There are several occasions where a scan of the same type is requested
concurrently, so logging every time this happens is just noisy and
unnecessary.  Remove the logging for these cases.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This is just a copy-paste in order to make changes tracking
easier.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

For a000 FW moved to 15 as management TID.
The change for us is fairly local - translate old TID to 15
when enabling and disabling a queue, and make sure to cover
it also on TX responses.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

a000 devices queue management is going to change significantly.
We will have 512 queues. Those queues will be assigned number
by the firmware and not by the driver.

In addition, due to SN offload having TX queue shared between TIDs
is impossible

Also, the ADD_STA command no longer updates queues status.
The only point of changing queue in the SCD queue config API.

From driver perspective we have here a new design:

Queue sharing and inactivity checks are disabled.

Once this is done, the only paths that call scd_queue_cfg command
are paths that alloc and release TX queues - which will make future
accommodation to queue number assignment by FW easier.
Since allocating 512 queues statically is not advisable, transport
will allocate the queue on demand, fill the command with DRAM data
and send it. This is reflected in the new transport API.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In a000 devices the TX handling is different in a few ways:
* Queues are allocated dynamically
* DQA is enabled by default
* Driver shouldn't access TFH registers - ucode configures it
  all in SCD_QUEUE_CFG command

Support all this in a new API with op mode, where op mode sends
the command, transport will allocate the queue dynamically, fill
in DMA properties, send the command to FW and get the ID back.
Current implementation only sets the new transport API and fills
the DMA properties.
Future patches will complete the other parts.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Support the new TX command API for a000 devices.
Command is a very slim version of current TX command.
Generalize iwl_mvm_tx_mpdu to get rid of TX command dependencies.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Dynamic SAR allows changing TX power limits at runtime to comply with
SAR regulations on multiple form factors (e.g. tablet vs. clamshell
mode).  To support this, a new table was added to ACPI, which is
called Extended Wireless Regulatory Descriptor (EWRD).  This table
allows OEMs to define different TX power profiles for each form-factor
or usage mode.

Read this new table and store it in our SAR profiles table, in
preparation for Dynamic SAR support.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

For dynamic SAR, we will need to select the current profile from
different places.  In preparation for that, spin the profile selection
code out of iwl_mvm_sar_init().
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We are adding support for dynamic TX power tables for SAR (specific
absorption rate) compliance.  Currently, we only support a single
(static) TX power table, which is read from ACPI, and use it
statically.

To prepare for more tables that can be switched dynamically, refactor
the SAR init flow to allow reusage and add the current static table as
a single entry in an array of tables.
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Firmware isn't configuring multi RX queue hardware yet in
the self init mode.
Disable it for now until we have an API that enables it.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

API will be the same regardless of FW compilation.
CDB related values will be filled in only for CDB.
Cahneg code and names accordingly.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In a000 devices we will support up to 32 stations.
The max station define is used also for invalid station marking
which makes finding usages of actual maximum station pretty hard
to sort through - change it to be a different define in order
to make future changes easier.
Use also ARRAY_SIZE intead of define when possible.
Do not move yet to 32 stations until firmware do it though.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

iwl_has_secure_boot() isn't getting called anywhere. Clean it up.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Currently aux & broadcast queues are added before calling add
station, which results with a SCD_QUEUE_CFG command sent with
a station id unknown yet to fw.
While this works for pre-a000 firmware, the a000 fw requires
the order to be reversed.
The reason the change is only for a000 devices and not for
previous devices is that we cannot reverse the order since
the tfd_queue_mask containing the aux queue will cause FW to
assert on adding a queue mask with a queue that is not enabled.
This is not a problem in a000 fw since the tfd_queue_mask was
removed from the add sta API.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Addresses were changed for a000 devices.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The fwsignal module is only referenced by the bcdc module and part of the
bcdc protocol. So only build it when CONFIG_BRCMFMAC_PROTO_BCDC is selected.

Fixes: acf8ac41 ("brcmfmac: remove reference to fwsignal data from struct brcmf_pub")
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Consequently refer to external PA instead of inverting the logic and
use an internal PA capability flag which is a bit confusing.
Currently this is used for Rt3352 only, but MT7620A also allows for an
external PA which will be supported by a follow up patch.
Signed-off-by: NDaniel Golle <daniel@makrotopia.org>
Acked-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When driver is going to sleep, it does not leave LPS/IPS, thus the
BTCoex may have mismatch when driver wakes up. To avoid that, BTCoex
needs to clear the IPS/LPS state when it receives a pnp notify, then
it can properly set up the hw when driver wakes up.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When wifi is on a 5G channel, the 5G signal will not interfere bt 2.4G
signal, and they can transmit simultaneously, hence there is no need to
switch antenna between wifi and bt.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When wifi is scanning and not connected, set the tdma and coex table
properly to control the priority of the packets to make the wifi bt
coexistence operate smoothly
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

With bt inquiry, the wifi may start as a softap or the wifi and bt are
busy, we take these scenarios into consider to avoid bt inquiry to
degrade the performance of the network
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Move the bt disable flag to a global structure to indicate that bt is
turned off.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

If the device has wifi mode only, there is no need to initiate the
hardware for wifi and bt coexistence, so just return to avoid it.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When wifi is associating or authenticating, set the coex table for wifi
to establish link. These packets should have higher priority.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

To support miracast and P2P, the chip may operate under concurrent mode,
In this situation, do not aggregate tx packet and properly set the rx
aggregation size.

We detect it by monitoring the number of link established.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Set antenna control path if PTA is in control of the packet path of wifi
and bt. If wifi is turned off, tell the PTA about it.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The antenna position setting is useless for 1 antenna chip.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Mask out the connect-idle bit.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

For newer fw, the coex table setting needs to be modified to operate
correctly.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This function checks if wifi has changed its statusi. It will be needed
in the future.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

For ap mode, adjust fw settings to operate properly.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Clear the hid_exist flag by monitoring the packet counter.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

These bt information are displayed in display coex
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Let bt control the aggregation size to improve stability.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

If we don't limit the rx aggregation size, and set tdma instead, the bt profile can
get more stable.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Before firmware is ready, set GNT_BT to high to let bt transmit
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When power on, the wifi could be initiating, force the antenna to
transmit bt packets to avoid bt unstable problems
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

In mp mode, the wifi will not turn off and still has control of the PTA,
so the driver needs to distinguish whether it is mp mode or not
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

For scan notify, we need to supervise some registers to make sure that
coexistence is operating as we expected.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>