The link state and exception interrupts may be masked when we probe.
The firmware should in theory prevent sending (and automasking) those
interrupts if the device is disabled, but if my reading of the FW code
is correct there are firmwares out there with race conditions in this
area.  The interrupt may also be masked if previous driver which used
the device was malfunctioning and we didn't load the FW (there is no
other good way to comprehensively reset the PF).

Note that FW unmasks the data interrupts by itself when vNIC is
enabled, such helpful operation is not performed for LSC/EXN interrupts.

Always unmask the auxiliary interrupts after request_irq().  On the
remove path add missing PCI write flush before free_irq().

Fixes: 4c352362 ("net: add driver for Netronome NFP4000/NFP6000 NIC VFs")
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A vlan device with vid 0 is allow to creat by not able to be fully
cleaned up by unregister_vlan_dev() which checks for vlan_id!=0.

Also, VLAN 0 is probably not a valid number and it is kinda
"reserved" for HW accelerating devices, but it is probably too
late to reject it from creation even if makes sense. Instead,
just remove the check in unregister_vlan_dev().
Reported-by: NDmitry Vyukov <dvyukov@google.com>
Fixes: ad1afb00 ("vlan_dev: VLAN 0 should be treated as "no vlan tag" (802.1p packet)")
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2018-01-09' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for 4.15

Hopefully the last set of fixes for 4.15.

iwlwifi

* fix DMA mapping regression since v4.14

wcn36xx

* fix dynamic power save which has been broken since the driver was commited
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If one of the child devices is missing the of_mdiobus_register_phy()
call will return -ENODEV. When a missing device is encountered the
registration of the remaining PHYs is stopped and the MDIO bus will
fail to register. Propagate all errors except ENODEV to avoid it.
Signed-off-by: NMadalin Bucur <madalin.bucur@nxp.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

gcc-8 reports

net/caif/caif_usb.c: In function 'cfusbl_device_notify':
./include/linux/string.h:245:9: warning: '__builtin_strncpy' output may
be truncated copying 15 bytes from a string of length 15
[-Wstringop-truncation]

The compiler require that the input param 'len' of strncpy() should be
greater than the length of the src string, so that '\0' is copied as
well. We can just use strlcpy() to avoid this warning.
Signed-off-by: NXiongfeng Wang <xiongfeng.wang@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NKornilios Kourtis <kou@zurich.ibm.com>
Acked-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

set_fipers() calling should be protected by spinlock in
case that any interrupt breaks related registers setting
and the function we expect. This patch is to move set_fipers()
to spinlock protecting area in ptp_gianfar_adjtime().
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Marcelo Ricardo Leitner says:

====================
sctp: Some sockopt optlen fixes

Hangbin Liu reported that some SCTP sockopt are allowing the user to get
the kernel to allocate really large buffers by not having a ceiling on
optlen.

This patchset address this issue (in patch 2), replace an GFP_ATOMIC
that isn't needed and avoid calculating the option size multiple times
in some setsockopt.
====================
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some sockopt handling functions were calculating the length of the
buffer to be written to userspace and then calculating it again when
actually writing the buffer, which could lead to some write not using
an up-to-date length.

This patch updates such places to just make use of the len variable.

Also, replace some sizeof(type) to sizeof(var).
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hangbin Liu reported that some sockopt calls could cause the kernel to log
a warning on memory allocation failure if the user supplied a large optlen
value. That is because some of them called memdup_user() without a ceiling
on optlen, allowing it to try to allocate really large buffers.

This patch adds a ceiling by limiting optlen to the maximum allowed that
would still make sense for these sockopt.
Reported-by: NHangbin Liu <haliu@redhat.com>
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

So replace it with GFP_USER and also add __GFP_NOWARN.
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf 2018-01-09

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) Prevent out-of-bounds speculation in BPF maps by masking the
   index after bounds checks in order to fix spectre v1, and
   add an option BPF_JIT_ALWAYS_ON into Kconfig that allows for
   removing the BPF interpreter from the kernel in favor of
   JIT-only mode to make spectre v2 harder, from Alexei.

2) Remove false sharing of map refcount with max_entries which
   was used in spectre v1, from Daniel.

3) Add a missing NULL psock check in sockmap in order to fix
   a race, from John.

4) Fix test_align BPF selftest case since a recent change in
   verifier rejects the bit-wise arithmetic on pointers
   earlier but test_align update was missing, from Alexei.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The BPF interpreter has been used as part of the spectre 2 attack CVE-2017-5715.

A quote from goolge project zero blog:
"At this point, it would normally be necessary to locate gadgets in
the host kernel code that can be used to actually leak data by reading
from an attacker-controlled location, shifting and masking the result
appropriately and then using the result of that as offset to an
attacker-controlled address for a load. But piecing gadgets together
and figuring out which ones work in a speculation context seems annoying.
So instead, we decided to use the eBPF interpreter, which is built into
the host kernel - while there is no legitimate way to invoke it from inside
a VM, the presence of the code in the host kernel's text section is sufficient
to make it usable for the attack, just like with ordinary ROP gadgets."

To make attacker job harder introduce BPF_JIT_ALWAYS_ON config
option that removes interpreter from the kernel in favor of JIT-only mode.
So far eBPF JIT is supported by:
x64, arm64, arm32, sparc64, s390, powerpc64, mips64

The start of JITed program is randomized and code page is marked as read-only.
In addition "constant blinding" can be turned on with net.core.bpf_jit_harden

v2->v3:
- move __bpf_prog_ret0 under ifdef (Daniel)

v1->v2:
- fix init order, test_bpf and cBPF (Daniel's feedback)
- fix offloaded bpf (Jakub's feedback)
- add 'return 0' dummy in case something can invoke prog->bpf_func
- retarget bpf tree. For bpf-next the patch would need one extra hunk.
  It will be sent when the trees are merged back to net-next

Considered doing:
  int bpf_jit_enable __read_mostly = BPF_EBPF_JIT_DEFAULT;
but it seems better to land the patch as-is and in bpf-next remove
bpf_jit_enable global variable from all JITs, consolidate in one place
and remove this jit_init() function.
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

In addition to commit b2157399 ("bpf: prevent out-of-bounds
speculation") also change the layout of struct bpf_map such that
false sharing of fast-path members like max_entries is avoided
when the maps reference counter is altered. Therefore enforce
them to be placed into separate cachelines.

pahole dump after change:

  struct bpf_map {
        const struct bpf_map_ops  * ops;                 /*     0     8 */
        struct bpf_map *           inner_map_meta;       /*     8     8 */
        void *                     security;             /*    16     8 */
        enum bpf_map_type          map_type;             /*    24     4 */
        u32                        key_size;             /*    28     4 */
        u32                        value_size;           /*    32     4 */
        u32                        max_entries;          /*    36     4 */
        u32                        map_flags;            /*    40     4 */
        u32                        pages;                /*    44     4 */
        u32                        id;                   /*    48     4 */
        int                        numa_node;            /*    52     4 */
        bool                       unpriv_array;         /*    56     1 */

        /* XXX 7 bytes hole, try to pack */

        /* --- cacheline 1 boundary (64 bytes) --- */
        struct user_struct *       user;                 /*    64     8 */
        atomic_t                   refcnt;               /*    72     4 */
        atomic_t                   usercnt;              /*    76     4 */
        struct work_struct         work;                 /*    80    32 */
        char                       name[16];             /*   112    16 */
        /* --- cacheline 2 boundary (128 bytes) --- */

        /* size: 128, cachelines: 2, members: 17 */
        /* sum members: 121, holes: 1, sum holes: 7 */
  };

Now all entries in the first cacheline are read only throughout
the life time of the map, set up once during map creation. Overall
struct size and number of cachelines doesn't change from the
reordering. struct bpf_map is usually first member and embedded
in map structs in specific map implementations, so also avoid those
members to sit at the end where it could potentially share the
cacheline with first map values e.g. in the array since remote
CPUs could trigger map updates just as well for those (easily
dirtying members like max_entries intentionally as well) while
having subsequent values in cache.

Quoting from Google's Project Zero blog [1]:

  Additionally, at least on the Intel machine on which this was
  tested, bouncing modified cache lines between cores is slow,
  apparently because the MESI protocol is used for cache coherence
  [8]. Changing the reference counter of an eBPF array on one
  physical CPU core causes the cache line containing the reference
  counter to be bounced over to that CPU core, making reads of the
  reference counter on all other CPU cores slow until the changed
  reference counter has been written back to memory. Because the
  length and the reference counter of an eBPF array are stored in
  the same cache line, this also means that changing the reference
  counter on one physical CPU core causes reads of the eBPF array's
  length to be slow on other physical CPU cores (intentional false
  sharing).

While this doesn't 'control' the out-of-bounds speculation through
masking the index as in commit b2157399, triggering a manipulation
of the map's reference counter is really trivial, so lets not allow
to easily affect max_entries from it.

Splitting to separate cachelines also generally makes sense from
a performance perspective anyway in that fast-path won't have a
cache miss if the map gets pinned, reused in other progs, etc out
of control path, thus also avoids unintentional false sharing.

  [1] https://googleprojectzero.blogspot.ch/2018/01/reading-privileged-memory-with-side.htmlSigned-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>

In the current code, when creating a new fib6 table, tb6_root.leaf gets
initialized to net->ipv6.ip6_null_entry.
If a default route is being added with rt->rt6i_metric = 0xffffffff,
fib6_add() will add this route after net->ipv6.ip6_null_entry. As
null_entry is shared, it could cause problem.

In order to fix it, set fn->leaf to NULL before calling
fib6_add_rt2node() when trying to add the first default route.
And reset fn->leaf to null_entry when adding fails or when deleting the
last default route.

syzkaller reported the following issue which is fixed by this commit:

WARNING: suspicious RCU usage
4.15.0-rc5+ #171 Not tainted
-----------------------------
net/ipv6/ip6_fib.c:1702 suspicious rcu_dereference_protected() usage!

other info that might help us debug this:

rcu_scheduler_active = 2, debug_locks = 1
4 locks held by swapper/0/0:
 #0:  ((&net->ipv6.ip6_fib_timer)){+.-.}, at: [<00000000d43f631b>] lockdep_copy_map include/linux/lockdep.h:178 [inline]
 #0:  ((&net->ipv6.ip6_fib_timer)){+.-.}, at: [<00000000d43f631b>] call_timer_fn+0x1c6/0x820 kernel/time/timer.c:1310
 #1:  (&(&net->ipv6.fib6_gc_lock)->rlock){+.-.}, at: [<000000002ff9d65c>] spin_lock_bh include/linux/spinlock.h:315 [inline]
 #1:  (&(&net->ipv6.fib6_gc_lock)->rlock){+.-.}, at: [<000000002ff9d65c>] fib6_run_gc+0x9d/0x3c0 net/ipv6/ip6_fib.c:2007
 #2:  (rcu_read_lock){....}, at: [<0000000091db762d>] __fib6_clean_all+0x0/0x3a0 net/ipv6/ip6_fib.c:1560
 #3:  (&(&tb->tb6_lock)->rlock){+.-.}, at: [<000000009e503581>] spin_lock_bh include/linux/spinlock.h:315 [inline]
 #3:  (&(&tb->tb6_lock)->rlock){+.-.}, at: [<000000009e503581>] __fib6_clean_all+0x1d0/0x3a0 net/ipv6/ip6_fib.c:1948

stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.15.0-rc5+ #171
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 <IRQ>
 __dump_stack lib/dump_stack.c:17 [inline]
 dump_stack+0x194/0x257 lib/dump_stack.c:53
 lockdep_rcu_suspicious+0x123/0x170 kernel/locking/lockdep.c:4585
 fib6_del+0xcaa/0x11b0 net/ipv6/ip6_fib.c:1701
 fib6_clean_node+0x3aa/0x4f0 net/ipv6/ip6_fib.c:1892
 fib6_walk_continue+0x46c/0x8a0 net/ipv6/ip6_fib.c:1815
 fib6_walk+0x91/0xf0 net/ipv6/ip6_fib.c:1863
 fib6_clean_tree+0x1e6/0x340 net/ipv6/ip6_fib.c:1933
 __fib6_clean_all+0x1f4/0x3a0 net/ipv6/ip6_fib.c:1949
 fib6_clean_all net/ipv6/ip6_fib.c:1960 [inline]
 fib6_run_gc+0x16b/0x3c0 net/ipv6/ip6_fib.c:2016
 fib6_gc_timer_cb+0x20/0x30 net/ipv6/ip6_fib.c:2033
 call_timer_fn+0x228/0x820 kernel/time/timer.c:1320
 expire_timers kernel/time/timer.c:1357 [inline]
 __run_timers+0x7ee/0xb70 kernel/time/timer.c:1660
 run_timer_softirq+0x4c/0xb0 kernel/time/timer.c:1686
 __do_softirq+0x2d7/0xb85 kernel/softirq.c:285
 invoke_softirq kernel/softirq.c:365 [inline]
 irq_exit+0x1cc/0x200 kernel/softirq.c:405
 exiting_irq arch/x86/include/asm/apic.h:540 [inline]
 smp_apic_timer_interrupt+0x16b/0x700 arch/x86/kernel/apic/apic.c:1052
 apic_timer_interrupt+0xa9/0xb0 arch/x86/entry/entry_64.S:904
 </IRQ>
Reported-by: Nsyzbot <syzkaller@googlegroups.com>
Fixes: 66f5d6ce ("ipv6: replace rwlock with rcu and spinlock in fib6_table")
Signed-off-by: NWei Wang <weiwan@google.com>
Acked-by: NMartin KaFai Lau <kafai@fb.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sergei Shtylyov says:

====================
Ether fixes for the SolutionEngine771x boards

Here's the series of 2 patches against Linus' repo. This series should
(hoplefully) fix the Ether support on the SolutionEngine771x boards...

[1/2] SolutionEngine771x: fix Ether platform data
[2/2] SolutionEngine771x: add Ether TSU resource
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After the  Ether platform data is fixed, the driver probe() method would
still fail since the 'struct sh_eth_cpu_data' corresponding  to SH771x
indicates the presence of TSU but the memory resource for it is absent.
Add the missing TSU resource  to both Ether devices and fix the harmless
off-by-one error in the main memory resources, while at it...

Fixes: 4986b996 ("net: sh_eth: remove the SH_TSU_ADDR")
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 'sh_eth' driver's probe() method would fail  on the SolutionEngine7710
board and crash on SolutionEngine7712 board  as the platform code is
hopelessly behind the driver's platform data --  it passes the PHY address
instead of 'struct sh_eth_plat_data *'; pass the latter to the driver in
order to fix the bug...

Fixes: 71557a37 ("[netdrvr] sh_eth: Add SH7619 support")
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the following 'make htmldocs' complaint:

Documentation/networking/msg_zerocopy.rst:: WARNING: document isn't included in any toctree.
Signed-off-by: NMike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 8f659a03 ("net: ipv4: fix for a race condition in
raw_sendmsg") fixed the issue of possibly inconsistent ->hdrincl handling
due to concurrent updates by reading this bit-field member into a local
variable and using the thus stabilized value in subsequent tests.

However, aforementioned commit also adds the (correct) comment that

  /* hdrincl should be READ_ONCE(inet->hdrincl)
   * but READ_ONCE() doesn't work with bit fields
   */

because as it stands, the compiler is free to shortcut or even eliminate
the local variable at its will.

Note that I have not seen anything like this happening in reality and thus,
the concern is a theoretical one.

However, in order to be on the safe side, emulate a READ_ONCE() on the
bit-field by doing it on the local 'hdrincl' variable itself:

	int hdrincl = inet->hdrincl;
	hdrincl = READ_ONCE(hdrincl);

This breaks the chain in the sense that the compiler is not allowed
to replace subsequent reads from hdrincl with reloads from inet->hdrincl.

Fixes: 8f659a03 ("net: ipv4: fix for a race condition in raw_sendmsg")
Signed-off-by: NNicolai Stange <nstange@suse.de>
Reviewed-by: NStefano Brivio <sbrivio@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

gcc-8 reports

net/caif/caif_dev.c: In function 'caif_enroll_dev':
./include/linux/string.h:245:9: warning: '__builtin_strncpy' output may
be truncated copying 15 bytes from a string of length 15
[-Wstringop-truncation]

net/caif/cfctrl.c: In function 'cfctrl_linkup_request':
./include/linux/string.h:245:9: warning: '__builtin_strncpy' output may
be truncated copying 15 bytes from a string of length 15
[-Wstringop-truncation]

net/caif/cfcnfg.c: In function 'caif_connect_client':
./include/linux/string.h:245:9: warning: '__builtin_strncpy' output may
be truncated copying 15 bytes from a string of length 15
[-Wstringop-truncation]

The compiler require that the input param 'len' of strncpy() should be
greater than the length of the src string, so that '\0' is copied as
well. We can just use strlcpy() to avoid this warning.
Signed-off-by: NXiongfeng Wang <xiongfeng.wang@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use AF_INET6 instead of AF_INET in IPv6-related code path
Signed-off-by: NAndrii Vladyka <tulup@mail.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Frag and UDP handling fixes in i40e driver, from Amritha Nambiar and
    Alexander Duyck.

 2) Undo unintentional UAPI change in netfilter conntrack, from Florian
    Westphal.

 3) Revert a change to how error codes are returned from
    dev_get_valid_name(), it broke some apps.

 4) Cannot cache routes for ipv6 tunnels in the tunnel is ipv4/ipv6
    dual-stack. From Eli Cooper.

 5) Fix missed PMTU updates in geneve, from Xin Long.

 6) Cure double free in macvlan, from Gao Feng.

 7) Fix heap out-of-bounds write in rds_message_alloc_sgs(), from
    Mohamed Ghannam.

 8) FEC bug fixes from FUgang Duan (mis-accounting of dev_id, missed
    deferral of probe when the regulator is not ready yet).

 9) Missing DMA mapping error checks in 3c59x, from Neil Horman.

10) Turn off Broadcom tags for some b53 switches, from Florian Fainelli.

11) Fix OOPS when get_target_net() is passed an SKB whose NETLINK_CB()
    isn't initialized. From Andrei Vagin.

12) Fix crashes in fib6_add(), from Wei Wang.

13) PMTU bug fixes in SCTP from Marcelo Ricardo Leitner.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (56 commits)
  sh_eth: fix TXALCR1 offsets
  mdio-sun4i: Fix a memory leak
  phylink: mark expected switch fall-throughs in phylink_mii_ioctl
  sctp: fix the handling of ICMP Frag Needed for too small MTUs
  sctp: do not retransmit upon FragNeeded if PMTU discovery is disabled
  xen-netfront: enable device after manual module load
  bnxt_en: Fix the 'Invalid VF' id check in bnxt_vf_ndo_prep routine.
  bnxt_en: Fix population of flow_type in bnxt_hwrm_cfa_flow_alloc()
  sh_eth: fix SH7757 GEther initialization
  net: fec: free/restore resource in related probe error pathes
  uapi/if_ether.h: prevent redefinition of struct ethhdr
  ipv6: fix general protection fault in fib6_add()
  RDS: null pointer dereference in rds_atomic_free_op
  sh_eth: fix TSU resource handling
  net: stmmac: enable EEE in MII, GMII or RGMII only
  rtnetlink: give a user socket to get_target_net()
  MAINTAINERS: Update my email address.
  can: ems_usb: improve error reporting for error warning and error passive
  can: flex_can: Correct the checking for frame length in flexcan_start_xmit()
  can: gs_usb: fix return value of the "set_bittiming" callback
  ...

Pull rdma fixes from Doug Ledford:

 - One line fix to mlx4 error flow (same as mlx5 fix in last pull
   request, just in the mlx4 driver)

 - Fix a race condition in the IPoIB driver. This patch is larger than
   just a one line fix, but resolves a race condition in a fairly
   straight forward manner

 - Fix a locking issue in the RDMA netlink code. This patch is also
   larger than I would like for a late -rc. It has, however, had a week
   to bake in the rdma tree prior to this pull request

 - One line fix to fix granting remote machine access to memory that
   they don't need and shouldn't have

 - One line fix to correct the fact that our sgid/dgid pair is swapped
   from what you would expect when receiving an incoming connection
   request

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
  IB/srpt: Fix ACL lookup during login
  IB/srpt: Disable RDMA access by the initiator
  RDMA/netlink: Fix locking around __ib_get_device_by_index
  IB/ipoib: Fix race condition in neigh creation
  IB/mlx4: Fix mlx4_ib_alloc_mr error flow

Under speculation, CPUs may mis-predict branches in bounds checks. Thus,
memory accesses under a bounds check may be speculated even if the
bounds check fails, providing a primitive for building a side channel.

To avoid leaking kernel data round up array-based maps and mask the index
after bounds check, so speculated load with out of bounds index will load
either valid value from the array or zero from the padded area.

Unconditionally mask index for all array types even when max_entries
are not rounded to power of 2 for root user.
When map is created by unpriv user generate a sequence of bpf insns
that includes AND operation to make sure that JITed code includes
the same 'index & index_mask' operation.

If prog_array map is created by unpriv user replace
  bpf_tail_call(ctx, map, index);
with
  if (index >= max_entries) {
    index &= map->index_mask;
    bpf_tail_call(ctx, map, index);
  }
(along with roundup to power 2) to prevent out-of-bounds speculation.
There is secondary redundant 'if (index >= max_entries)' in the interpreter
and in all JITs, but they can be optimized later if necessary.

Other array-like maps (cpumap, devmap, sockmap, perf_event_array, cgroup_array)
cannot be used by unpriv, so no changes there.

That fixes bpf side of "Variant 1: bounds check bypass (CVE-2017-5753)" on
all architectures with and without JIT.

v2->v3:
Daniel noticed that attack potentially can be crafted via syscall commands
without loading the program, so add masking to those paths as well.
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NJohn Fastabend <john.fastabend@gmail.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Pull x86 platform driver fix from Darren Hart:
 "Address a wmi initcall ordering race resulting in a difficult to
  reproduce boot failure"

* tag 'platform-drivers-x86-v4.15-4' of git://git.infradead.org/linux-platform-drivers-x86:
  platform/x86: wmi: Call acpi_wmi_init() later

The  TXALCR1 offsets are incorrect in the register offset tables, most
probably due to copy&paste error.  Luckily, the driver never uses this
register. :-)

Fixes: 4a55530f ("net: sh_eth: modify the definitions of register")
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the probing of the regulator is deferred, the memory allocated by
'mdiobus_alloc_size()' will be leaking.
It should be freed before the next call to 'sun4i_mdio_probe()' which will
reallocate it.

Fixes: 4bdcb1dd ("net: Add MDIO bus driver for the Allwinner EMAC")
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

Addresses-Coverity-ID: 1463447 ("Missing break in switch")
Signed-off-by: NGustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Marcelo Ricardo Leitner says:

====================
SCTP PMTU discovery fixes

This patchset fixes 2 issues with PMTU discovery that can lead to flood
of retransmissions.
The first patch fixes the issue for when PMTUD is disabled by the
application, while the second fixes it for when its enabled.

Please consider these to stable.
====================
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

syzbot reported a hang involving SCTP, on which it kept flooding dmesg
with the message:
[  246.742374] sctp: sctp_transport_update_pmtu: Reported pmtu 508 too
low, using default minimum of 512

That happened because whenever SCTP hits an ICMP Frag Needed, it tries
to adjust to the new MTU and triggers an immediate retransmission. But
it didn't consider the fact that MTUs smaller than the SCTP minimum MTU
allowed (512) would not cause the PMTU to change, and issued the
retransmission anyway (thus leading to another ICMP Frag Needed, and so
on).

As IPv4 (ip_rt_min_pmtu=556) and IPv6 (IPV6_MIN_MTU=1280) minimum MTU
are higher than that, sctp_transport_update_pmtu() is changed to
re-fetch the PMTU that got set after our request, and with that, detect
if there was an actual change or not.

The fix, thus, skips the immediate retransmission if the received ICMP
resulted in no change, in the hope that SCTP will select another path.

Note: The value being used for the minimum MTU (512,
SCTP_DEFAULT_MINSEGMENT) is not right and instead it should be (576,
SCTP_MIN_PMTU), but such change belongs to another patch.

Changes from v1:
- do not disable PMTU discovery, in the light of commit
06ad3919 ("[SCTP] Don't disable PMTU discovery when mtu is small")
and as suggested by Xin Long.
- changed the way to break the rtx loop by detecting if the icmp
  resulted in a change or not
Changes from v2:
none

See-also: https://lkml.org/lkml/2017/12/22/811Reported-by: Nsyzbot <syzkaller@googlegroups.com>
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, if PMTU discovery is disabled on a given transport, but the
configured value is higher than the actual PMTU, it is likely that we
will get some icmp Frag Needed. The issue is, if PMTU discovery is
disabled, we won't update the information and will issue a
retransmission immediately, which may very well trigger another ICMP,
and another retransmission, leading to a loop.

The fix is to simply not trigger immediate retransmissions if PMTU
discovery is disabled on the given transport.

Changes from v2:
- updated stale comment, noticed by Xin Long
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When loading the module after unloading it, the network interface would
not be enabled and thus wouldn't have a backend counterpart and unable
to be used by the guest.

The guest would face errors like:

  [root@guest ~]# ethtool -i eth0
  Cannot get driver information: No such device

  [root@guest ~]# ifconfig eth0
  eth0: error fetching interface information: Device not found

This patch initializes the state of the netfront device whenever it is
loaded manually, this state would communicate the netback to create its
device and establish the connection between them.
Signed-off-by: NEduardo Otubo <otubo@redhat.com>
Reviewed-by: NBoris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: 2 small bug fixes.

The first one fixes the TC Flower flow parameter passed to firmware.  The
2nd one fixes the VF index range checking for iproute2 SRIOV related commands.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In bnxt_vf_ndo_prep (which is called by bnxt_get_vf_config ndo), there is a
check for "Invalid VF id". Currently, the check is done against max_vfs.
However, the user doesn't always create max_vfs. So, the check should be
against the created number of VFs. The number of bnxt_vf_info structures
that are allocated in bnxt_alloc_vf_resources routine is the "number of
requested VFs". So, if an "invalid VF id" falls between the requested
number of VFs and the max_vfs, the driver will be dereferencing an invalid
pointer.

Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: NVenkat Devvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

flow_type in HWRM_FLOW_ALLOC is not being populated correctly due to
incorrect passing of pointer and size of l3_mask argument of is_wildcard().
Fixed this.

Fixes: db1d36a2 ("bnxt_en: add TC flower offload flow_alloc/free FW cmds")
Signed-off-by: NSunil Challa <sunilkumar.challa@broadcom.com>
Reviewed-by: NSathya Perla <sathya.perla@broadcom.com>
Reviewed-by: NVenkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull cgroup fixes from Tejun Heo:
 "This contains fixes for the following two non-trivial issues:

   - The task iterator got broken while adding thread mode support for
     v4.14. It was less visible because it only triggers when both
     cgroup1 and cgroup2 hierarchies are in use. The recent versions of
     systemd uses cgroup2 for process management even when cgroup1 is
     used for resource control exposing this issue.

   - cpuset CPU hotplug path could deadlock when racing against exits.

  There also are two patches to replace unlimited strcpy() usages with
  strlcpy()"

* 'for-4.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup: fix css_task_iter crash on CSS_TASK_ITER_PROC
  cgroup: Fix deadlock in cpu hotplug path
  cgroup: use strlcpy() instead of strscpy() to avoid spurious warning
  cgroup: avoid copying strings longer than the buffers

Calling acpi_wmi_init() at the subsys_initcall() level causes ordering
issues to appear on some systems and they are difficult to reproduce,
because there is no guaranteed ordering between subsys_initcall()
calls, so they may occur in different orders on different systems.

In particular, commit 86d9f485 (mm/slab: fix kmemcg cache
creation delayed issue) exposed one of these issues where genl_init()
and acpi_wmi_init() are both called at the same initcall level, but
the former must run before the latter so as to avoid a NULL pointer
dereference.

For this reason, move the acpi_wmi_init() invocation to the
initcall_sync level which should still be early enough for things
to work correctly in the WMI land.

Link: https://marc.info/?t=151274596700002&r=1&w=2Reported-by: NJonathan McDowell <noodles@earth.li>
Reported-by: NJoonsoo Kim <iamjoonsoo.kim@lge.com>
Tested-by: NJonathan McDowell <noodles@earth.li>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NDarren Hart (VMware) <dvhart@infradead.org>

Pull parisc fixes from Helge Deller:

 - Many small fixes to show the real physical addresses of devices
   instead of hashed addresses.

 - One important fix to unbreak 32-bit SMP support: We forgot to 16-byte
   align the spinlocks in the assembler code.

 - Qemu support: The host will get a chance to sleep when the parisc
   guest is idle. We use the same mechanism as the power architecture by
   overlaying the "or %r10,%r10,%r10" instruction which is simply a nop
   on real hardware.

* 'parisc-4.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: qemu idle sleep support
  parisc: Fix alignment of pa_tlb_lock in assembly on 32-bit SMP kernel
  parisc: Show unhashed EISA EEPROM address
  parisc: Show unhashed HPA of Dino chip
  parisc: Show initial kernel memory layout unhashed
  parisc: Show unhashed hardware inventory