Problems with the previous code:
  - HDMI just uses WRPLL1 for everything, so dual head cases might not
    work sometimes.
  - At encoder->mode_set we just write the PLL register without doing
    any kind of check (e.g., check if the PLL is already being used).
  - There is no way to fail and return error codes at
    encoder->mode_set.
  - We write to PORT_CLK_SEL at mode_set and we never disable it.
  - Machines hang due to wrong clock enable/disable sequence.

So here we rewrite the code, making it a little more like the
pre-Haswell PLL mode set code:
  - Check PLL availability at ironlake_crtc_mode_set.
  - Try to use both WRPLLs.
  - Check if PLLs are used before actually trying to use them, and
    properly fail with error messages.
  - Enable/disable PORT_CLK_SEL at the right place.
  - Add some WARNs to check for bugs.

The next improvement will be to try to reuse PLLs if the timings
match, but this is content for another patch and it's already
documented with a TODO comment.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Convert #include "..." to #include <path/...> in drivers/gpu/.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Acked-by: NDave Airlie <airlied@redhat.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: NDave Jones <davej@redhat.com>

Remove redundant DRM UAPI header #inclusions from drivers/gpu/.

Remove redundant #inclusions of core DRM UAPI headers (drm.h, drm_mode.h and
drm_sarea.h).  They are now #included via drmP.h and drm_crtc.h via a preceding
patch.

Without this patch and the patch to make include the UAPI headers from the core
headers, after the UAPI split, the DRM C sources cannot find these UAPI headers
because the DRM code relies on specific -I flags to make #include "..."  work
on headers in include/drm/ - but that does not work after the UAPI split without
adding more -I flags.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Acked-by: NDave Airlie <airlied@redhat.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: NDave Jones <davej@redhat.com>

... even if the actual infoframe is smaller than the maximum possible
size.

If we don't write all the 32 DIP data bytes the InfoFrame ECC may not
be correctly calculated in some cases (e.g., when changing the port),
and this will lead to black screens on HDMI monitors. The ECC value is
generated by the hardware.

I don't see how this should break anything since we're writing 0 and
that should be the correct value, so this patch should be safe.

Notice that on IVB and older we actually have 64 bytes available for
VIDEO_DIP_DATA, but only bytes 0-31 actually store infoframe data: the
others are either read-only ECC values or marked as "reserved". On HSW
we only have 32 bytes, and the ECC value is stored on its own separate
read-only register. See BSpec.

This patch fixes bug #46761, which is marked as a regression
introduced by commit 4e89ee17:
    drm/i915: set the DIP port on ibx_write_infoframe

Before commit 4e89 we were just failing to send AVI infoframes when we
needed to change the port, which can lead to black screens in some
cases. After commit 4e89 we started sending infoframes, but with a
possibly wrong ECC value. After this patch I hope we start sending
correct infoframes.

Version 2:
  - Improve commit message
  - Try to make the code more clear

Cc: stable@vger.kernel.org
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=46761Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This should never happen, but the silent "return" makes me wonder
every time I try to debug InfoFrame bugs, so promote this to BUG() to
make sure people will complain if we ever break this.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Clear Audio Enable bit to trigger unsolicated event to notify Audio
Driver part the HDMI hot plug change. The patch fixed the bug when
remove HDMI cable the bit was not cleared correctly.

In intel_enable_hdmi(), if intel_hdmi->has_audio been true, the "Audio enable bit" will
be set to trigger unsolicated event to notify Alsa driver the change.

intel_hdmi->has_audio will be reset to false from intel_hdmi_detect() after
remove the hdmi cable, here's debug log:

[  187.494153] [drm:output_poll_execute], [CONNECTOR:17:HDMI-A-1] status updated from 1 to 2
[  187.525349] [drm:intel_hdmi_detect], HDMI: has_audio = 0

so when comes back to intel_disable_hdmi(), the "Audio enable bit" will not be cleared. And this
cause the eld infomation and pin presence doesnot update accordingly in alsa driver side.

This patch will also trigger unsolicated event to alsa driver to notify the hot plug event:

[  187.853159] ALSA sound/pci/hda/patch_hdmi.c:772 HDMI hot plug event: Codec=3 Pin=5 Presence_Detect=0 ELD_Valid=1
[  187.853268] ALSA sound/pci/hda/patch_hdmi.c:990 HDMI status: Codec=3 Pin=5 Presence_Detect=0 ELD_Valid=0
Signed-off-by: NWang Xingchao <xingchao.wang@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Clear Audio Enable bit to trigger unsolicated event to notify Audio
Driver part the HDMI hot plug change. The patch fixed the bug when
remove HDMI cable the bit was not cleared correctly.

In intel_hdmi_dpms(), if intel_hdmi->has_audio been true, the "Audio enable bit" will
be set to trigger unsolicated event to notify Alsa driver the change.

intel_hdmi->has_audio will be reset to false from intel_hdmi_detect() after
remove the hdmi cable, here's debug log:

[  187.494153] [drm:output_poll_execute], [CONNECTOR:17:HDMI-A-1] status updated from 1 to 2
[  187.525349] [drm:intel_hdmi_detect], HDMI: has_audio = 0

so when comes back to intel_hdmi_dpms(), the "Audio enable bit" will not be cleared. And this
cause the eld infomation and pin presence doesnot update accordingly in alsa driver side.

This patch will also trigger unsolicated event to alsa driver to notify the hot plug event:

[  187.853159] ALSA sound/pci/hda/patch_hdmi.c:772 HDMI hot plug event: Codec=3 Pin=5 Presence_Detect=0 ELD_Valid=1
[  187.853268] ALSA sound/pci/hda/patch_hdmi.c:990 HDMI status: Codec=3 Pin=5 Presence_Detect=0 ELD_Valid=0
Signed-off-by: NWang Xingchao <xingchao.wang@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Because that's what it is. Unfortunately we can't rip this out because
the fb helper has an incetious relationship with the crtc helper - it
likes to call disable_unused_functions, among other things.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

With the new infrastructure we're doing this when enabling/disabling
the entire display pipe.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Together with the static helper functions drm_crtc_prepare_encoders
and drm_encoder_disable (which will be simplified in the next patch,
but for now are 1:1 copies). Again, no changes beside new names for
these functions.

Also call our new set_mode instead of the crtc helper one now in all
the places we've done so far.

v2: Call the function just intel_set_mode to better differentia it
from intel_crtc_mode_set which really only does the ->mode_set step of
the entire modeset sequence on one crtc. Whereas this function does
the global change.
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

I've picked hdmi as the first encoder to convert because it's rather
simple:
- no cloning possible
- no differences between prepare/commit and dpms off/on switching.

A few changes are required to do so:
- Split up the dpms code into an enable/disable function and wire it
  up with the intel encoder.
- Noop out the existing encoder prepare/commit functions used by the
  crtc helper - our crtc enable/disable code now calls back into the
  encoder enable/disable code at the right spot.
- Create new helper functions to handle dpms changes.
- Add intel_encoder->connectors_active to better track dpms state. Atm
  this is unused, but it will be useful to correctly disable the
  entire display pipe for cloned configurations. Also note that for
  now this is only useful in the dpms code - thanks to the crtc
  helper's dpms confusion across a modeset operation we can't (yet)
  rely on this having a sensible value in all circumstances.
- Rip out the encoder helper dpms callback, if this is still getting
  called somewhere we have a bug. The slight issue with that is that
  the crtc helper abuses dpms off to disable unused functions. Hence
  we also need to implement a default encoder disable function to do
  just that with the new encoder->disable callback.
- Note that we drop the cpt modeset verification in the commit
  callback, too. The right place to do this would be in the crtc's
  enable function, _after_ all the encoders are set up. But because
  not all encoders are converted yet, we can't do that. Hence disable
  this check temporarily as a minor concession to bisectability.

v2: Squash the dpms mode to only the supported values -
connector->dpms is for internal tracking only, we can hence avoid
needless state-changes a bit whithout causing harm.

v3: Apply bikeshed to disable|enable_ddi, suggested by Paulo Zanoni.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Neither the drm core nor any of the drivers really need the raw_edid field
of struct drm_display_info for anything. Instead of being useful, it
creates confusion about who is responsible for freeing the memory it points
to and setting the field to NULL afterwards, leading to memory leaks and
dangling pointers.

Remove the raw_edid field, and fix drivers as necessary.
Reported-by: NRussell King <linux@arm.linux.org.uk>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Acked-by: NInki Dae <inki.dae@samsung.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Instead of having a giant if cascade to figure this out according to
the passed-in register. We could do quite a bit more cleaning up and
all by using the port at more places, but I think this should be part
of a bigger rework to introduce a struct intel_digital_port which
would keep track of all these things. I guess this will be part of
some haswell-DP-induced refactoring.

For now this rips out the big cascade, which is what annoyed me so
much.

v2: Add port variable name back for the func decl (I've tried to trick
myself below the 80 char limit).
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Intel hw only has one MUX for encoders, so outputs are either not
cloneable or all in the same group of cloneable outputs. This neatly
simplifies the code and allows us to ditch some ugly if cascades in
the dp and hdmi init code (well, we need these if cascades for other
stuff still, but that can be taken care of in follow-up patches).

Note that this changes two things:
- dvo can now be cloned with sdvo, but dvo is gen2 whereas sdvo is
  gen3+, so no problem. Note that the old code had a bug and didn't
  allow cloning crt with dvo (but only the other way round).
- sdvo-lvds can now be cloned with sdvo-non-tv. Spec says this won't
  work, but the only reason I've found is that you can't use the
  panel-fitter (used for lvds upscaling) with anything else. But we
  don't use the panel fitter for sdvo-lvds. Imo this part of Bspec is
  a) rather confusing b) mostly as a guideline to implementors (i.e.
  explicitly stating what is already implicit from the spec, without
  always going into the details of why). So I think we can ignore this
  - worst case we'll get a bug report from a user with with sdvo-lvds
  and sdvo-tmds and have to add that special case back in.

Because sdvo lvds is a bit special explain in comments why sdvo LVDS
outputs can be cloned, but native LVDS and eDP can't be cloned - we
use the panel fitter for the later, but not for sdvo.

Note that this also uncoditionally initializes the panel_vdd work used
by eDP. Trying to be clever doesn't buy us anything (but strange bugs)
and this way we can kill the is_edp check.

v2: Incorporate review from Paulo
- Add in a missing space.
- Pimp comment message to address his concerns.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The passed mode must not be modified by the operation, make it const.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This function is supposed to be used at mode set time, so prevent
against future mistakes by adding a WARN().

Based on a patch by Paulo Zanoni, with the check extracted into a
little assert_hdmi_port_disabled helper added to make things self
documenting and move the assert stuff out of line.

[fixed up spelling goof-up while applying.]
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Bspec Vol 3, Part 3, Section 3.8.1.1, bit 30:

"[DevIBX] Writing to this bit only takes effect when port is enabled.
Due to hardware issue it is required that this bit be cleared when port
is disabled. To clear this bit software must temporarily enable this
port on transcoder A."

Unfortunately the public Bspec misses totally out on the same language
for HDMIB. Internal Bspec also mentions that one of the bad
side-effects is that DPx can fail to light up on transcoder A if HDMIx
is disabled but using transcoder B.

I've found this while reviewing Bsepc. We already implement the same
workaround for the DP ports.

Also replace a magic 1 with PIPE_B I've found while looking through the
code.

v2: Implement suggestions from Chris Wilson:
- add pipe variable to cut down on code noise
- write the reg value twice to w/a hw issues (Bspec is unclear on
  which bit actually require the write twice stuff, but better be
  paranoid about it)
- untangle the if logic
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On IVB and older, we basically have two registers: the control and the
data register. We write a few consecutitve times to the control
register, and we need these writes to arrive exactly in the specified
order.

Also, when we're changing the data register, we need to guarantee that
anything written to the control register already arrived (since
changing the control register can change where the data register
points to). Also, we need to make sure all the writes to the data
register happen exactly in the specified order, and we also *can't*
read the data register during this process, since reading and/or
writing it will change the place it points to.

So invoke the "better safe than sorry" rule and just be careful and
put barriers everywhere :)

On HSW we still have a control register that we write many times, but
we have many data registers.
Demanded-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

HSW support is now just like all the other generations: we send AVI
and SPD InfoFrames. There are other DIPs for HSW, but there are other
DIPs for the previous generations too. For each gen, we can see which
DIPs are missing by looking at the 'set_infoframes' function: we
explicitly disable the DIPs we're not using.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The register that controls the HDMI port can be used to control the
sDVO port. Some bits are defined only for sDVO, and SDVO_BORDER_ENABLE
is one of those: HDMI ports that can't be used in sDVO mode don't even
have this bit defined in their specifications.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

At this time, the HDMI port is enabled, and the DIP control register
specification says we need to disable the port *before* disabling the
DIPs. Also, while doing this we risk telling the HW to send the AVI
DIPs once (not every VSync), which really seems to confuse the HW and
trigger bugs where the DIPs are not sent.

This code was here just to set the DIP register to a 'known state'
before using it, but since now the set_infoframes functions already
set the control registers to a known state, this code can go away.

Also, the previous code disables *all* the DIP registers for *each*
HDMI port, so we end disabling each DIP register more than once.

This patch solves a problem I can reproduce on my IVB machine. When I
boot it with just a single HDMI monitor, the AVI InfoFrames are not
sent. With this patch, the InfoFrames are sent. Previously, I wrote a
patch to 'touch the DIP registers after we enable the HDMI port' to
solve this same problem, but that patch doesn't seem to be needed
anymore after this patch.

All this patch does is revert a chunk of the following commit:

    commit 64a8fc01
    Author: Jesse Barnes <jbarnes@virtuousgeek.org>
    Date:   Thu Sep 22 11:16:00 2011 +0530

        drm/i915: fix ILK+ infoframe support

So bugs that can be bisected to that commit may be fixed now.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43256Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The register specification says we need to do this.

V2: Only write the register if the port is enabled.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

From this point on, the 'set_infoframe' functions always set the DIP
registers to a known state, so anything done will always be undone at
the modeset.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This function is called when the pipe is disabled, so it always gets
the 50ms timeout.

This function is called once for each InfoFrame, so we actually get a
100ms timeout. Will be more if we add more InfoFrames.

Also, the spec says we need to "wait for a VSync to ensure completion
of any pending DIP transmissions", not for a VBlank. OTOH, the
register documentation suggests that the DIPs are sent *during* the
VSync, so shouldn't we be waiting until *after* the VSync to ensure
all DIPs are sent?

So this wait_for_vblank seems, besides useless, totally wrong.

If we ever want to change some specific InfoFrame on-the-fly (outside
of the modeset code), the code that changes the InfoFrame will have to
do the waiting itself, and properly.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

So the write_infoframe function can assume the DIP is on.

V2: Be more defensive and add WARN().
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Not once for each InfoFrame. Now we have a function that allows us to
do this.

[danvet: Paulo clarified on irc that a later bugfix patch needs this
cleanup.]
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This solves problems that happen when you alternate between HDMI and
DVI on the same port. I can reproduce these problems using DP->HDMI
and DP->DVI adapters on a DP port.

When you first plug HDMI and then plug DVI, you need to stop sending
DIPs, even if the port is in DVI mode (see the HDMI register spec). If
you don't stop sending DIPs, you'll see a pink vertical line on the
left side of the screen, some modes will give you a black screen, some
modes won't work correctly.

When you first plug DVI and then plug HDMI, you need to properly
enable the DIPs, otherwise the HW won't send them. After spending a
lot of time investigating this, I concluded that if the DIPs are
disabled, we should not write to the DIP register again because when
we do this, we also set the AVI InfoFrame frequency to "once", and
this seems to really confuse our hardware. Since this problem was not
exactly easy to debug, I'm adopting the defensive behavior and not
just avoing the "disable twice" sequence, but also explicitly
selecting the AVI InfoFrame and setting its frequency to a correct
one.

Also, move the "is_dvi" check from intel_set_infoframe to the
set_infoframes functions since now they're going to be the first ones
to deal with the DIP registers.

This patch adds the code to fix the problem, but it depends on the
removal of some code that can't be removed right now and will come
later in the patch series. The patch that we need is:
  - drm/i915: don't write 0 to DIP control at HDMI init

[danvet: Paulo clarified that this additional patch is only required
to make the fix complete, this patch here alone doesn't introduce a
regression but only partially solves the problem of randomly clearing
the dip registers.]

V2: Be even more defensive by selecting AVI and setting its frequency
outside the "is_dvi" check.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need a function that is able to fully 'set' the state of the DIP
registers to a known state.

Currently, we have the write_infoframe function that is called twice:
once for AVI and once for SPD. The problem is that write_infoframe
tries to keep the state of the DIP register as it is, changing only
the minimum necessary bits. The second problem is that
write_infoframe does twice (once for each time it is called) some
work that should be done only once (like waiting for vblank and
setting the port). If we add even more DIPs, it will do even more
repeated work.

This patch only adds the infrastructure keeping the code behavior the
same as before.

v2: add static keywords
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Paulo pointed out that gen4 re-used the SDVO registers for HDMI (the
separate HDMI registers where introduced with the first PCH) and so
g4x_hdmi_connected() never selected the right bit and always returned
disconnected.

Regression in

commit 8ec22b21
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Fri May 11 18:01:34 2012 +0100

    drm/i915/hdmi: Query the live connector status bit for G4x

Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Similar to g4x_dp_detect() we should probe the PORT_HOTPLUG_STATUS as to
whether the connector is active prior to attempting to retrieve the EDID.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Both the control and data registers are completely different now.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

- Changed the coding style of auxiliary infoframe functions to make
  them smaller
- Fixed the column alignment of some function definitions
- Remove definition of "struct drm_crtc" in some places as they're
  used only to retrieve "struct intel_crtc"
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On Haswell, we need to properly train the DDI buffers prior to enabling
HDMI, and enable the required clocks with correct dividers for the desired
frequency.

Also, we cannot simple reuse HDMI routines from previous generations of
GPU, as most of HDMI-specific stuff is being done via the DDI port
programming instead of HDMI-specific registers.

This commit take advantage of the WR PLL clock table which is in a
separate (previous) commit to select the right divisors for each mode.
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Move intel_hdmi data structure and support functions to a shared location,
to allow their usage from intel_ddi module.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Those are driven by DDIs on Haswell architecture, so we need to keep track
of which DDI is being used on each output.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This will throw a BUG() message when an unknown sdvox register is
given to intel_hdmi_init. When this happens, things could going to be pretty
much broken afterwards, so we better detect this as soon as possible.
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Haswell has different DIP control registers and offsets which we need to
use for infoframes, which this patch adds.

Note that this does not adds full DIP frames support, but only the basic
functionality necessary for HDMI to work in early enablement.

v2: replace infoframe handling with a debug message, proper support will
be added via a patch from Paulo Zanoni later.
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: NPaulo Zanoni <przanoni@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

These two functions are actually hw-specific and only valid for gm45
thru gen7. HSW completely changes how this works, so label them
accordingly.

v2: s/gm45/g4x/ like for the previous patch.
Acked-by: NPaulo Zanoni <przanoni@gmail.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Generally we call stuff with i9xx_ when it's valid for gen3+. But
gen3 and early gen4 only support hdmi with sdvo cards, and writing
infoframes works completely different there.

v2: Use g4x instead of gm45 - it applies to the desktop variant, too.

v3: Properly align the paramters of g4x_write_infoframe again, noticed
by Paulo Zanoni.
Acked-by: NPaulo Zanoni <przanoni@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>