Fix the NACK check in ixgbevf_set_uc_addr_vf() for instances where
index != 0.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The pci_enable_msix_range() function returns a positive value of the
number of allocated vectors if it succeeds. On failure it returns
a negative error code. Return this code properly so that the error
message printed by the driver will show the actual error code instead of
being masked by -ENOMEM.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When we resume from an AER recovery with many active VFs, the PF sees
many spurious link up and link down events. Prevent this by delaying
link down for at least one second after the resume event.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If the fm10k interface is brought up, but the switch manager software is
not running, the driver will continuously request the lport map every
few seconds in the base driver watchdog routine. Eventually after
several minutes the switch mailbox Tx fifo will fill up and the mailbox
will timeout, resulting in a reset. This reset will appear as if for no
reason, and occurs regularly every few minutes until the switch manager
software is loaded.

Prevent this from happening by only requesting the lport map after we've
verified the switch mailbox is tx_ready. In order to simplify code logic
and reduce code duplication, implement this as a new function pointer
"mac.ops.request_lport_map" which the VF will not implement. Otherwise,
we have to duplicate the tx_ready check outside of
fm10k_get_host_state_generic, or re-implement most of
fm10k_get_host_state_generic in the pf version.

The resulting code is simpler and easier to understand, and prevents the
PF from continuously requesting lport map and filling the Tx fifo of
a switch mailbox that isn't ready.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Sometimes, a VF driver will lose PCIe address access, such as due to
a PF FLR event. In fm10k_detach_subtask, poll and check whether the
PCIe register space is active again and restore the device when it has.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If an FLR occurs, VF devices will be knocked out of bus master mode, and
the driver will be unable to recover from the reset properly, resulting
in malicious driver events and an infinite reset loop. In the normal
case, the bus master mode will already be enabled and this call will
essentially be a no-op. Since we're doing this every reset, it is
possible we could remove the other calls to pci_set_master() but it
seems not harmful to just leave them in place.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Continuing the effort to commonize the similar suspend/resume flows,
finish up by using the new fm10k_handle_suspand and fm10k_handle_resume
functions for the standard suspend/resume flow.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When a function level PCI reset is triggered using sysfs, it calls the
driver's .reset_notify error handler. Implement a handler based on the
now split fm10k_prepare_for_reset and fm10k_handle_reset functions, so
that we fully reset the driver when the PCI function level reset occurs.
This also ensures the reset is handled in a clean way by first disabling
all the driver bits first and then restoring them after the function
reset. Previously the stack simply performed a blind function reset and
our driver didn't take any part in the process.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Now that we have extracted the necessary steps for a split
suspend/resume flow, re-use these functions instead of using the current
open coded flow. This ensures that we don't miss any steps. It also
ensures that we have the correct driver states set.

Since we'll be handling all of the reset flow ourselves, we no longer
need to request a reset in the io_slot_reset() function.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Implement fm10k_prepare_suspend and fm10k_handle_resume functions which
abstract around the now existing fm10k_prepare_for_reset and
fm10k_handle_reset. The new functions also handle stopping the service
task, which is something that the original re-init flow does not need.

Every other location that does a suspend/resume type flow is expected to
use these functions, because otherwise they may have conflicts with the
running watchdog routines. This also has the effect of preventing
possible surprise remove events during handling of FLR events and PCIe
errors.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There are several flows in the driver which perform the similar function
of tearing down software and restoring software to recover from certain
errors or PCIe events, including:

  * fm10k_reinit
  * fm10k_suspend/resume
  * fm10k_io_error_detected/fm10k_io_resume

In addition, we want to implement a .reset_notify() handler as well
which will also perform similar function.

Rework how the driver codes reset and resume flows by separating out the
reinit logic into two functions "fm10k_prepare_for_reset" and
"fm10k_handle_reset". This first step will allow us to re-use this
functionality in the similar blocks of code instead of re-coding the
same sequence of events slightly different.

The end result should be more maintainable and correct, fixing several
inconsistencies with the work flow.

The new functions expect to take the rtnl_lock() themselves, and it does
have the unfortunate side effect of having the reinit flow take then
release then take the rtnl_lock. However, this minor downside is
out weighted by the benefits of code reduction and reducing needless
difference between these flows.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

It turns out that sometimes during a reset the Tx queues will be
temporarily stuck longer than .stop_hw() expects. Work around this issue
by attempting to .stop_hw() first. If it tails, wait a number of
attempts until the Tx queues appear to be drained. After this, attempt
stop_hw() again. This ensures that we avoid waiting if we don't need to,
such as during the first initialization of a VF, and give the proper
amount of time necessary to recover from most situations. It is possible
that the hardware is actually stuck. For PFs, this is usually fixed by
a datapath reset. Unfortunately the VF cannot request a similar reset
for itself.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When stop_hw() routine fails with FM10K_ERR_REQUESTS_PENDING, this
indicates that the Tx or Rx queues did not shutdown within the time
limit. Print a more suitable message at the dev_info level instead of
dev_err.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A while ago, an additional check for the switch being ready was added to
reset_hw. A recent refactor accidentally made this check return an error
code on failure which caused fm10k_probe to fail when the switch wasn't
brought up first. The original reasoning for the check was to prevent
additional data path reset when the fabric wasn't ready yet. However,
there isn't a compelling reason to keep the check, as the data path
reset will restore hardware to a known good state. Remove the check and
perform the data path reset regardless of the switch manager state.

An alternative fix is to return FM10K_SUCCESS instead, and bypass the
actual data path reset. This should be fine as we will perform
a reset_hw once the switch is active. However, since data path reset
will reset many parts of the hardware it seems better to just perform
the reset regardless of switch state.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Don't report FM10K_ERR_REQUESTS_PENDING when we fail to disable queues
within the timeout. This can occur due to a hardware Tx hang, or when
the switch ethernet fabric is resetting while we are transmitting
traffic. It can sometimes take up to 500ms before the Tx DMA engine
gives up. Instead, just skip the DMA engine check and perform
a data-path reset anyways. Add a statistic counter to keep track of the
number of resets occurring while we have pending DMA on the rings.

In order to prevent having to re-assign err to 0, re-order the
last few items of the reset_hw_pf function so that we don't perform
"return err" at the end.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When a data path reset is initiated, write control to the PCIE_GMBX is
yanked from the switch manager. The switch manager writes to this
register to clear mailbox global interrupt bits as part of its mailbox
interrupt handling routine. When the device recovers from the data path
reset and these bits are not cleared, it will prevent future mailbox
global interrupts from being triggered. Upon confirming that the device
has exited from a data path reset, clear these bits to ensure the proper
functioning of the mailbox global interrupt.
Signed-off-by: NNgai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Also prevent updating stats while the interface is down. If we're
already updating stats, just return doing nothing. When we take the
device down, block stat updates until we come back up. This ensures that
we avoid tearing down rings when we're updating statistics, and prevents
updating statistics until we're up.

We can't re-use the __FM10K_DOWN for this because it wouldn't prevent
multiple threads from accessing statistics. Neither does it prevent the
case where we start updating stats and then start going down in another
thread.

The fm10k_get_stats64 is except from this, because it has a completely
different flow which does not suffer from the same issues as
fm10k_update_stats might.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

It's currently possible for fm10k_update_stats to be called during the
window when we go down and the rings are removed. This can result in
a null pointer dereference. In fm10k_get_stats64 we work around this by
using ACCESS_ONCE and a null pointer check inside the loop. Use this
same flow in the fm10k_update_stats to avoid the potential null pointer.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Return early from fm10k_down() when we are already down, since that
means another thread is either already finished or has started going
down, so shouldn't conflict with them.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Some comments weren't updated to reflect the renaming of ndo's and the
change of arguments.
Signed-off-by: NSabrina Dubroca <sd@queasysnail.net>
Acked-by: NAlexander Duyck <aduyck@mirantis.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some platforms, syncing a buffer for DMA is expensive. Rather than
sync the whole 2K receive buffer, only synchronise the length of the
frame, which will typically be the MTU, or a much smaller TCP ACK.

For an IMX6Q, this gives around 6% increased TCP receive performance,
which is cache operations bound and reduces CPU load for TCP transmit.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When setting spoofing, both VLAN and MAC need to be set together.
This change resolves an issue where MAC-VLANs on the VF fail to pass
traffic due to spoofed packets.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update ixgbe_ethtool_get_ts_info() to show that x550 supports hardware
timestamping of all packets.
Reported-by: NGuy Harris <guy@alum.mit.edu>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

alloc_workqueue replaces deprecated create_workqueue().

A dedicated workqueue has been used since the workitem (viz
fm10k_service_task, which manages and runs other subtasks) is involved in
normal device operation and requires forward progress under memory
pressure.

create_workqueue has been replaced with alloc_workqueue with max_active
as 0 since there is no need for throttling the number of active work
items.

Since network devices may be used in memory reclaim path,
WQ_MEM_RECLAIM has been set to guarantee forward progress.

flush_workqueue is unnecessary since destroy_workqueue() itself calls
drain_workqueue() which flushes repeatedly till the workqueue
becomes empty. Hence the call to flush_workqueue() has been dropped.
Signed-off-by: NBhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Properly stop the extra workqueue items and ensure that we resume
cleanly. This is better than using igb_ptp_init and igb_ptp_stop since
these functions destroy the PHC device, which will cause other problems
if we do so. Since igb_ptp_reset now re-schedules the work-queue item we
don't need an equivalent igb_ptp_resume in the resume workflow.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Make igb_ptp_stop take advantage of this new function to reduce code
duplication.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Modify igb_ptp_init to take advantage of igb_ptp_reset, and remove
duplicated work that was occurring in both igb_ptp_reset and
igb_ptp_init.

In total, resetting the TSAUXC register, and resetting the system time
both happen in igb_ptp_reset already. igb_ptp_reset now also takes care
of starting the delayed work item for overflow checks, as well.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Don't continue to use complex MAC type checks for handling various cases
where we have overflow check code. Make this code more obvious by
introducing a flag which is enabled for hardware that needs these
checks.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Upcoming patches will introduce new PTP specific flags. To avoid
cluttering the normal flags variable, introduce PTP specific "ptp_flags"
variable for this purpose, and move IGB_FLAG_PTP to become
IGB_PTP_ENABLED.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

For u32 classifier filters, avoid overwriting existing filter
in a hardware location without removing it first, to clean up
inconsistencies due to duplicate values for filter location.

Verified with the following filters:

Create child hash tables:
	handle 1: u32 divisor 1
	handle 2: u32 divisor 1

Link to the child hash table from parent hash table:
	handle 800:0:11 u32 ht 800: link 1: \
	offset at 0 mask 0f00 shift 6 plus 0 eat \
	match ip protocol 6 ff match ip dst 15.0.0.1/32

	handle 800:0:12 u32 ht 800: link 2: \
	offset at 0 mask 0f00 shift 6 plus 0 eat \
	match ip protocol 17 ff match ip dst 16.0.0.1/32

Add filter into child hash table:
	handle 1:0:3 u32 ht 1: \
	match tcp src 22 ffff action drop

Add another filter to the same location:
	handle 2:0:3 u32 ht 2: \
	match tcp src 33 ffff action drop
Signed-off-by: NAmritha Nambiar <amritha.nambiar@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

On deleting filters which are links to a child hash table, the filters
in the child hash table must be cleared from the hardware if there
is no link between the parent and child hash table.

Verified with the following filters:

Create a child hash table:
	handle 1: u32 divisor 1

Link to the child hash table from parent hash table:
	handle 800:0:10 u32 ht 800: link 1: \
	offset at 0 mask 0f00 shift 6 plus 0 eat \
	match ip protocol 6 ff match ip dst 15.0.0.1/32

Add filters into child hash table:
	handle 1:0:2 u32 ht 1: \
	match tcp src 22 ffff action drop
        handle 1:0:3 u32 ht 1: \
        match tcp src 33 ffff action drop

Delete link filter from parent hash table:
	handle 800:0:10 u32
Signed-off-by: NAmritha Nambiar <amritha.nambiar@intel.com>
Acked-by: NSridhar Samudrala <sridhar.samudrala@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Users report that under VMWare, er32(TIMINCA) returns zero.
This causes division by zero at init time as follows:

 ==>       incvalue = er32(TIMINCA) & E1000_TIMINCA_INCVALUE_MASK;
           for (i = 0; i < E1000_MAX_82574_SYSTIM_REREADS; i++) {
                   /* latch SYSTIMH on read of SYSTIML */
                   systim_next = (cycle_t)er32(SYSTIML);
                   systim_next |= (cycle_t)er32(SYSTIMH) << 32;

                   time_delta = systim_next - systim;
                   temp = time_delta;
 ====>             rem = do_div(temp, incvalue);

This change makes kernel survive this, and users report that
NIC does work after this change.

Since on real hardware incvalue is never zero, this should not affect
real hardware use case.
Signed-off-by: NDenys Vlasenko <dvlasenk@redhat.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The index calculated when looping through the indir array passed to
fm10k_write_reta was incorrectly calculated as the first part i needs to
be multiplied by 4.

Fixes: 0cfea7a65738 ("fm10k: fix possible null pointer deref after kcalloc", 2016-04-13)
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

While reviewing the i40e driver changes to support page based receive I
realized that I had overlooked the fact that the fm10k hardware required a
512 byte alignment for Rx buffers.  This patch is meant to address that by
changing the alignment for Rx buffers to 512 bytes instead of allowing it
to be L1 cache aligned.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The FM10K_MAX_DATA_PER_TXD is really just using a bitshift as a power of
2 operation in an efficient manner. We shouldn't represent this as a BIT()
because that obscures the intention of the operation.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Now ixgbevf_write/read_posted_mbx use -IXGBE_ERR_MBX as the initiative
return value, but it's incorrect, cause in ixgbevf_vlan_rx_add_vid(),
it use err == IXGBE_ERR_MBX, the err returned from mac.ops.set_vfta,
and in ixgbevf_set_vfta_vf, it return from write/read_posted. so we
should initialize err with IXGBE_ERR_MBX, instead of -IXGBE_ERR_MBX.

With this fix, the other functions that called it also can work well,
cause they only care about if err is 0 or not.
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The bit in the e1000 driver that mentions explicitly that the hardware
has no support for separate RX/TX VLAN accel toggling rings true for
e1000e as well, and thus both NETIF_F_HW_VLAN_CTAG_RX and
NETIF_F_HW_VLAN_CTAG_TX need to be kept in sync.

Revert a portion of commit 889ad456 ("e1000e: keep VLAN interfaces
functional after rxvlan off") since keeping the bits in sync resolves
the original issue.
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

I've got a bug report about an e1000e interface, where a VLAN interface is
set up on top of it:

$ ip link add link ens1f0 name ens1f0.99 type vlan id 99
$ ip link set ens1f0 up
$ ip link set ens1f0.99 up
$ ip addr add 192.168.99.92 dev ens1f0.99

At this point, I can ping another host on vlan 99, ip 192.168.99.91.
However, if I do the following:

$ ethtool -K ens1f0 rxvlan off

Then no traffic passes on ens1f0.99. It comes back if I toggle rxvlan on
again. I'm not sure if this is actually intended behavior, or if there's a
lack of software VLAN stripping fallback, or what, but things continue to
work if I simply don't call e1000e_vlan_strip_disable() if there are
active VLANs (plagiarizing a function from the e1000 driver here) on the
interface.

Also slipped a related-ish fix to the kerneldoc text for
e1000e_vlan_strip_disable here...
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>