... and no need to perform a linear search for the index.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

The GATT is a write-only set of registers, reading from them in the
manner of i915_gtt_to_phys() is supposed to be undefined. However a
simple solution exists as we allocate linear memory from the stolen
area, we can simply add the block offset to the base register. As a
side-effect we recover all the unused stolen GTT entries and so enlarge
our aperture.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

After a GPU reset, the backlight controller registers may be also reset
to 0. In that case we should restore those to the original values
programmed by the BIOS. Note that we still lack the code to handle the
case where the BIOS failed to program those registers at all...
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

We were reading our 64-bit value in I915_READ64 and returning 32 bits
of it.  The restoration of fence regs at resume then had a zero end
value, and the fence had no effect.

Version 2: Split register access functions into per-size versions

Sharing code between different sizes seemed reasonable when we only
needed a single copy, but as 64-bit access requires its own version,
it makes sense to just split them out for each size.
Reported-by: NPeter Clifton <pcjc2@cam.ac.uk>
Signed-off-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NKeith Packard <keithp@keithp.com>
[ickle: use a macro to create the various read/write routines]
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

This has proven sufficient to recover from a hang of the GPU using the
gem_bad_blit test while at the KMS console then starting X.  When
attempting the same during an X session, the timer doesn't appear to
trigger.
Signed-off-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Signed-off-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

It isn't used for the hangcheck, which does its work right from the
timer trigger, but hangcheck can lead to error state recording, which
is run off of the workqueue.
Signed-off-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

When trying to diagnose mysterious errors on resume, capture the
display register contents as well.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

The pinned buffers are useful for diagnosing errors in setting up state
for the chipset, which may not necessarily be 'active' at the time of
the error, e.g. the cursor buffer object.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Under KMS, restoring the cursor is handled upon modeswitch in order to
avoid enabling an undefined set of registers. At the moment, the cursor
is restored before the aperture and modes are fully setup causing some
invalid access during resume, such as:

  PGTBL_ER: 0x00040000
    Invalid GTT entry during Cursor Fetch

Fix this by only performing cursor register save/restore under UMS where
it is done in the correct sequence.
Reported-by: NArkadiusz Miskiewicz <arekm@maven.pl>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Commit 2549d6c2 removed the vmalloc used for temporary storage of the
relocation lists used during execbuffer. However, our use of vmalloc was
being protected by an integer overflow check which we do want to
preserve!
Reported-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Frame buffer compression is broken on Ironlake due to buggy hardware.
Currently it is disabled through chicken bits, but it still consumes
over 1W more than if we simply never attempt to enable the FBC code
paths.
Signed-off-by: NAlex Shi <alex.shi@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org

Both IBX and CPT have an automatic hotplug detection mode which appears to work reliably enough
that we can dispense with the manual force hotplug trigger stuff. This means that
hotplug detection is as simple as reading the current hotplug register values.

The first time the hotplug detection is activated, the code synchronously waits for a hotplug
sequence in case the hardware hasn't bothered to do a detection cycle since being initialized.
Signed-off-by: NKeith Packard <keithp@keithp.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

We will use this structure in future patches to store CRT specific
information on the encoder.

Split out and tweaked from a patch by Keith Packard.
Signed-off-by: NKeith Packard <keithp@kithp.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Linus Torvalds found that it was rather trivial to trigger a system
freeze:

  In fact, with lockdep, I don't even need to do the sysrq-d thing: it
  shows the bug as it happens. It's the X server taking the same lock
  recursively.

  Here's the problem:

    =============================================
    [ INFO: possible recursive locking detected ]
    2.6.37-rc2-00012-gbdbd01ac #7
    ---------------------------------------------
    Xorg/2816 is trying to acquire lock:
     (&dev->struct_mutex){+.+.+.}, at: [<ffffffff812c626c>] i915_gem_fault+0x50/0x17e

    but task is already holding lock:
     (&dev->struct_mutex){+.+.+.}, at: [<ffffffff812c403b>] i915_mutex_lock_interruptible+0x28/0x4a

    other info that might help us debug this:
    2 locks held by Xorg/2816:
     #0:  (&dev->struct_mutex){+.+.+.}, at: [<ffffffff812c403b>] i915_mutex_lock_interruptible+0x28/0x4a
     #1:  (&mm->mmap_sem){++++++}, at: [<ffffffff81022d4f>] page_fault+0x156/0x37b

This recursion was introduced by rearranging the locking to avoid the
double locking on the fast path (4f27b5d and fbd5a26d) and the
introduction of the prefault to encourage the fast paths (b5e4f2b). In
order to undo the problem, we rearrange the code to perform the access
validation upfront, attempt to prefault and then fight for control of the
mutex.  the best case scenario where the mutex is uncontended the
prefaulting is not wasted.
Reported-and-tested-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Both IBX and CPT have an automatic hotplug detection mode which appears to work reliably enough
that we can dispense with the manual force hotplug trigger stuff. This means that
hotplug detection is as simple as reading the current hotplug register values.

The first time the hotplug detection is activated, the code synchronously waits for a hotplug
sequence in case the hardware hasn't bothered to do a detection cycle since being initialized.
Signed-off-by: NKeith Packard <keithp@keithp.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

We will use this structure in future patches to store CRT specific
information on the encoder.

Split out and tweaked from a patch by Keith Packard.
Signed-off-by: NKeith Packard <keithp@kithp.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

As per advice from Jean Delvare.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

These got lost in the last i2c cleanup.  Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=23222Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

A process suspended waiting for a higher sequence or no sequence to unreserve,
a bo may be beaten to the reservation by a process with a lower sequence.
In that case the first process should give up trying to reserve and
return -EAGAIN. In order for that to happen, we must wake waiting processes
when we change sequence, so that they have a chance to detect the new
sequence.
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

We aren't currently using tiling in userspace on evergreen,
but the info we currently return for the tiling info query
(gb_addr_config) is no adequate for userspace tiling alignment
calculations.  It does not contain the bank info.  Create a custom
tiling info dword with all the necessary info (num channels,
num banks, group size, row size).
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

We were previously dropping alignment requests on the floor
when allocating buffers so we always ended up page aligned.
Certain tiling modes on 6xx+ require larger alignment which
wasn't happening before.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: Jerome Glisse <j.glisse@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This causes the connector to not be added since i2c init fails
for the adapter.  Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=31688

Noticed by Ari Savolainen.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: Ari Savolainen <ari.m.savolainen@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

These are external encoder chips connected via DVO or DP.
The actual external encoder programming is handled by the
kms encoder functions for primary encoder.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Handle all the various asic family specific things for DVO.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The eDP panel must be powered up for aux transactions, so power it
up for detect and mode probe functions, otherwise power it up or
down based on dpms.

v2:
- only mess with eDP panel on DCE4+
- only mess with eDP panel on eDP connectors, not all DP connectors
v3:
- be extra careful to only mess with eDP panels on eDP connectors
v4:
- avoid possible null derefernce if a connector has not been
assigned to the encoder
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

If there was no connector mapped to the encoder, atombios_get_encoder_mode()
returned 0 which is the id for DP.  Return something sane instead based on
the encoder id.  This avoids hitting the DP paths on non-DP encoders.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Seems some newer systems require this explicitly.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Looks like a typo in:
drm/radeon/r600: fix tiling issues in CS checker.
(f30df2fa)
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

enable_vblank implementations should use negative result to indicate error.
radeon_enable_vblank() returns EINVAL in this case.  Change this to -EINVAL.
Signed-off-by: NVasiliy Kulikov <segoon@openwall.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Tiled buffers have the same alignment requirements regardless of
whether the surface is for db, cb, or textures.  Previously, the
calculations where inconsistent for each buffer type.

- Unify the alignment calculations in a common function
- Standardize the alignment units (pixels for pitch/height/depth,
bytes for base)
- properly check the buffer base alignments
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The old code generated an interrupt storm bad enough to completely
take down my system.
Signed-off-by: NAndy Lutomirski <luto@mit.edu>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Avoid confusing userspace by not publishing backlight controls if ACPI
equivalents are available.
Reported-by: NAaron Sowry <aaron@aeneby.se>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Improvements:
 - Fix bug in switch statement
 - Add parts of 0x10022c, 0x10023c
 - Clean up 0x100234
 - Comment out assumption in 0x100228 until verified
Signed-off-by: NRoy Spliet <r.spliet@student.tudelft.nl>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Reported-by: NTomas Miljenovic <tomasmiljenovic@gmail.com>
Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Reported-by: NTomas Miljenovic <tomasmiljenovic@gmail.com>
Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>