1. 29 10月, 2005 1 次提交
    • A
      [PATCH] USB: Always do usb-handoff · 478a3bab
      Alan Stern 提交于
      This revised patch (as586b) makes usb-handoff permanently true and no
      longer a kernel boot parameter.  It also removes the piix3_usb quirk code;
      that was nothing more than an early version of the USB handoff code
      (written at a time when Intel's PIIX3 was about the only motherboard with
      USB support).  And it adds identifiers for the three PCI USB controller
      classes to pci_ids.h.
      Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
      Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      478a3bab
  2. 24 10月, 2005 1 次提交
  3. 13 9月, 2005 1 次提交
  4. 08 9月, 2005 1 次提交
    • O
      [PATCH] Add rdinit parameter to pick early userspace init · ffdfc409
      Olof Johansson 提交于
      Since early userspace was added, there's no way to override which init to
      run from it.  Some people tack on an extra cpio archive with a link from
      /init depending on what they want to run, but that's sometimes impractical.
      
      Changing the "init=" to also override the early userspace isn't feasible,
      since it is still used to indicate what init to run from disk when early
      userspace has completed doing whatever it's doing (i.e.  load filesystem
      modules and drivers).
      
      Instead, introduce "rdinit=" and make it override the default "/init" if
      specified.
      Signed-off-by: NOlof Johansson <olof@lixom.net>
      Signed-off-by: NAndrew Morton <akpm@osdl.org>
      Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
      ffdfc409
  5. 04 9月, 2005 1 次提交
  6. 16 8月, 2005 1 次提交
  7. 13 7月, 2005 1 次提交
  8. 08 7月, 2005 1 次提交
  9. 29 6月, 2005 2 次提交
  10. 28 6月, 2005 1 次提交
    • J
      [PATCH] PCI Allow OutOfRange PIRQ table address · 120bb424
      jayalk@intworks.biz 提交于
      I updated this to remove unnecessary variable initialization, make
      check_routing be inline only and not __init, switch to strtoul, and
      formatting fixes as per Randy Dunlap's recommendations.
      
      I updated this to change pirq_table_addr to a long, and to add a warning
      msg if the PIRQ table wasn't found at the specified address, as per thread
      with Matthew Wilcox.
      
      In our hardware situation, the BIOS is unable to store or generate it's PIRQ
      table in the F0000h-100000h standard range. This patch adds a pci kernel
      parameter, pirqaddr to allow the bootloader (or BIOS based loader) to inform
      the kernel where the PIRQ table got stored. A beneficial side-effect is that,
      if one's BIOS uses a static address each time for it's PIRQ table, then
      pirqaddr can be used to avoid the $pirq search through that address block each
      time at boot for normal PIRQ BIOSes.
      Signed-off-by: NJaya Kumar <jayalk@intworks.biz>
      Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      120bb424
  11. 26 6月, 2005 3 次提交
  12. 29 5月, 2005 1 次提交
  13. 17 4月, 2005 1 次提交
    • L
      Linux-2.6.12-rc2 · 1da177e4
      Linus Torvalds 提交于
      Initial git repository build. I'm not bothering with the full history,
      even though we have it. We can create a separate "historical" git
      archive of that later if we want to, and in the meantime it's about
      3.2GB when imported into git - space that would just make the early
      git days unnecessarily complicated, when we don't have a lot of good
      infrastructure for it.
      
      Let it rip!
      1da177e4