This patch cleans up the code and removes the "(void)level;" warning
suppressor.

Note that we can also use this for PT_PAGE_TABLE_LEVEL to treat every
level uniformly later.
Signed-off-by: NTakuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

There are several cases were we need the control registers for
userspace. Lets also provide those in kvm_run.
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

When we do a stop and store status we need to pass ACTION_STOP_ON_STOP
flag to __sigp_stop().
Signed-off-by: NJens Freimann <jfrei@linux.vnet.ibm.com>
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

In __inject_sigp_stop() do nothing when the CPU is already in stopped
state.
Signed-off-by: NJens Freimann <jfrei@linux.vnet.ibm.com>
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

On reboot the guest sends in smp_send_stop() a sigp stop to all CPUs
except for current CPU.  Then the guest switches to the IPL cpu by
sending a restart to the IPL CPU, followed by a sigp stop to the
current cpu. Since restart is handled by userspace it's possible that
the restart is delivered before the old stop.  This means that the IPL
CPU isn't restarted and we have no running CPUs. So let's make sure
that there is no stop action pending when we do the restart.
Signed-off-by: NJens Freimann <jfrei@linux.vnet.ibm.com>
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

In handle_stop() handle the stop bit before doing the store status as
described for "Stop and Store Status" in the Principles of Operation.
We have to give up the local_int.lock before calling kvm store status
since it calls gmap_fault() which might sleep. Since local_int.lock
only protects local_int.* and not guest memory we can give up the lock.
Signed-off-by: NJens Freimann <jfrei@linux.vnet.ibm.com>
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

commit 7eef87dc (KVM: s390: fix
register setting) added a load of the floating point control register
to the KVM_SET_FPU path. Lets make sure that the fpc is valid.
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

This patch fixes a race introduced by:

  commit 95d4c16c
  KVM: Optimize dirty logging by rmap_write_protect()

During protecting pages for dirty logging, other threads may also try
to protect a page in mmu_sync_children() or kvm_mmu_get_page().

In such a case, because get_dirty_log releases mmu_lock before flushing
TLB's, the following race condition can happen:

  A (get_dirty_log)     B (another thread)

  lock(mmu_lock)
  clear pte.w
  unlock(mmu_lock)
                        lock(mmu_lock)
                        pte.w is already cleared
                        unlock(mmu_lock)
                        skip TLB flush
                        return
  ...
  TLB flush

Though thread B assumes the page has already been protected when it
returns, the remaining TLB entry will break that assumption.

This patch fixes this problem by making get_dirty_log hold the mmu_lock
until it flushes the TLB's.
Signed-off-by: NTakuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

yield_on_hlt was introduced for CPU bandwidth capping. Now it is
redundant with CFS hardlimit.

yield_on_hlt also complicates the scenario in paravirtual environment,
that needs to trap halt. for e.g. paravirtualized ticket spinlocks.
Acked-by: NAnthony Liguori <aliguori@us.ibm.com>
Signed-off-by: NRaghavendra K T <raghavendra.kt@linux.vnet.ibm.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

This allows us to track the original nanosecond and counter values
at each phase of TSC writing by the guest.  This gets us perfect
offset matching for stable TSC systems, and perfect software
computed TSC matching for machines with unstable TSC.
Signed-off-by: NZachary Amsden <zamsden@gmail.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

During a host suspend, TSC may go backwards, which KVM interprets
as an unstable TSC.  Technically, KVM should not be marking the
TSC unstable, which causes the TSC clocksource to go bad, but we
need to be adjusting the TSC offsets in such a case.

Dealing with this issue is a little tricky as the only place we
can reliably do it is before much of the timekeeping infrastructure
is up and running.  On top of this, we are not in a KVM thread
context, so we may not be able to safely access VCPU fields.
Instead, we compute our best known hardware offset at power-up and
stash it to be applied to all VCPUs when they actually start running.
Signed-off-by: NZachary Amsden <zamsden@gmail.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Redefine the API to take a parameter indicating whether an
adjustment is in host or guest cycles.
Signed-off-by: NZachary Amsden <zamsden@gmail.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

The variable last_host_tsc was removed from upstream code.  I am adding
it back for two reasons.  First, it is unnecessary to use guest TSC
computation to conclude information about the host TSC.  The guest may
set the TSC backwards (this case handled by the previous patch), but
the computation of guest TSC (and fetching an MSR) is significanlty more
work and complexity than simply reading the hardware counter.  In addition,
we don't actually need the guest TSC for any part of the computation,
by always recomputing the offset, we can eliminate the need to deal with
the current offset and any scaling factors that may apply.

The second reason is that later on, we are going to be using the host
TSC value to restore TSC offsets after a host S4 suspend, so we need to
be reading the host values, not the guest values here.
Signed-off-by: NZachary Amsden <zamsden@gmail.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

The variable last_guest_tsc was being used as an ad-hoc indicator
that guest TSC has been initialized and recorded correctly.  However,
it may not have been, it could be that guest TSC has been set to some
large value, the back to a small value (by, say, a software reboot).

This defeats the logic and causes KVM to falsely assume that the
guest TSC has gone backwards, marking the host TSC unstable, which
is undesirable behavior.

In addition, rather than try to compute an offset adjustment for the
TSC on unstable platforms, just recompute the whole offset.  This
allows us to get rid of one callsite for adjust_tsc_offset, which
is problematic because the units it takes are in guest units, but
here, the computation was originally being done in host units.

Doing this, and also recording last_guest_tsc when the TSC is written
allow us to remove the tricky logic which depended on last_guest_tsc
being zero to indicate a reset of uninitialized value.

Instead, we now have the guarantee that the guest TSC offset is
always at least something which will get us last_guest_tsc.
Signed-off-by: NZachary Amsden <zamsden@gmail.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Currently, when the TSC is written by the guest, the variable
ns is updated to force the current write to appear to have taken
place at the time of the first write in this sync phase.  This
leaves a cliff at the end of the match window where updates will
fall of the end.  There are two scenarios where this can be a
problem in practe - first, on a system with a large number of
VCPUs, the sync period may last for an extended period of time.

The second way this can happen is if the VM reboots very rapidly
and we catch a VCPU TSC synchronization just around the edge.
We may be unaware of the reboot, and thus the first VCPU might
synchronize with an old set of the timer (at, say 0.97 seconds
ago, when first powered on).  The second VCPU can come in 0.04
seconds later to try to synchronize, but it misses the window
because it is just over the threshold.

Instead, stop doing this artificial setback of the ns variable
and just update it with every write of the TSC.

It may be observed that doing so causes values computed by
compute_guest_tsc to diverge slightly across CPUs - note that
the last_tsc_ns and last_tsc_write variable are used here, and
now they last_tsc_ns will be different for each VCPU, reflecting
the actual time of the update.

However, compute_guest_tsc is used only for guests which already
have TSC stability issues, and further, note that the previous
patch has caused last_tsc_write to be incremented by the difference
in nanoseconds, converted back into guest cycles.  As such, only
boundary rounding errors should be visible, which given the
resolution in nanoseconds, is going to only be a few cycles and
only visible in cross-CPU consistency tests.  The problem can be
fixed by adding a new set of variables to track the start offset
and start write value for the current sync cycle.
Signed-off-by: NZachary Amsden <zamsden@gmail.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

There are a few improvements that can be made to the TSC offset
matching code.  First, we don't need to call the 128-bit multiply
(especially on a constant number), the code works much nicer to
do computation in nanosecond units.

Second, the way everything is setup with software TSC rate scaling,
we currently have per-cpu rates.  Obviously this isn't too desirable
to use in practice, but if for some reason we do change the rate of
all VCPUs at runtime, then reset the TSCs, we will only want to
match offsets for VCPUs running at the same rate.

Finally, for the case where we have an unstable host TSC, but
rate scaling is being done in hardware, we should call the platform
code to compute the TSC offset, so the math is reorganized to recompute
the base instead, then transform the base into an offset using the
existing API.

[avi: fix 64-bit division on i386]
Signed-off-by: NZachary Amsden <zamsden@gmail.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

KVM: Fix 64-bit division in kvm_write_tsc()

Breaks i386 build.
Signed-off-by: NAvi Kivity <avi@redhat.com>

This requires some restructuring; rather than use 'virtual_tsc_khz'
to indicate whether hardware rate scaling is in effect, we consider
each VCPU to always have a virtual TSC rate.  Instead, there is new
logic above the vendor-specific hardware scaling that decides whether
it is even necessary to use and updates all rate variables used by
common code.  This means we can simply query the virtual rate at
any point, which is needed for software rate scaling.

There is also now a threshold added to the TSC rate scaling; minor
differences and variations of measured TSC rate can accidentally
provoke rate scaling to be used when it is not needed.  Instead,
we have a tolerance variable called tsc_tolerance_ppm, which is
the maximum variation from user requested rate at which scaling
will be used.  The default is 250ppm, which is the half the
threshold for NTP adjustment, allowing for some hardware variation.

In the event that hardware rate scaling is not available, we can
kludge a bit by forcing TSC catchup to turn on when a faster than
hardware speed has been requested, but there is nothing available
yet for the reverse case; this requires a trap and emulate software
implementation for RDTSC, which is still forthcoming.

[avi: fix 64-bit division on i386]
Signed-off-by: NZachary Amsden <zamsden@gmail.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Increase recommended max vcpus from 64 to 160 (tested internally
at Red Hat).
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

When kvm guest uses kvmclock, it may hang on vcpu hot-plug.
This is caused by an overflow in pvclock_get_nsec_offset,

    u64 delta = tsc - shadow->tsc_timestamp;

which in turn is caused by an undefined values from percpu
hv_clock that hasn't been initialized yet.
Uninitialized clock on being booted cpu is accessed from
   start_secondary
    -> smp_callin
      ->  smp_store_cpu_info
        -> identify_secondary_cpu
          -> mtrr_ap_init
            -> mtrr_restore
              -> stop_machine_from_inactive_cpu
                -> queue_stop_cpus_work
                  ...
                    -> sched_clock
                      -> kvm_clock_read
which is well before x86_cpuinit.setup_percpu_clockev call in
start_secondary, where percpu clock is initialized.

This patch introduces a hook that allows to setup/initialize
per_cpu clock early and avoid overflow due to reading
  - undefined values
  - old values if cpu was offlined and then onlined again

Another possible early user of this clock source is ftrace that
accesses it to get timestamps for ring buffer entries. So if
mtrr_ap_init is moved from identify_secondary_cpu to past
x86_cpuinit.setup_percpu_clockev in start_secondary, ftrace
may cause the same overflow/hang on cpu hot-plug anyway.

More complete description of the problem:
  https://lkml.org/lkml/2012/2/2/101

Credits to Marcelo Tosatti <mtosatti@redhat.com> for hook idea.
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

The spec says that during initialization "The edge sense circuit is
reset which means that following initialization an interrupt request
(IR) input must make a low-to-high transition to generate an interrupt",
but currently if edge triggered interrupt is in IRR it is delivered
after i8259 initialization.
Signed-off-by: NGleb Natapov <gleb@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

We're currently allocating 16MB of linear memory on demand when creating
a guest. That does work some times, but finding 16MB of linear memory
available in the system at runtime is definitely not a given.

So let's add another command line option similar to the RMA preallocator,
that we can use to keep a pool of page tables around. Now, when a guest
gets created it has a pretty low chance of receiving an OOM.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

RMAs and HPT preallocated spaces should be zeroed, so we don't accidently
leak information from previous VM executions.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Acked-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAvi Kivity <avi@redhat.com>

We have code to allocate big chunks of linear memory on bootup for later use.
This code is currently used for RMA allocation, but can be useful beyond that
extent.

Make it generic so we can reuse it for other stuff later.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Acked-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAvi Kivity <avi@redhat.com>

When enabling the current KVM code on e500mc, I get the following oops:

    Oops: Exception in kernel mode, sig: 4 [#1]
    SMP NR_CPUS=8 P2041 RDB
    Modules linked in:
    NIP: c067df4c LR: c067df44 CTR: 00000000
    REGS: ee055ed0 TRAP: 0700   Not tainted  (3.2.0-10391-g36c5afe)
    MSR: 00029002 <CE,EE,ME>  CR: 24042022  XER: 00000000
    TASK = ee0429b0[1] 'swapper/0' THREAD: ee054000 CPU: 2
    GPR00: c067df44 ee055f80 ee0429b0 00000000 00000058 0000003f ee211600 60c6b864
    GPR08: 7cc903a6 0000002c 00000000 00000001 44042082 2d180088 00000000 00000000
    GPR16: c0000a00 00000014 3fffffff 03fe9000 00000015 7ff3be68 c06e0000 00000000
    GPR24: 00000000 00000000 00001720 c067df1c c06e0000 00000000 ee054000 c06ab51c
    NIP [c067df4c] kvmppc_e500_init+0x30/0xf8
    LR [c067df44] kvmppc_e500_init+0x28/0xf8
    Call Trace:
    [ee055f80] [c067df44] kvmppc_e500_init+0x28/0xf8 (unreliable)
    [ee055fb0] [c0001d30] do_one_initcall+0x50/0x1f0
    [ee055fe0] [c06721dc] kernel_init+0xa4/0x14c
    [ee055ff0] [c000e910] kernel_thread+0x4c/0x68
    Instruction dump:
    9421ffd0 7c0802a6 93410018 9361001c 90010034 93810020 93a10024 93c10028
    93e1002c 4bfffe7d 2c030000 408200a4 <7c1082a6> 90010008 7c1182a6 9001000c
    ---[ end trace b8ef4903fcbf9dd3 ]---

Since it doesn't make sense to run the init function on any non-supported
platform, we can just call our "is this platform supported?" function and
bail out of init() if it's not.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

This moves __gfn_to_memslot() and search_memslots() from kvm_main.c to
kvm_host.h to reduce the code duplication caused by the need for
non-modular code in arch/powerpc/kvm/book3s_hv_rm_mmu.c to call
gfn_to_memslot() in real mode.

Rather than putting gfn_to_memslot() itself in a header, which would
lead to increased code size, this puts __gfn_to_memslot() in a header.
Then, the non-modular uses of gfn_to_memslot() are changed to call
__gfn_to_memslot() instead.  This way there is only one place in the
source code that needs to be changed should the gfn_to_memslot()
implementation need to be modified.

On powerpc, the Book3S HV style of KVM has code that is called from
real mode which needs to call gfn_to_memslot() and thus needs this.
(Module code is allocated in the vmalloc region, which can't be
accessed in real mode.)

With this, we can remove builtin_gfn_to_memslot() from book3s_hv_rm_mmu.c.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Acked-by: NAvi Kivity <avi@redhat.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

If the guest thinks it's an AMD, it will not have prepared the SYSENTER MSRs,
and if the guest executes SYSENTER in compatibility mode, it will fails.

Detect this condition and #UD instead, like the spec says.
Signed-off-by: NAvi Kivity <avi@redhat.com>

If the guest programs an IPI with level=0 (de-assert) and trig_mode=0 (edge),
it is erroneously treated as INIT de-assert and ignored, but to quote the
spec: "For this delivery mode [INIT de-assert], the level flag must be set to
0 and trigger mode flag to 1."
Signed-off-by: NJulian Stecklina <js@alien8.de>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

find_index_from_host_irq returns 0 on error
but callers assume < 0 on error. This should
not matter much: an out of range irq should never happen since
irq handler was registered with this irq #,
and even if it does we get a spurious msix irq in guest
and typically nothing terrible happens.

Still, better to make it consistent.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Also use true instead of 1 for enabling by default.
Signed-off-by: NDavidlohr Bueso <dave@gnu.org>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Signed-off-by: NTakuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Signed-off-by: NTakuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Signed-off-by: NTakuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Currently we treat MOVSX/MOVZX with a byte source as a byte instruction,
and change the destination operand size with a hack.  Change it to be
a word instruction, so the destination receives its natural size, and
change the source to be SrcMem8.
Signed-off-by: NAvi Kivity <avi@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

Useful for MOVSX/MOVZX.
Signed-off-by: NAvi Kivity <avi@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

Instead of keeping separate copies of struct kvm_vcpu_arch_shared (one in
the code, one in the docs) that inevitably fail to be kept in sync
(already sr[] is missing from the doc version), just point to the header
file as the source of documentation on the contents of the magic page.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Acked-by: NAvi Kivity <avi@redhat.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

We need the KVM_REG namespace for generic register settings now, so
let's rename the existing users to something different, enabling
us to reuse the namespace for more visible interfaces.

While at it, also move these private constants to a private header.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

This moves the get/set_one_reg implementation down from powerpc.c into
booke.c, book3s_pr.c and book3s_hv.c.  This avoids #ifdefs in C code,
but more importantly, it fixes a bug on Book3s HV where we were
accessing beyond the end of the kvm_vcpu struct (via the to_book3s()
macro) and corrupting memory, causing random crashes and file corruption.

On Book3s HV we only accept setting the HIOR to zero, since the guest
runs in supervisor mode and its vectors are never offset from zero.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>
[agraf update to apply on top of changed ONE_REG patches]
Signed-off-by: NAvi Kivity <avi@redhat.com>

Until now, we always set HIOR based on the PVR, but this is just wrong.
Instead, we should be setting HIOR explicitly, so user space can decide
what the initial HIOR value is - just like on real hardware.

We keep the old PVR based way around for backwards compatibility, but
once user space uses the SET_ONE_REG based method, we drop the PVR logic.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Right now we transfer a static struct every time we want to get or set
registers. Unfortunately, over time we realize that there are more of
these than we thought of before and the extensibility and flexibility of
transferring a full struct every time is limited.

So this is a new approach to the problem. With these new ioctls, we can
get and set a single register that is identified by an ID. This allows for
very precise and limited transmittal of data. When we later realize that
it's a better idea to shove over multiple registers at once, we can reuse
most of the infrastructure and simply implement a GET_MANY_REGS / SET_MANY_REGS
interface.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Currently the code kzalloc()s new VCPUs instead of using the kmem_cache
which is created when KVM is initialized.

Modify it to allocate VCPUs from that kmem_cache.
Signed-off-by: NSasha Levin <levinsasha928@gmail.com>
Acked-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>