax@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The current logic for probing ddc is limited to
2 blocks (256 bytes), this patch adds support
for the 4 block (512) data.

To do this, a single 8-bit segment index is
passed to the display via the I2C address 30h.
Data from the selected segment is then immediately
read via the regular DDC2 address using a repeated
I2C 'START' signal.
Signed-off-by: NShirish S <s.shirish@samsung.com>
Reviewed-by: NJean Delvare <jdelvare@suse.de>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NVille Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

There are two slightly different pieces of code for HDMI VSDB
detection. Unify the code into a single helper function.

Also fix a bug where drm_detect_hdmi_monitor() would stop looking
for the HDMI VSDB after the first vendor specific block is found,
whether or not that block happened to be the HDMI VSDB. The
standard allows for any number of vendor specific blocks to be
present.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NAdam Jackson <ajax@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The length of HDMI VSDB must be at least 5 bytes. Other than the minimum,
nothing else about the length is specified. Check the length before
accessing any additional field beyond the minimum length.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NAdam Jackson <ajax@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Make sure drm_detect_hdmi_monitor() and drm_detect_monitor_audio() don't
access beyond the extension block.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NAdam Jackson <ajax@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Connecting an ASUS VW222S [1] over VGA a garbled screen is shown with
vertical stripes in the top half.

In commit bc42aabc [2]

        commit bc42aabc
        Author: Adam Jackson <ajax@redhat.com>
        Date:   Wed May 23 16:26:54 2012 -0400

            drm/edid/quirks: ViewSonic VA2026w

Adam Jackson added the quirk `EDID_QUIRK_FORCE_REDUCED_BLANKING` which
is also needed for this ASUS monitor.

All log files and output from `xrandr` is included in the referenced
Bugzilla report #17629.

Please note that this monitor only has a VGA (D-Sub) connector [1].

[1] http://www.asus.com/Display/LCD_Monitors/VW222S/
[2] http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commit;h=bc42aabc6a01b92b0f961d65671564e0e1cd7592

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=17629Signed-off-by: NPaul Menzel <paulepanter@users.sourceforge.net>
Cc: <dri-devel@lists.freedesktop.org>
Cc: Adam Jackson <ajax@redhat.com>
Cc: Ian Pilcher <arequipeno@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Neither the drm core nor any of the drivers really need the raw_edid field
of struct drm_display_info for anything. Instead of being useful, it
creates confusion about who is responsible for freeing the memory it points
to and setting the field to NULL afterwards, leading to memory leaks and
dangling pointers.

Remove the raw_edid field, and fix drivers as necessary.
Reported-by: NRussell King <linux@arm.linux.org.uk>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Acked-by: NInki Dae <inki.dae@samsung.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

When a monitor EDID doesn't give the preferred bit, driver assumes
that the mode with the higest resolution and rate is the preferred
mode.  Meanwhile the recent changes for allowing more modes in the
GFT/CVT ranges give actually more modes, and some modes may be over
the native size.  Thus such a mode would be picked up as the preferred
mode although it's no native resolution.

For avoiding such a problem, this patch limits the addition of
inferred modes by checking not to be greater than other modes.
Also, it checks the duplicated mode entry at the same time.
Reviewed-by: NAdam Jackson <ajax@redhat.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NDave Airlie <airlied@redhat.com>

We need to initialize this to false, because the is_rb callback only
ever sets it to true.

Noticed while reading through the code.

Cc: stable@vger.kernel.org
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NAdam Jackson <ajax@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

6 bytes seems to be a reasonable default so far, but for the desperate
it's worth exposing this.

[airlied: change include to module.h for this]

Bugzilla: https://bugzilla.redhat.com/582559Signed-off-by: NAdam Jackson <ajax@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Entirely new class of fail for this one.  The detailed timings are for
normal CVT but the monitor really wanted CVT-R.

Bugzilla: http://bugzilla.redhat/com/516471Signed-off-by: NAdam Jackson <ajax@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

EDID vendor IDs are always 3 characters long (4 with the terminating
0).  It doesn't make any sense to have a (possibly 8-byte) pointer
to the ID string in the quirk structure.
Signed-off-by: NIan Pilcher <arequipeno@gmail.com>
Reviewed-by: NAdam Jackson <ajax@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Requiring the first byte of the EDID base block header to be 0 means we
don't fix up as many transfer errors as we could.  Instead have the
callers specify whether it's meant to be block 0 or not, and
conditionally run header fixup based on that.

Bugzilla: https://bugzilla.redhat.com/812890Signed-off-by: NAdam Jackson <ajax@redhat.com>
Reviewed-by: NAlex Deucher <alexdeucher@gmail.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDave Airlie <airlied@redhat.com>

HD panel (1366x768) found most commonly on laptops can't be represented
exactly in CVT/DMT expression, which leads to 1368x768 instead, because
1366 can't be divided by 8.

Add a hack to convert to 1366x768 manually as an exception.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Acked-by: NAdam Jackson <ajax@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Reviewed-by: NDave Airlie <airlied@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAdam Jackson <ajax@redhat.com>
Tested-by: NTakashi Iwai <tiwai@suse.de>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

EDID 1.4 retcons the meaning of the "GTF feature" bit to mean "is
continuous frequency", and moves the set of supported timing formulas
into the range descriptor itself.  In any event, the range descriptor
can act as a filter on the DMT list without regard to a specific timing
formula.
Signed-off-by: NAdam Jackson <ajax@redhat.com>
Tested-by: NTakashi Iwai <tiwai@suse.de>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Slightly more honest naming.
Signed-off-by: NAdam Jackson <ajax@redhat.com>
Tested-by: NTakashi Iwai <tiwai@suse.de>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

mode_in_range() handles what this was warning about.
Signed-off-by: NAdam Jackson <ajax@redhat.com>
Tested-by: NTakashi Iwai <tiwai@suse.de>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

It won't find any, yet.  Fix up callers to match: standard mode codes
will look prefer r-b modes for a given size if present, EST3 mode codes
will look for exactly the r-b-ness mentioned in the mode code.  This
might mean fewer modes matched for EST3 mode codes between now and when
the DMT mode list regrows the r-b modes, but practically speaking EST3
codes don't exist in the wild.
Signed-off-by: NAdam Jackson <ajax@redhat.com>
Tested-by: NTakashi Iwai <tiwai@suse.de>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

No functional change, but will make an upcoming change clearer.
Signed-off-by: NAdam Jackson <ajax@redhat.com>
Tested-by: NTakashi Iwai <tiwai@suse.de>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAdam Jackson <ajax@redhat.com>
Tested-by: NTakashi Iwai <tiwai@suse.de>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The CEA extension block has a field which describes which YCbCr modes are
supported by the device, use it to fill the drm_display_info color_formats
fields. Also the existence of a CEA extension block is used as indication
that the device supports RGB.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>