When receiving L2CAP Create Channel Request set the channel as
L2CAP_FCS_NONE. Then in "L2CAP Config req" following field will
be set: "FCS Option 0x00 (No FCS)". So by default High Speed
channels have no FCS.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Instead of printing:
"[ 7763.082007] Bluetooth: 2"
print something like:
"[ 7763.082007] Bluetooth: Trailing bytes: 2 in sframe"
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

local_amp_id is used in l2cap_physical_cfm and shall be set up
before calling it.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

When receiving Physical Link Completed event we need to create L2CAP
channel with L2CAP Create Chan Request. Current code was sending
this command only if connection was pending (which is probably
needed in channel move case). If channel is not moved but created
Create Chan should be sent for outgoing channel which is checked
with BT_CONNECT flag.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Read Local OOB Data command can take more than 1 second on some chips.
e.g. on CSR 0a12:0001 first call to Read Local OOB Data after reset
takes about 1300ms resulting in tx timeout error.

[27698.368655] Bluetooth: hci0 command 0x0c57 tx timeout

2012-10-31 15:53:36.178585 < HCI Command: Read Local OOB Data (0x03|0x0057) plen 0
2012-10-31 15:53:37.496996 > HCI Event: Command Complete (0x0e) plen 36
    Read Local OOB Data (0x03|0x0057) ncmd 1
    status 0x00
    hash 0x92219d9b447f2aa9dc12dda2ae7bae6a
    randomizer 0xb1948d0febe4ea38ce85c4e66313beba
Signed-off-by: NSzymon Janc <szymon.janc@tieto.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Vendor-specific ID for BCM20702A0.
Support for bluetooth over Asus Wi-Fi GO!, included with Asus P8Z77-V
Deluxe.

T:  Bus=07 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0b05 ProdID=17b5 Rev=01.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM20702A0
S:  SerialNumber=94DBC98AC113
C:  #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I:  If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

Cc: stable@vger.kernel.org
Signed-off-by: NJeff Cook <jeff@deserettechnology.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Set chan->fcs to L2CAP_FCS_NONE only for new L2CAP channels
(not moved). Other side can still request to use FCS.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Remove locking from l2cap_physical_cfm and lock chan inside
amp_physical_cfm.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

local_amp_id is already set in l2cap_connect() which is called several
lines above.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Use helper instead of test_bit. This is the only place left using
test CONF_CONNECT_PEND flag.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

This patch adds a callback for the HCI_LE_Set_Advertise_Enable command.
The callback is responsible for updating the HCI_LE_PERIPHERAL flag
updating as well as updating the advertising data flags field to
indicate undirected connectable advertising.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

This patch adds support for setting basing LE advertising data. The
three elements supported for now are the advertising flags, the TX power
and the friendly name.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

The core specification defines 127 as the "not available" value (well,
"reserved" for BR/EDR and "not available" for LE - but essentially the
same). Therefore, instead of testing for 0 (which is in fact a valid
value) we should be using this invalid value to test if the tx_power is
available.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

2484 Mhz (Japan) usage requires filter coefficients to
be programmed in the CCK TX FIR registers. This is required
for AR9331, AR9485 and AR9462. Fix this and also remove
a few useless macros and a duplicate variable.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's no need to ask the user about lib80211
since it will be selected by drivers requiring
it, hide it from Kconfig.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver doesn't use any lib80211 symbols
so it shouldn't select it in Kconfig.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Acked-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Using eth_zero_addr() to assign zero address insetad of
memset() or an inefficient copy from a static array.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove unnecessary if statements because libipw_set_geo always
returns success.  Also change function's return value from int
to void.
Signed-off-by: NStanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Removing obsolete functions and prototypes. Moving (and renaming)
defines to place with similar definitions. Removing unnecessary
includes.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When debug is turned on for fwil then the whole data buffer is
dumped. In some cases this gives excessive amount of debug. With
this patch the dumps are limited to 64 bytes.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On sdio module unload followed by load (without removing the
device) the access window should be moved back to enumeration
space. Force this by removing initialisation of sbwad during
probe.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

brcmf_ops_sdio_probe used the private_date func->card->dev to
store device data of brcmfmac sdio. This is not a good place to
store the data. Use dev of func and use func->card->sdio_func
to group the functions the driver is using.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

on sdio remove the bus_if should be configured for close, so
new data from higher layers will be blocked. Also the access
to bus_if in the watchdog should be checked for null pointer
access on sdio remove.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

when brcmf_sdbrcm_probe_attach results in error then cleanup
will result in null pointer access. In brcmf_sdbrcm_release and
in brcmf_ops_sdio_remove. This patch fixes order of init and
de-init.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In brcmf_sdbrcm_probe only error ELINK is seen as error. However
brcmf_bus_start can return many more error codes and all should
result in failed init of driver.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The IF event need special care. It can be either an ADD, DEL, or
CHANGE. For an ADD we need to call brcmf_add_if() before the
event handler call. Upon a DEL we need to call brcmf_del_if()
after the event handler call. CHANGE does not require special
attention.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Firmware fires IF event to add the primary interface but that
is already created in the driver.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Replaced <linux/unaligned/access_ok.h> by <asm/unaligned.h>
to make it work on ARM and other architectures.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

brcmf_fweh_detach can be called while ifp is already NULL, due to
init error. Fix NULL pointer access by checking ifp.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The mac_addr field in ifp object is always valid so no need to
validate.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The function brcmf_add_if() is called with mac address set to NULL
for the primary interface. When handling IF ADD events the firmware
provides a address mask in the event to derive its mac address from
the primary mac address. Rename the parameter and use it as a mask.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Testing revealed the IF ADD event contains the interface
index of the new interface. This would result in a NULL
pointer access when handling the event.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

virtual netdevice interface like P2P client and GO need
different callbacks for .open and .down. This patch adds
those.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The brcmf_add_if() function had a struct device as parameter
to accomodate the bus specific code to use this function. The
driver has been reworked so the bus specific code does not need
this function. Better replace the parameter with a more specific
driver object, ie. struct brcmf_pub.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add support for usb suspend/resume.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Clean code related to firmware download routines. Remove obsolete
delay and increase delay after reset command.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Handling of firmware event has been reworked into a seperate
code file. The change is needed as firmware event can be received
in interrupt context. Decoupling of the event handling has been
lowered to allow event processing to sleep.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

'|' has higher precedence than ?:.  Since AR5K_PHY_TURBO_MODE is 0x1 and
"AR5K_PHY_TURBO_MODE | (ah->ah_radio == AR5K_RF2425)" is true then we
always set turbo to zero.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Simplify the code by make use of module_platform_driver macro.
Signed-off-by: NSyam Sidhardhan <s.syam@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>