Signed-off-by: NAndy Grover <andy.grover@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Backwards compatibility with rds 3.0 causes protocol-
based flow control to be disabled as a side-effect.

I don't want to pull out FC support from the IB transport
but I do want to document and keep the sysctl consistent
if possible.
Signed-off-by: NAndy Grover <andy.grover@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since RDS 3.0 and 3.1 have different packet formats,
we need to wait until after protocol negotiation
is complete to layout the rx buffers.
Signed-off-by: NAndy Grover <andy.grover@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Protocol negotiation is logically a property of the
transports, so rds core need not set it.
Signed-off-by: NAndy Grover <andy.grover@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Of course len is in bytes. Calling it data_len hopefully indicates
a little better what the variable is actually for.
Signed-off-by: NAndy Grover <andy.grover@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAndy Grover <andy.grover@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAndy Grover <andy.grover@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The big differences between RDS 3.0 and 3.1 are protocol-level
flow control, and with 3.1 the header is in front of the data. The header
always ends up in the header buffer, and the data goes in the data page.

In 3.0 our "header" is a trailer, and will end up either in the data
page, the header buffer, or split across the two. Since 3.1 is backwards-
compatible with 3.0, we need to continue to support these cases. This
patch does that -- if using RDS 3.0 wire protocol, it will copy the header
from wherever it ended up into the header buffer.
Signed-off-by: NAndy Grover <andy.grover@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RDS on IB uses privdata to do protocol version negotiation. Apparently
the IB stack will return a larger privdata buffer than the struct we were
expecting. Just to be extra-sure, this patch adds some checks in this area.
Signed-off-by: NAndy Grover <andy.grover@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This will be default cause IB connections to failover faster,
but allow a longer retry count to be used if desired.
Signed-off-by: NAndy Grover <andy.grover@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Eric explained this to me -- and afterwards the comment
made sense, but not before. Add the the critical point
about interfaces having to be gone from the netns before
subsys notifiers are called.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

strlcpy() will always null terminate the string. Also use the
sizeof(version) to strlcopy() the version string.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While looking for other fib_trie problems reported by Pawel Staszewski
I noticed there are a few uses of tnode_get_child() and node_parent()
in lookups instead of their rcu versions.
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During large updates there could be triggered warnings like: "Fix
inflate_threshold_root. Now=25 size=11 bits" if inflate() of the root
node isn't finished in 10 loops. It should be much rarer now, after
changing the threshold from 15 to 25, and a temporary problem, so
this patch tries to handle it automatically using a fix variable to
increase by one inflate threshold for next root resizes (up to the 35
limit, max fix = 10). The fix variable is decreased when root's
inflate() finishes below 7 loops (even if some other, smaller table/
trie is updated -- for simplicity the fix variable is global for now).
Reported-by: NPawel Staszewski <pstaszewski@itcare.pl>
Reported-by: NJorge Boncompte [DTI2] <jorge@dti2.net>
Tested-by: NPawel Staszewski <pstaszewski@itcare.pl>
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Signed-off-by: NRobert Olsson <robert.olsson@its.uu.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During trie_rebalance() we free memory after resizing with call_rcu(),
but large updates, especially with PREEMPT_NONE configs, can cause
memory stresses, so this patch calls synchronize_rcu() in
tnode_free_flush() after each sync_pages to guarantee such freeing
(especially before resizing the root node).

The value of sync_pages = 128 is based on Pawel Staszewski's tests as
the lowest which doesn't hinder updating times. (For testing purposes
there was a sysfs module parameter to change it on demand, but it's
removed until we're sure it could be really useful.)

The patch is based on suggestions by: Paul E. McKenney
<paulmck@linux.vnet.ibm.com>
Reported-by: NPawel Staszewski <pstaszewski@itcare.pl>
Tested-by: NPawel Staszewski <pstaszewski@itcare.pl>
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the physical MTU changes we want to ensure that all existing
VLAN device MTUs do not exceed the new underlying MTU.  This patch
adds that propagation.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The connector test code currently does not work out of the box.  This is
because it uses a connector id that is above the registered limit.  So
rather than force people to stumble through undocumented code wondering
why it isn't working, have the test code use one of the "private" ids by
default.  While I'm in here, clean up the code (kernel and user app) so
that it's a bit more user friendly and verbose in significant things that
it does.  Terse test code wastes people time as they simply enumerate it
with all the same kind of debug messages to get a better feel of what code
is running at any time.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The grammar in most of this file is slightly off, and some sections are
hard to read due to lack of visual clues breaking up related material.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The connector documentation states that the argument to the callback
function is always a pointer to a struct cn_msg, but rather than encode it
in the API itself, it uses a void pointer everywhere.  This doesn't make
much sense to encode the pointer in documentation as it prevents proper C
type checking from occurring and can easily allow people to use the wrong
pointer type.  So convert the argument type to an explicit struct cn_msg
pointer.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Allow setting UFO on tap device and handle UFO packets.
Signed-off-by: NSridhar Samudrala <sri@us.ibm.com>

---------------------------------------------------------
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Allow setting UFO on virtio-net and advertise to host.
Signed-off-by: NSridhar Samudrala <sri@us.ibm.com>
Acked-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Keep the version number marching along as updates come in.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds support for a new copper device for 82598, device id 0x150b.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the link comes up, the driver detects which flow control settings are
active.  This is done using bitwise operations directly from the hardware
registers, and assumes the proper boolean assignment.  Make this an
explicit boolean value before assignment to the bool.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ethtool offline test is the only consumer of the legacy descriptors.
Update that path to only use advanced descriptors, and remove all support
for legacy descriptors.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pure style cleanups.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MII speed calculation was based on the CPU clock (ppc_proc_freq),
but for MPC512x we must use the bus clock instead.

This patch makes it use the correct clock and makes sure we don't
clobber reserved bits in the MII_SPEED register.
Signed-off-by: NWolfgang Denk <wd@denx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: <netdev@vger.kernel.org>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/wireless/orinoco/main.c

When the driver received an EEM packet with CRC option enabled, driver must
compute and check the CRC of the Ethernet data. Previous version computes CRC
on Ethernet data plus the original CRC value. Skbuff is correctly trimed but
the old length is used when CRC is computed.
Signed-off-by: NVincent CUISSARD <vincent.cuissard@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove debug DPRINTK in DCB mode netlink interface.
Signed-off-by: NLucy Liu <lucy.liu@intel.com>
Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change clears the address data block memory space, which is needed for
the 82598 which does not have a SAN MAC.
Signed-off-by: NLucy Liu <lucy.liu@intel.com>
Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit changes to shutdown path broke startup on some systems.

revert commit c0bad0f2Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit e912b114
(net: sk_prot_alloc() should not blindly overwrite memory)
took care of not zeroing whole new socket at allocation time.

sock_copy() is another spot where we should be very careful.
We should not set refcnt to a non null value, until
we are sure other fields are correctly setup, or
a lockless reader could catch this socket by mistake,
while not fully (re)initialized.

This patch puts sk_node & sk_refcnt to the very beginning
of struct sock to ease sock_copy() & sk_prot_alloc() job.

We add appropriate smp_wmb() before sk_refcnt initializations
to match our RCU requirements (changes to sock keys should
be committed to memory before sk_refcnt setting)
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

E100 places it's RX packet descriptors inside skb->data and uses them
with bidirectional streaming DMA mapping. Unfortunately it fails to
transfer skb->data ownership to the device after it reads the
descriptor's status, breaking on non-coherent (e.g., ARM) platforms.

This have to be converted to use coherent memory for the descriptors.
Signed-off-by: NKrzysztof Halasa <khc@pm.waw.pl>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bonding device forbids slave device of different types under the same
master.

However, it is possible for a bonding master to change type during its
lifetime.  This can be either from ARPHRD_ETHER to ARPHRD_INFINIBAND
or the other way arround.  The change of type requires device level
multicast address cleanup because device level multicast addresses
depend on the device type.

The patch adds a call to dev_close() before the bonding master changes
type and dev_open() just after that.

In the example below I enslaved an IPoIB device (ib0) under
bond0. Since each bonding master starts as device of type ARPHRD_ETHER
by default, a change of type occurs when ib0 is enslaved.

This is how /proc/net/dev_mcast looks like without the patch

5    bond0           1     0     00ffffffff12601bffff000000000001ff96ca05
5    bond0           1     0     01005e000116
5    bond0           1     0     01005e7ffffd
5    bond0           1     0     01005e000001
5    bond0           1     0     333300000001
6    ib0             1     0     00ffffffff12601bffff000000000001ff96ca05
6    ib0             1     0     333300000001
6    ib0             1     0     01005e000001
6    ib0             1     0     01005e7ffffd
6    ib0             1     0     01005e000116
6    ib0             1     0     00ffffffff12401bffff00000000000000000001
6    ib0             1     0     00ffffffff12601bffff00000000000000000001

and this is how it looks like after the patch.

5    bond0           1     0     00ffffffff12601bffff000000000001ff96ca05
5    bond0           1     0     00ffffffff12601bffff00000000000000000001
5    bond0           1     0     00ffffffff12401bffff0000000000000ffffffd
5    bond0           1     0     00ffffffff12401bffff00000000000000000116
5    bond0           1     0     00ffffffff12401bffff00000000000000000001
6    ib0             1     0     00ffffffff12601bffff000000000001ff96ca05
6    ib0             1     0     00ffffffff12401bffff00000000000000000116
6    ib0             1     0     00ffffffff12401bffff0000000000000ffffffd
6    ib0             2     0     00ffffffff12401bffff00000000000000000001
6    ib0             2     0     00ffffffff12601bffff00000000000000000001
Signed-off-by: NMoni Shoua <monis@voltaire.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix misplaced parenthesis
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Parentheses are required or the comparison occurs before the bitand.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a slab cache uses SLAB_DESTROY_BY_RCU, we must be careful when allocating
objects, since slab allocator could give a freed object still used by lockless
readers.

In particular, nf_conntrack RCU lookups rely on ct->tuplehash[xxx].hnnode.next
being always valid (ie containing a valid 'nulls' value, or a valid pointer to next
object in hash chain.)

kmem_cache_zalloc() setups object with NULL values, but a NULL value is not valid
for ct->tuplehash[xxx].hnnode.next.

Fix is to call kmem_cache_alloc() and do the zeroing ourself.

As spotted by Patrick, we also need to make sure lookup keys are committed to
memory before setting refcount to 1, or a lockless reader could get a reference
on the old version of the object. Its key re-check could then pass the barrier.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NPatrick McHardy <kaber@trash.net>

The first argument is the address family, the second one the hook
number.
Signed-off-by: NPatrick McHardy <kaber@trash.net>