Commit ac89a917 ("pty: don't limit the writes to 'pty_space()' inside
'pty_write()'") removed the pty_space() checking, in order to let the
regular tty buffer code limit the buffering itself.

That was all good, but as a subtle side effect it meant that we'd be
doing a tty_wakeup() even in the case where the buffers were all filled
up, and didn't actually make any progress on the write.

Which sounds innocuous, but it interacts very badly with the ppp_async
code, which has an infinite loop in ppp_async_push() that tries to push
out data to the tty.  When we call tty_wakeup(), that loop ends up
thinking that progress was made (see the subtle interactions between
XMIT_WAKEUP and 'tty_stuffed' for details).  End result: one unhappy ppp
user.

Fixed by noticing when tty_insert_flip_string() didn't actually do
anything, and then not doing any more processing (including, very much
not calling tty_wakeup()).
Bisected-and-tested-by: NPeter Volkov <pva@gentoo.org>
Cc: stable@kernel.org (2.6.31)
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is a new pata driver for ARTOP 867X 64bit 4-channel UDMA133 ATA ctrls.
Based on the Atp867 data sheet rev 1.2, Acard, and in part on early ide codes
from Eric Uhrhane <ericu@google.com>.
Signed-off-by: NJohn(Jung-Ik) Lee <jilee@google.com>
Reviewed-by: NGrant Grundler <grundler@google.com>
Reviewed-by: NGwendal Gringo <gwendal@google.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

On a Compaq Presario V3000 laptop (NVIDIA MCP51 chipset), pata_amd selects
PIO0 mode for the PATA DVD-RAM drive instead of MWDMA2 which it supports:

ata4.00: ATAPI: HL-DT-ST DVDRAM GSA-4084N, KQ09, max MWDMA2
ata4: nv_mode_filter: 0x39f&0x7001->0x1, BIOS=0x0 (0x0) ACPI=0x7001 (60:600:0x11)
ata4.00: configured for PIO0

For some reason, the BIOS-set UDMA configuration returns 0 and the ACPI _GTM
reports that UDMA2 and PIO0 are enabled. This causes nv_mode_filter to end up
allowing only PIO0 and UDMA0-2. Since the drive doesn't support UDMA we end up
using PIO0.

Since the controllers should always support PIO4, MWDMA2 and UDMA2 regardless
of what cable type is used, let's make sure we don't filter out these modes
regardless of what wacky settings the BIOS is using.
Signed-off-by: NRobert Hancock <hancockrwd@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

sata_promise's reset code has deviated quite a bit from
the Promise reference driver's, and it has been observed
to fail to recover from errors in some cases.

This patch thus updates the reset code to more closely
match the reference driver:

- soft reset (pdc_reset_port):
  * wait for ATA engine to not be in packet command mode
    (2nd gen only)
  * write reset bit in PDC_CTLSTAT before the first read
    in the loop
  * for 2nd gen SATA follow up with FPDMA reset and clearing
    error status registers
- hard reset (pdc_sata_hardreset):
  * wait for ATA engine to not be in packet command mode
    (2nd gen only)
  * reset ATA engine via the PCI control register
  * Tejun's change to use non-waiting hardreset + follow-up SRST

I'm not changing the hotplug mask bits since they are taken care
of by sata_promise's ->freeze() and ->thaw() operations. And I'm
not writing the PMP port # because that's always zero (for now).

Tested here on various controllers. In particular, one disk
which used to timeout and fail to recover from certain hdparm
and smartmonctl commands now works nicely.
Signed-off-by: NMikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

1st generation Promise SATA chips are prone to generating spurious
hotplug events which can disrupt normal operation. This has been
observed on 20376 and 20378 chips. This patch thus disables hotplug
support on 1st gen chips while leaving it enabled for 2nd gen chips.

The pdc_sata_hotplug_offset() function becomes redundant so it is
removed.

Tested on 1st gen 20376 and 20378 mainboard chips and on a 2nd gen
SATA300 PCI card.
Signed-off-by: NMikael Pettersson <mikpe@it.uu.se>
Tested-by: NKurt Roeckx <kurt@roeckx.be>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Commit 54c38444 makes libata abort qcs
after the port is frozen.  This is necessary to guarantee that TF
registers are accessed after the DMA engine is shutdown after an
error.  However, this triggers WARN_ON_ONCE() check in
ata_qc_complete() spuriously.  Move WARN_ON_ONCE() downwards such that
failing commands while frozen doesn't trigger it.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Commit a5bfc471 dropped explicit
pci_intx() manipulation from ahci because it seemed unnecessary and
ahci doesn't seem to be the right place to be tweaking it if it were.
This was largely okay but there are exceptions.  There was one on an
embedded platform which was fixed via firmware and now bko#14124
reports it on a HP DL320.

  http://bugzilla.kernel.org/show_bug.cgi?id=14124

I still think this isn't something libata drivers should be caring
about (the only ones which are calling pci_intx() explicitly are
libata ones and one other driver) but for now reverting the change
seems to be the right thing to do.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NThomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NMaxime Bizon <mbizon@freebox.fr>
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Acked-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

If we reach the test just below the loop with a `timeout' value of 0,
this does not mean that the timeout caused the loop to end, but rather
the `smi_rd.s.pending', in the last iteration. If timeout caused the
loop to end, then `timeout' is -1, not 0.

Since this can occur only in the last iteration, it is not very likely
to be a problem. By changing the post- to prefix decrement we ensure
that a timeout of 0 does mean it timed out.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NDavid Daney <ddaney@caviumnetworks.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

All cmds issued to BE after the creation of mccq must now use the mcc-q
(and not mbox) to avoid a hw issue that results in mbox poll timeout.
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

use the wrong API when free dma. So when map dma use a flag to
demostrate whether it is 'pci_map_single' or 'pci_map_page'. When free
the dma, check the flags to select the right APIs('pci_unmap_single'
or 'pci_unmap_page').

set the flags type to u16  instead of unsigned long  on David's comments.
Signed-off-by: NJie Yang <jie.yang@atheros.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This sets the number of voltages for the AB3100 regulators so that
they play well with the voltage listing functions and can be used
properly with the MMC regulator integration glue for example.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Instead of hand rolling our own variant.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

KEY_1 and KEY_2 definitions conflicts with include/linux/input.h
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This adds support for the regulators found in the AB3100
Mixed-Signal IC.

It further also defines platform data for the ST-Ericsson
U300 platform and extends the AB3100 MFD driver so that
platform/board data with regulation constraints and an init
function can be passed down all the way from the board to
the regulators.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This adds support for the RTC found inside the AB3100 Mixed Signal chip.
The symbols used for communicating with the chip is found in the
mfd/ab3100-core.c driver that also provides the platform device.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Acked-by: NAlessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

ab3100.h should include linux/workqueue.h for otp to build properly.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

When the sleep script is loaded before the wakeup script, there is a
chance that the system might go to sleep before the wakeup script
loading is completed. This will lead to a system that does not wakeup
and has been observed to cause non-booting boards.

Various options were considered to solve this problem, including
modification of the core twl4030 power code to be smart enough to
reorder the loading of the scripts. But it felt too over-engineered.

Hence this patch just warns the DPS script developer so that they may be
reordered in the board-code itself.
Signed-off-by: NAmit Kucheria <amit.kucheria@verdurent.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The TWL4030/5030 family of multifunction devices allows board-specific
control of the the various regulators, clock and reset lines through
'scripts' that are loaded into its memory. This allows for Dynamic Power
Switching (DPS).

Implement board-independent core support for DPS that is then used by
board-specific code to load custom DPS scripts.
Signed-off-by: NAmit Kucheria <amit.kucheria@verdurent.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This adds the ability to read out OTP (One-Time Programmable)
registers in the AB3100 MFD ASIC. It's a simple sysfs file you
can cat to prompt. The OTP registers of the AB3100 are used to
store various device-unique information such as customer ID,
product flags and the 3GPP standard IMEI (International Mobile
Equipment Indentity) number.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This driver provides basic support for the voltage regulators
integrated into the Freescale MC13783 PMIC. It is currently
only possible to enable/disable outputs, not to actually
set the voltage.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This driver provides the core Freescale MC13783 support. It
registers the client platform_devices and provides access
to the A/D converter.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This will make the worker fire interrupt disable the AB3100 IRQ
without sync which resolves a race since the interrupt obviously
cannot wait for itself to complete while being handled.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This alters the default setting for AB3100_IMRB1 from 0xff to
0xbf. These registers are used for the yet unimplemented ADC
and this new setting will deactivate ADC Trigger 1.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This makes ab3100_set_register_interruptible() propagate the error
code from suboperations properly so it can be handles properly.
(A special case comes from signal interruption.)
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This adds the _interruptible suffix to the AB3100 accessor
functions on par with mutex_lock_interruptible() that's used
for blocking simultaneous calls to the AB3100 acessor functions.
Since these accesses are slow on a 100kHz I2C bus and may line
up waiting for the mutex, we need to handle interruption by
system shutdown or kill signals and may just as well denote that
in the function names.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The WM831x series of PMICs contain RTC functionality. The hardware
provides a 32 bit counter incrementing at 1Hz together with a per
tick interrupt and an alarm value. For simplicity the driver chooses
to define the epoch for the counter as the Unix epoch - if required
platform data can be used in future to customise this.

When powered on from a completely cold state the RTC reports that it
has not been configured - when this happens an error is returned
when attempting to read the RTC in order to avoid use of values we
know to be invalid.

The hardware also provides security features which mean that it can
ignore attempts to set the RTC time in certain circumstances, most
notably if the RTC is written to too often. These errors are detected
by verifying the written RTC value.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NAlessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Right now the pcap core driver passes a reference to its pcap data abusing the
subdrivers platform drvdata, this is not good.

Get the reference directly from the parent device.
Signed-off-by: NAntonio Ospite <ospite@studenti.unina.it>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This is a driver for misc input events for the PCAP2 PMIC, it handles
the Power key and the Headphone button.
Signed-off-by: NDaniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: NIlya Petrov <ilya.muromec@gmail.com>
Signed-off-by: NAntonio Ospite <ospite@studenti.unina.it>
Acked-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Touchscreen driver for the PCAP2 multi function device used in
Motorola EZX smartphones.
Signed-off-by: NDaniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: NStefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: NAntonio Ospite <ospite@studenti.unina.it>
Acked-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Register pcap-regulator earlier so it can be used with cpufreq
Signed-off-by: NDaniel Ribeiro <drwyrm@gmail.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The WM831x series of PMICs provide two constant current sinks
designed to drive strings of serially connected LEDs for applications
such as backlights. This driver adds support for those regulators.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The WM831x series of PMICs include a single DC-DC boost convertor.
This adds basic support for this convertor.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The WM831x series of PMICs provide two optional outputs for
controlling external devices during power sequencing, for example
an external regulator. While in essence these are GPIOs the
hardware presents them as DCDCs with very little control so
provide support via the regulator API in that fashion.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The WM831x series of devices provide three types of LDO:

 - General purpose LDOs supporting voltages from 0.9-3.3V
 - High performance analogue LDOs supporting voltages from 1-3.5V
 - Very low power consumption LDOs intended to support always on
   functionality.

This patch adds support for all three kinds of LDO. Each regulator
is probed as an individual platform device with resources used to
provide the register map location of the regulator. Mixed hardware
and software control of regulators is not current supported.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The WM831x series of devices all have 3 DC-DC buck convertors. This
driver implements software control for these regulators via the
regulator API.  Use with split hardware/software control of individual
regulators is not supported, though regulators not controlled by
software may be controlled via the hardware control interfaces.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This is useful for implementing get_status() in terms of get_mode().
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The WM831x series of PMICs support control of initial power on
through the ON pin on the device with soft control of the pin
at other times. Represent this to userspace as KEY_POWER.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>