As per hardware recommendation, for every capture stream completion
following operations need to be done in order to reflect the actual
data that is received in position buffer.

1. Wait for 20us before reading the DMA position in buffer once the
interrupt is generated for stream completion.
2. Read any of the register to flush the DMA position value. This is
dummy read operation.
Signed-off-by: NDharageswari R <dharageswari.r@intel.com>
Signed-off-by: NHardik T Shah <hardik.t.shah@intel.com>
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Skylake driver topology header/driver structure is referenced and used
in SST library which creates circular dependency. Hence the
rearrangement.
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

We should not hard code the ACPI path to get acpi_handle. Instead use
ACPI_HANDLE macro to do the job.
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Initially vmixer and mixer widget handlers were bit different, but over
time they became same so remove the duplicate code.
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

A module may have multiple instances in DSP, so unload only when usage
count is zero.
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Add constraint to FE to restrict sample format to 16-bit for bxt_rt298
machine
Signed-off-by: NG Kranthi <gudishax.kranthikumar@intel.com>
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

When creating the codec dai, use sig_bits to update the max bps based
on the codec capability. So both the link DMA and codec format will be
calculated based on DAI sig_bits.

So update the sig_bits with converter capability and use the sig_bits
for HDA format calculation.
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

For calculating the HDA DMA format, use the max_bps supported by the
DAI caps instead of fixing it to 32/24. For host DMA the Max bps support
is 32, but in case of link DMA, this depends on the codec capability.
So use the sig_bits to define the bps supported by dai.
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

LLCH is a 16 bit register. Use readw instead of readl API.
Signed-off-by: NB, Jayachandran <jayachandran.b@intel.com>
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Acked-by: NTakashi Iwai <tiwai@suse.de>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The variable 'data' is assigned null and never re-assigned. There
is also a redundant check for data being non-null which is always
false, so remove this and the variable data and dma_addr as they
are not used once the dead code has been removed.

Detected with CoverityScan, CID#1324015 ("'Constant' variable gaurds
dead code")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Acked-by: NJie Yang <yang.jie@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Intel SST driver spews an info message "FW Versoin xxxx" at each time
the device gets initialized.  Since it's triggered at each PM (or even
runtime PM), it appears so ofetn, and rather becomes annoying than
useful.

This patch suppresses the superfluous messages by checking the
currently loaded FW version with the previously loaded one.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

This patch adds a platform clock widget to turn off the clock only when
both headset capture and headset playback are not in use. This removes
turning off the clock in hw_free so that the clock is on when
either capture or playback of headset is in progress.
Signed-off-by: NHarsha Priya <harshapriya.n@intel.com>
Signed-off-by: NSathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

KPB module default parameter were overwritten by the dynamic instance
id once use case is executed. This will cause module crash from
subsequent execution of use case as the updated parameters are used.

So instead of over writing the default parameter, make a copy and
update the module parameter and use this in IPC message.
Signed-off-by: NDharageswari R <dharageswari.r@intel.com>
Signed-off-by: NKranthikumar, GudishaX <gudishax.kranthikumar@intel.com>
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

When module size > DMA buffer size, driver copies first chunk and waits
for the BDL complete interrupt. BDL complete interrupt never occurs and
wait time expires as module load IPC is not send to start the DMA from
DSP.

To fix the above issue need to follow the below steps:
1. After copying the first chunk, send the module load IPC to start the
DMA.
2. Wait for the BDL interrupt. Once interrupt is received, copy the
next chunk.
3. Continue step 2 till all bytes are copied.
4. When all the bytes are copied (bytes_left = 0), wait for module load
IPC response
5. Handled module load IPC response messages, check the load module IPC
response and wake up the thread to complete module load.
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

dsp ops is already set in init, so use this in cleanup routine
instead of again retrieving it. Also constify struct skl_dsp_ops.
Signed-off-by: NG Kranthi <gudishax.kranthikumar@intel.com>
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

DSP firmware sends notification every 1ms, which is disabled in runtime
suspend. But if a system has no runtime pm, we keep getting
notification, so disable after FW init as well.
Signed-off-by: NG Kranthi <gudishax.kranthikumar@intel.com>
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Remove BE prepare ops which enables MCLK by default. If MCLK is required
to be enabled for any specific platform, it needs to be enabled in the
corresponding machine driver.
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

If D3 IPC fails or times out, firmware needs to be reloaded as driver
continues the reset.
So set the fw_load flag to false to reload the firmware in D0.
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

In system suspend, firmware needs to be re-downloaded as IMR is cleared.
When firmware is downloaded in D0, core state is not set to running
state causing instability with subsequent D0-D3 cycles.

So set the core state correctly during D0 and check the DSP core state
if not in reset to set the DSP to D3.
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

When DSP is in D3, no interrupts are expected, so disable
interrupt while entering D3.
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

If the widget is a mixin module, just unbind between source and sink
and don't stop the source pipe as there can be multiple sinks
connected.
Signed-off-by: NGuneshwor Singh <guneshwor.o.singh@intel.com>
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

DSP pipe needs to stopped before deleting the pipe. Currently check is
for pipe state > STARTED, which is incorrect. So changed to include
pipe state STARTED to stop the pipe if it started.
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Make sure this machine driver is only used if enabled explicitly
and if there is no information found in the SSDT.
Signed-off-by: NPierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Add card with dummy codec and DAI to make I2S signals observable.
Uses Mic and Speaker pins/widgets to control DAPM
Signed-off-by: NPierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Add entries in HID table and reference to bytcht_da7213 driver
Signed-off-by: NPierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Add new machine driver, tested with Ard-Audio-DA7212 [1]
connected to MinnowBoardMAX Turbot.

The MCLK is managed by the codec driver using the "mclk" handle
to reuse existing code, but it could just as well be handled
by this machine driver.

[1] http://www.dialog-semiconductor.com/content/ard-audio-da7212Signed-off-by: NPierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

As a commit 4cd9899f ("ASoC: Intel: Skylake: Add multiple pin
formats") describes, 'fixups is applied to pin 0 only'. On the other
hand, the commit left some codes as what they were. This might
confuses readers.

This commit fixes the issue. This doesn't change driver behaviour at all.

Fixes: 4cd9899f ("ASoC: Intel: Skylake: Add multiple pin formats")
Signed-off-by: NTakashi Sakamoto <takashi.sakamoto@miraclelinux.com>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Tested-by: NSubhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

In 'include/linux/kernel.h', there's a helper macro to round numerical
value. Let's use it.
Signed-off-by: NTakashi Sakamoto <takashi.sakamoto@miraclelinux.com>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Tested-by: NSubhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

During S3->S0 transition, sometime ROM init fails because of
authentication engine loads later than the OS. In this case driver
waits for a longer period and then retries the FW download causing
huge delay in resume time of audio device.

To avoid this, ROM INIT wait time is set to a optimal value and
increased the retries for firmware download.
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Store the DSP firmware/library at boot, so that for S3 to S0 transition
use the stored ctx for downloading the firmware to DSP memory.
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Since index is always 0 replace devm_gpiod_get_index() by devm_gpiod_get()
and apply proper flags.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NLiam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Trivial fix to spelling mistake in dev_err message.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

sched/headers: Prepare to move signal wakeup & sigpending methods from <linux/sched.h> into <linux/sched/signal.h>

Fix up affected files that include this signal functionality via sched.h.
Acked-by: NLinus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NIngo Molnar <mingo@kernel.org>

The sequencer FIFO management has a bug that may lead to a corruption
(shortage) of the cell linked list.  When a sequencer client faces an
error at the event delivery, it tries to put back the dequeued cell.
When the first queue was put back, this forgot the tail pointer
tracking, and the link will be screwed up.

Although there is no memory corruption, the sequencer client may stall
forever at exit while flushing the pending FIFO cells in
snd_seq_pool_done(), as spotted by syzkaller.

This patch addresses the missing tail pointer tracking at
snd_seq_fifo_cell_putback().  Also the patch makes sure to clear the
cell->enxt pointer at snd_seq_fifo_event_in() for avoiding a similar
mess-up of the FIFO linked list.
Reported-by: NDmitry Vyukov <dvyukov@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Dell Inspiron 17 7000 Gaming laptop needs a similar quirk like
Inspiron 7599 to support its subwoofer speaker.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=194191
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Currently ctxfi driver tries to set only the 64bit DMA mask on 64bit
architectures, and bails out if it fails.  This causes a problem on
some platforms since the 64bit DMA isn't always guaranteed.  We should
fall back to the default 32bit DMA when 64bit DMA fails.

Fixes: 6d74b86d ("ALSA: ctxfi - Allow 64bit DMA")
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When a user sets a too small ticks with a fine-grained timer like
hrtimer, the kernel tries to fire up the timer irq too frequently.
This may lead to the condensed locks, eventually the kernel spinlock
lockup with warnings.

For avoiding such a situation, we define a lower limit of the
resolution, namely 1ms.  When the user passes a too small tick value
that results in less than that, the kernel returns -EINVAL now.
Reported-by: NDmitry Vyukov <dvyukov@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Now that %z is standartised in C99 there is no reason to support %Z.
Unlike %L it doesn't even make format strings smaller.

Use BUILD_BUG_ON in a couple ATM drivers.

In case anyone didn't notice lib/vsprintf.o is about half of SLUB which
is in my opinion is quite an achievement.  Hopefully this patch inspires
someone else to trim vsprintf.c more.

Link: http://lkml.kernel.org/r/20170103230126.GA30170@avx2Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix typos and add the following to the scripts/spelling.txt:

  followings||following

While we are here, add a missing colon in the boilerplate in DT binding
documents.  The "you SoC" in allwinner,sunxi-pinctrl.txt was fixed as
well.

I reworded "as the followings:" to "as follows:" for
drivers/usb/gadget/udc/renesas_usb3.c.

Link: http://lkml.kernel.org/r/1481573103-11329-32-git-send-email-yamada.masahiro@socionext.comSigned-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix typos and add the following to the scripts/spelling.txt:

  overwrien||overwritten

Link: http://lkml.kernel.org/r/1481573103-11329-30-git-send-email-yamada.masahiro@socionext.comSigned-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>