Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Add support for Texas Instuments Common Platform Interrupt Controller
(cp_intc) used on DA830/OMAP-L137.
Signed-off-by: NSteve Chen <schen@mvista.com>
Signed-off-by: NMark Greer <mgreer@mvista.com>
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The davinci pre-kernel boot code assumes that all platforms use the
same UART base address for the console.  That assumption is not longer
valid with some newer SoCs so determine the console UART base address
from the machine number passed in from bootloader.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch defines debug macros for low-level debugging for Davinci
based platforms

Tested on :
        - DM644x DaVinci EVM
        - DM646X DaVinciHD EVM
	- DM355 EVM

This patch attempts to solve the low-level debug issue in DM646x. The
UART on DM646x SoC allows only 32-bit access. The existing
debug-macro.S uses the macros from debug-8250.S file. This led to
garbage serial out in the case of DM646x.

The inclusion of debug-8250.S does not allow for run time fix for this
issue.  There are compile time errors due to multiple definitions of
the macros.  Also when building a single image for multiple DaVinci
Platforms, the ifdefs cannot be relied upon.

The solution below does not include the debug-8250.S file and defines
the necessary macros. This solution was arrived at after observing
that word access does not affect the low-level debug messages on
DM644x/DM355.

The other approach to this issue is to use the UART module information
available in the peripheral registers to decide the access
mechanism. But this will have to be done for every access of UART
specifically for DM646x. Also this calls for a modification of the
debug-8250.S file.
Signed-off-by: NChaithrika U S <chaithrika@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch seems to get me much more reliable performance using the
GPIO banked interrupts on dm355 for the dm9000 driver.

Changes include:

- init GPIO handling along with normal GPIO init
- mask the level-sensitive bank IRQ during handling
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Fix two IRQ triggering bugs affecting GPIO IRQs:

 - Make sure enabling with IRQ_TYPE_NONE ("default, unspecified")
   isn't a NOP ... default to both edges, at least one must work.

 - As noted by Kevin Hilman, setting the irq trigger type for a
   banked gpio interrupt shouldn't enable irqs that are disabled.

Since GPIO IRQs haven't been used much yet, it's not clear these
bugs could have affected anything.  The few current users don't
seem to have been obviously suffering from these issues.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This is a build fix, resyncing the DaVinci EVM ASoC board code
with the version in the DaVinci tree.  That resync includes
support for the DM355 EVM, although that board isn't yet in
mainline.

(NOTE:  also includes a bugfix to the platform_add_resources
call, recently sent by Chaithrika U S <chaithrika@ti.com> but
not yet merged into the DaVinci tree.)
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

As per commit 284901a9, use
DMA_BIT_MASK(n)
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Update NAND partitioning for the dm6446 evm, unmasking the hidden
data at the beginning and letting the kernel be updated from Linux.

 - This is boot-compatible with TI's software (U-Boot 1.20 and both
   the 2.6.10 and 2.6.18 kernels), in terms of startup and loading
   kernels from flash.

 - In the same way, it's also boot-compatible with mainline U-Boot,
   which stores U-Boot params in block 0 not block 16.

 - It's not quite compatible with systems that previously used NAND
   partitions to hold (filesystem) data.  The compatibilities are a
   bit different based on which kernel was used previously
     + Users of TI/MV kernels no longer see mtd2 "params"
       (mainline u-boot env is in a different place)
	* Filesystem is now mtd2 ... vs mtd3
     + Users of GIT kernels now see mtd0 and mtd1 partitions
	* Filesystem partition starts 640 KBytes earlier
	* Filesystem is now mtd2 ... vs mtd0
     * Linux now *uses* the flash-resident BBT
	* Removes annoying slowdown/hiccup during boot
	* Potentially ~64KB less space available with TI/MV kernels

If you *used* NAND partitions from Linux, there is no solution that's
fully compatible with all previous kernels in those respects ... ergo
this "best compromise".  It'd be good to back back up the filesystem
data; or, carry your own backwards-compatibility patch for awhile.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Rework DM644x code into SoC specific and board specific parts.
This is also to generalize the structure a bit so it's easier to add
support for new SoCs in the DaVinci family.
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Rename DM6446 EVM board file, no functional changes.  Code is updated
and reworked in following patch.
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Update MUX support to be more general and useful across multiple
SoCs in the DaVinci family.
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Adding IRQ defintions for DaVinci DM355 and default interrupt
priorities for DM355
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Clear any set bits in the 'NEXT' field of the MDCTL register in the
Power and Sleep Controller (PSC) before setting any new bits.
This also allows some minor cleanup by removing some no longer
needed lines of code.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Update the DaVinci GPIO code to work better on non-dm6446 parts,
notably the dm355:

 - Only handle the number of GPIOs the chip actually has.  So
   for example on dm6467, GPIO-42 is the last GPIO, and trying
   to use GPIO-43 now fails cleanly; or GPIO-72 on dm6446.

 - Enable GPIO interrupts on each 16-bit GPIO-irq bank ...
   previously, only the first five were enabled, so GPIO-80
   and above (on dm355) wouldn't trigger IRQs.

 - Use the right IRQ for each GPIO bank.  The wrong values were
   used for dm355 chips, so GPIO IRQs got routed incorrectly.

 - Handle up to four pairs of 16-bit GPIO banks ... previously
   only three were handled, so accessing GPIO-96 and up (e.g. on
   dm355) would oops.

 - Update several comments that were dm6446-specific.

Verified by receiving GPIO-1 (dm9000) and GPIO-5 (msp430) IRQs
on the DM355 EVM.

One thing this doesn't do is handle the way some of the GPIO
numbers on dm6467 are reserved but aren't valid as GPIOs.  Some
bitmap logic could fix that if needed.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Original code for 2.6.10 and 2.6.28 series done by Texas Instruments
and MontaVista, but major updates and rework done by Troy Kisky and
David Brownell.

Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Use clock framework instead of hard-coded CLOCK_TICK_RATE for
determining timer tick frequencies.
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Add arch-specific ioremap() which uses any existing static mappings in
place of doing a new mapping.  From now on, drivers should always use
ioremap() instead of IO_ADDRESS().

In addition, remove the davinci_[read|write]* macros in favor of using
ioremap.
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This is a significant rework of the low-level clock, PLL and Power
Sleep Controller (PSC) implementation for the DaVinci family.  The
primary goal is to have better modeling if the hardware clocks and
features with the aim of DVFS functionality.

Highlights:
- model PLLs and all PLL-derived clocks
- model parent/child relationships of PLLs and clocks
- convert to new clkdev layer
- view clock frequency and refcount via /proc/davinci_clocks

Special thanks to significant contributions and testing by David
Brownell.

Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Pass clocksource pointer to the read() callback for clocksources.  This
allows us to share the callback between multiple instances.

[hugh@veritas.com: fix powerpc build of clocksource pass clocksource mods]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Acked-by: NJohn Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NHugh Dickins <hugh@veritas.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)

Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is a device driver for the NAND flash controller found on the various
DaVinci family chips.  It handles up to four SoC chipselects, and some
flavors of secondary chipselect (e.g.  based on upper bits of the address
bus) as used with some multichip packages.  (Including the 2 GiB chips
used on some TI devel boards.)

The 1-bit ECC hardware is supported (3 bytes ECC per 512 bytes data); but
not yet the newer 4-bit ECC (10 bytes ECC per 512 bytes data), as
available on chips like the DM355 or OMAP-L137 and needed with the more
error-prone MLC NAND chips.

This is a cleaned-up version of code that's been in use for several years
now; sanity checked with the new drivers/mtd/tests.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

OMAP wishes to pass state to the boot loader upon reboot in order to
instruct it whether to wait for USB-based reflashing or not.  There is
already a facility to do this via the reboot() syscall, except we ignore
the string passed to machine_restart().

This patch fixes things to pass this string to arch_reset().  This means
that we keep the reboot mode limited to telling the kernel _how_ to
perform the reboot which should be independent of what we request the
boot loader to do.
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Now that the musb build fixes for DaVinci got merged (RC3?), kick in
the other bits needed to get it finally *working* in mainline:

 - Use clk_enable()/clk_disable() ... the "always enable USB clocks"
   code this originally relied on has since been removed.

 - Initialize the USB device only after the relevant I2C GPIOs are
   available, so the host side can properly enable VBUS.

 - Tweak init sequencing to cope with mainline's relatively late init
   of the I2C system bus for power switches, transceivers, and so on.

Sanity tested on DM6664 EVM for host and peripheral modes; that system
won't boot with CONFIG_PM enabled, so OTG can't yet be tested.  Also
verified on OMAP3.

(Unrelated:  correct the MODULE_PARM_DESC spelling of musb_debug.)
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <me@felipebalbi.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The DaVinci code had an implementation of the OTG transceiver glue
too; make it use the new-standard one.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

From: David Brownell <dbrownell@users.sourceforge.net>
Subject: ARM/mach-davinci/usb.c buildfix

  CC      arch/arm/mach-davinci/usb.o
arch/arm/mach-davinci/usb.c:60: error: 'IRQ_USBINT' undeclared here (not in a function)
make[1]: *** [arch/arm/mach-davinci/usb.o] Error 1
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

arch/arm/mach-at91/at91cap9.c:337: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91rm9200.c:301: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9260.c:351: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9261.c:287: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9263.c:312: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9rl.c:304: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-h720x/h7202-eval.c:38: error: implicit declaration of function 'IRQ_CHAINED_GPIOB'
arch/arm/mach-ks8695/devices.c:46: error: 'KS8695_IRQ_WAN_RX_STATUS' undeclared here (not in a function)
arch/arm/mach-msm/devices.c:28: error: 'INT_UART1' undeclared here (not in a function)
arch/arm/mach-mx2/devices.c:233: error: 'MXC_GPIO_IRQ_START' undeclared here (not in a function)
arch/arm/mach-mx3/devices.c:128: error: 'MXC_GPIO_IRQ_START' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:140: error: 'INT_730_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:165: error: 'INT_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:200: error: 'INT_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap2/board-apollon.c:286: error: implicit declaration of function 'omap_set_gpio_direction'
arch/arm/mach-omap2/mcbsp.c:154: error: 'INT_24XX_MCBSP1_IRQ_RX' undeclared here (not in a function)
arch/arm/mach-omap2/mcbsp.c:181: error: 'INT_24XX_MCBSP1_IRQ_RX' undeclared here (not in a function)
arch/arm/mach-pxa/e350.c:36: error: 'IRQ_BOARD_START' undeclared here (not in a function)
arch/arm/plat-s3c/dev-i2c0.c:32: error: 'IRQ_IIC' undeclared here (not in a function)
...
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Impact: change calling convention of existing clock_event APIs

struct clock_event_timer's cpumask field gets changed to take pointer,
as does the ->broadcast function.

Another single-patch change.  For safety, we BUG_ON() in
clockevents_register_device() if it's not set.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Both of these symbols should be defined by a platform, or neither
should be defined.  Ensure that all platforms conform.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

As Al did for Versatile in 2ad4f86b,
add a typesafe __io implementation for platforms to use.  Convert
platforms to use this new simple typesafe implementation.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

When ISA_DMA_API is unset, we're not implementing the ISA DMA API,
so there's no point in publishing the prototypes via asm/dma.h, nor
including the machine dependent parts of that API.

This allows us to remove a lot of mach/dma.h files which don't contain
any useful code.  Unfortunately though, some platforms put their own
private non-ISA definitions into mach/dma.h, so we leave these behind
and fix the appropriate #include statments.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Move the definition of MAX_DMA_ADDRESS from mach/dma.h to mach/memory.h,
thereby placing it along side its relative, ISA_DMA_THRESHOLD.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Let's provide an overridable default instead of having every machine
class define __virt_to_bus and __bus_to_virt to the same thing.  What
most platforms are using is bus_addr == phys_addr so such is the default.

One exception is ebsa110 which has no DMA what so ever, so the actual
definition is not important except only for proper compilation.  Also
added a comment about the special footbridge bus translation.

Let's also remove comments alluding to set_dma_addr which is not
(and should not) be commonly used.
Signed-off-by: NNicolas Pitre <nico@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

desc_handle_irq() was declared as obsolete since long ago.
Replace it with generic_handle_irq()
Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

id is unsigned, check is redundant.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>