Current initialization sequence is lacking, causing some configurations
to fail.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The phy's firmware version isn't being parsed properly as it's
currently parsed like the rest of the 848xx phys.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There's a problem in current 84833 phy configuration -
in case 1Gb link is configured and jumbo-sized packets are being
used, device will experience RX crc errors.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, when link is using KR2 it cannot be forced to any speed other
than 20g.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.om>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dm9000 driver doesn't work in at least one device-tree
configuration, spitting an error message on irq resource :
[    1.062495] dm9000 8000000.ethernet: insufficient resources
[    1.068439] dm9000 8000000.ethernet: not found (-2).
[    1.073451] dm9000: probe of 8000000.ethernet failed with error -2

The reason behind is that the interrupt might be provided by a gpio
controller, not probed when dm9000 is probed, and needing the probe
deferral mechanism to apply.

Currently, the interrupt is directly taken from resources. This patch
changes this to use the more generic platform_get_irq(), which handles
the deferral.

Moreover, since commit Fixes: 7085a740 ("drivers: platform: parse
IRQ flags from resources"), the interrupt trigger flags are honored in
platform_get_irq(), so remove the needless code in dm9000.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Acked-by: NMarcel Ziswiler <marcel@ziswiler.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: NSergei Ianovich <ynvich@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fix incorrect indexing of dev->dev_addr[] when copying the MAC address
of FMV-J182 at buf[5].
Signed-off-by: NKen Kawasaki <ken_kawasaki@nifty.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SW data field in descriptor can be used by software to hold private
data for the driver. As there are 4 words available for this purpose,
use separate macros to place it or retrieve the same to/from
descriptors. Also do type cast of data types accordingly.

Cc: Wingman Kwok <w-kwok2@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Grygorii Strashko <grygorii.strashko@ti.com>
CC: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename the pad to sw_data as per description of this field in the hardware
spec(refer sprugr9 from www.ti.com). Latest version of the document is
at http://www.ti.com/lit/ug/sprugr9h/sprugr9h.pdf and section 3.1
Host Packet Descriptor describes this field.

Define and use a constant for the size of sw_data field similar to
other fields in the struct for desc and document the sw_data field
in the header. As the sw_data is not touched by hw, it's type can be
changed to u32.

Rename the helpers to match with the updated dma desc field sw_data.

Cc: Wingman Kwok <w-kwok2@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Grygorii Strashko <grygorii.strashko@ti.com>
CC: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit 89907779 ("netcp: try to reduce type confusion in
descriptors") introduces a regression in Kernel 4.5-rc1 and it breaks
get/set_pad_info() functionality.

The TI NETCP driver uses pad0 and pad1 fields of knav_dma_desc to
store DMA/MEM buffer pointer and buffer size respectively. And in both
cases for Keystone 2 the pointer type size is 32 bit regardless of
LAPE enabled or not, because CONFIG_ARCH_DMA_ADDR_T_64BIT originally
is not expected to be defined.

Unfortunately, above commit changed buffer's pointers save/restore
code (get/set_pad_info()) and added intermediate conversation to u64
which works incorrectly on 32bit Keystone 2 and causes TI NETCP driver
crash in RX/TX path due to "Unable to handle kernel NULL pointer"
exception. This issue was reported and discussed in [1].

Hence, fix it by partially reverting above commit and restoring
get/set_pad_info() functionality as it was before.

[1] https://www.mail-archive.com/netdev@vger.kernel.org/msg95361.html
Cc: Wingman Kwok <w-kwok2@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
CC: David Laight <David.Laight@ACULAB.COM>
CC: Arnd Bergmann <arnd@arndb.de>
Reported-by: NFranklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PHY link state is not chaged in GENETv2 caused by the previous
commit 49f7a471 ("net: bcmgenet: Properly configure PHY to ignore
interrupt") was set to PHY_IGNORE_INTERRUPT in bcmgenet_mii_probe().

The internal PHY should use phy_mac_interrupt() when not in use
PHY_POLL. The statement for phy_mac_interrupt() has two conditions. The
first condition to check GENET_HAS_MDIO_INTR is not related PHY link
state, so this patch removes it.

Fixes: 49f7a471 ("net: bcmgenet: Properly configure PHY to ignore interrupt")
Signed-off-by: NJaedon Shin <jaedon.shin@gmail.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If we fail to update the PHY, we should print a warning and continue.
The current code to exit is buggy as it has not freed up the NIC
resources yet.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix bnxt_update_phy_setting() to check the correct parameters when
determining whether to update the PHY.  Requested line speed/duplex should
only be checked for forced speed mode.  This avoids unnecessary link
interruptions when loading the driver.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When shutting down the NIC, we shutdown async event processing before
freeing all the rings.  If there is a link change event during reset, the
driver may miss it and the link state may be incorrect after the NIC is
re-opened.  Poll the link at the end of __bnxt_open_nic() to get the
correct link status.

Signed-off-by Michael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The vpd strings are left justified, in a fixed length array, with possible
trailing white space and no NUL.  So fix them up before calling kstrto*().

This is a recent regression which causes cxgb3 to fail to load.

Fixes: e72c932d ("cxgb3: Convert simple_strtoul to kstrtox")
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Failure of kzalloc should cause the enclosing function
to return -ENOMEM, not -ENODEV.

Additionally, removed the following checkpatch warnings:
ERROR: spaces required around that '==' (ctx:VxV)
ERROR: space required before the open parenthesis '('
CHECK: Comparison to NULL could be written "!lp"
Signed-off-by: NAmitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When PVID is toggled off on a port member in a VLAN filtering bridge or
the PVID VLAN is deleted, make the port drop untagged packets. Reverse
the operation when PVID is toggled back on.

Set the PVID back to the default (1), when leaving the bridge so that
untagged traffic will be directed to the CPU.

Fixes: 56ade8fe ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When VLAN filtering is enabled on a bridge and PVID is deleted from a
bridge port, then untagged frames are not allowed to ingress into the
bridge from this port.

Add the Switch Port Acceptable Frame Types (SPAFT) register, which
configures the frame admittance of the port.

Fixes: 56ade8fe ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For error handling, dma_alloc_coherent's return value
needs to be checked, not argument.
Signed-off-by: NInsu Yun <wuninsu@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Counting rx packets for every CQE_RX in CQ irq handler is incorrect.
Synchronization is missing when multiple queues are receiving packets
simultaneously. Like transmit packet stats use HW stats here.

Also removed unused 'cqe_type' parameter in nicvf_rcv_pkt_handler().
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For secondary Qsets 'hw_tso' is not getting set as probe() returns
much earlier. Fixed it by moving silicon revision check.
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a interface is assigned morethan 8 queues and the logical interface
is toggled i.e down & up, additional queues or qsets are not initialized
as secondary qset count is being set to zero while tearing down.
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a VLAN device leaves a bridge its STP state is set to DISABLED,
which causes the hardware to discard any packets coming through the port
with this VLAN.

Fix that by setting STP state to FORWARDING when the device leaves its
bridge and allow traffic to be directed to CPU.

Fixes: 26f0e7fb ("mlxsw: spectrum: Add support for VLAN devices bridging")
Reported-by: NElad Raz <eladr@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MLXSW_PORT_MAX_PORTS represents the maximum number of local ports, which
is 65 for both ASICs (SwitchX-2 and Spectrum) supported by this driver.

Fixes: 93c1edb2 ("mlxsw: Introduce Mellanox switch driver core")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The cpsw-phy-sel driver supports only MII, RMII, and RGMII PHY modes,
and silently handled any other values as if MII was specified. In a
case where the PHY mode was incorrectly specified, or a bug elsewhere,
there would be no indication of a problem. If MII was the correct mode,
then this will go unnoticed, otherwise the symptom will be a failure
to transmit/receive data over the RMII/RGMII link.

Add a dev_warn() to make this condition obvious and provide a
breadcrumb to follow.

Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid Rivshin <drivshin@allworx.com>
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's forbidden to manually change dev->features in run-time. Currently, this is
done in the driver to make sure that GSO_UDP_TUNNEL is advertized only when
VXLAN tunnel is set. However, since the stack actually does features intersection
with hw_enc_features, we can safely revert to advertizing features early when
registering the netdevice.

Fixes: f4a1edd5 ('net/mlx4_en: Advertize encapsulation offloads [...]')
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

problem description:

The current code sets UAR page size equal to system page size.
The ConnectX-3 and ConnectX-3 Pro HWs require minimum 128 UAR pages.
The mlx4 kernel drivers are not loaded if there is less than 128 UAR pages.

solution:

Always set UAR page to 4KB. This allows more UAR pages if the OS
has PAGE_SIZE larger than 4KB. For example, PowerPC kernel use 64KB
system page size, with 4MB uar region, there are 4MB/2/64KB = 32
uars (half for uar, half for blueflame). This does not meet minimum 128
UAR pages requirement. With 4KB UAR page, there are 4MB/2/4KB = 512 uars
which meet the minimum requirement.

Note that only codes in mlx4_core that deal with firmware know that uar
page size is 4KB. Codes that deal with usr page in cq and qp context
(mlx4_ib, mlx4_en and part of mlx4_core) still have the same assumption
that uar page size equals to system page size.

Note that with this implementation, on 64KB system page size kernel, there
are 16 uars per system page but only one uars is used. The other 15
uars are ignored because of the above assumption.

Regarding SR-IOV, mlx4_core in hypervisor will set the uar page size
to 4KB and mlx4_core code in virtual OS will obtain the uar page size from
firmware.

Regarding backward compatibility in SR-IOV, if hypervisor has this new code,
the virtual OS must be updated. If hypervisor has old code, and the virtual
OS has this new code, the new code will be backward compatible with the
old code. If the uar size is big enough, this new code in VF continues to
work with 64 KB uar page size (on PowerPc kernel). If the uar size does not
meet 128 uars requirement, this new code not loaded in VF and print the same
error message as the old code in Hypervisor.
Signed-off-by: NHuy Nguyen <huyn@mellanox.com>
Reviewed-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PCI channel could go offline during reset due to EEH.  Don't bug on in
this case, the error is recoverable.

Fixes: f6bc11e4 ('net/mlx4_core: Enhance the catas flow to support device reset')
Signed-off-by: NDaniel Jurgens <danielj@mellanox.com>
Reviewed-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The error flow in procedure handle_existing_counter() is wrong.

The procedure should exit after encountering the error, not continue
as if everything is OK.

Fixes: 68230242 ('net/mlx4_core: Add port attribute when tracking counters')
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously, the shift value used for time-stamping was constant and didn't
depend on the HW chip frequency. Change that to take the frequency into account
and calculate the maximal value in cycles per wraparound of ten seconds. This
time slot was chosen since it gives a good accuracy in time synchronization.

Algorithm for shift value calculation:
 * Round up the maximal value in cycles to nearest power of two

 * Calculate maximal multiplier by division of all 64 bits set
   to above result

 * Then, invert the function clocksource_khz2mult() to get the shift from
   maximal mult value

Fixes: ec693d47 ('net/mlx4_en: Add HW timestamping (TS) support')
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Reviewed-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RdropOvflw counts overrun of HW buffer, therefore should
be used for rx_fifo_errors only.

Currently RdropOvflw counter is mistakenly also set into
rx_missed_errors and rx_over_errors too, which makes the
device total dropped packets accounting to show wrong results.

Fix that. Use it for rx_fifo_errors only.

Fixes: c27a02cd ('mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC')
Signed-off-by: NAmir Vadai <amir@vadai.me>
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

add new id (CONTEC C-NET(PC)C-100TX2)
Signed-off-by: NKen Kawasaki <ken_kawasaki@nifty.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current default tx ring size of 512 causes an extra page to be
allocated for the tx ring with only 1 entry in it.  Reduce it to
511.  The default rx ring size is also reduced to 511 to use less
memory by default.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tx push is supported for small packets to reduce DMA latency.  The
following bugs are fixed in this patch:

1. Fix the definition of the push BD which is different from the DMA BD.
2. The push buffer has to be zero padded to the next 64-bit word boundary
or tx checksum won't be correct.
3. Increase the tx push packet threshold to 164 bytes (192 bytes with the BD)
so that small tunneled packets are within the threshold.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

20G is not supported by production hardware and only the 40GbaseCR4 standard
is supported.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cleanup bnxt_probe_phy() to cleanly separate 2 code blocks for autoneg
on and off.  Autoneg flow control is possible only if autoneg is enabled.

In bnxt_get_settings(), Pause and Asym_Pause are always supported.
Only the advertisement bits change depending on the ethtool -A setting
in auto mode.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. Determine autoneg on|off setting from link_info->autoneg.  Using the
firmware returned setting can be misleading if autoneg is changed and
there hasn't been a phy update from the firmware.

2. If autoneg is disabled, link_info->autoneg should be set to 0 to
indicate both speed and flow control autoneg are disabled.

3. To enable autoneg flow control, speed autoneg must be enabled.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

EMAC could be disabled, while there is some sb_buff
in use. That buffers got lost for linux.

In order to reproduce run on device during active ethernet work:
    ifconfig eth0 down
Signed-off-by: NAlexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

EMAC reset internal tx ring pointer to zero at statup.
txbd_curr and txbd_dirty can be different from zero.
That cause ethernet transfer hang (no packets transmitted).

In order to reproduce, run on device:
    ifconfig eth0 down
    ifconfig eth0 up
Signed-off-by: NAlexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>