Similar to TCP OOO RX queue, it makes sense to use rb trees to store
IP fragments, so that OOO fragments are inserted faster.

Tested:

- a follow-up patch contains a rather comprehensive ip defrag
  self-test (functional)
- ran neper `udp_stream -c -H <host> -F 100 -l 300 -T 20`:
    netstat --statistics
    Ip:
        282078937 total packets received
        0 forwarded
        0 incoming packets discarded
        946760 incoming packets delivered
        18743456 requests sent out
        101 fragments dropped after timeout
        282077129 reassemblies required
        944952 packets reassembled ok
        262734239 packet reassembles failed
   (The numbers/stats above are somewhat better re:
    reassemblies vs a kernel without this patchset. More
    comprehensive performance testing TBD).
Reported-by: NJann Horn <jannh@google.com>
Reported-by: NJuha-Matti Tilli <juha-matti.tilli@iki.fi>
Suggested-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NPeter Oskolkov <posk@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tested: see the next patch is the series.
Suggested-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NPeter Oskolkov <posk@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This behavior is required in IPv6, and there is little need
to tolerate overlapping fragments in IPv4. This change
simplifies the code and eliminates potential DDoS attack vectors.

Tested: ran ip_defrag selftest (not yet available uptream).
Suggested-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NPeter Oskolkov <posk@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Acked-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Function zerocopy_from_iter() unmarks the 'end' in input sgtable while
adding new entries in it. The last entry in sgtable remained unmarked.
This results in KASAN error report on using apis like sg_nents(). Before
returning, the function needs to mark the 'end' in the last entry it
adds.
Signed-off-by: NVakul Garg <vakul.garg@nxp.com>
Acked-by: NDave Watson <davejwatson@fb.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a ICMPV6_PKT_TOOBIG is received from a link local address the pmtu will
be updated on a route with an arbitrary interface index. Subsequent packets
sent back to the same link local address may therefore end up not
considering the updated pmtu.

Current behavior breaks TAHI v6LC4.1.4 Reduce PMTU On-link. Referring to RFC
1981: Section 3: "Note that Path MTU Discovery must be performed even in
cases where a node "thinks" a destination is attached to the same link as
itself. In a situation such as when a neighboring router acts as proxy [ND]
for some destination, the destination can to appear to be directly
connected but is in fact more than one hop away."

Using the interface index from the incoming ICMPV6_PKT_TOOBIG when updating
the pmtu.
Signed-off-by: NGeorg Kohmann <geokohma@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is to support automatic configuration for ptp timer.
If required ptp dts properties are not provided, driver could
try to calculate a set of default configurations to initialize
the ptp timer. This makes the driver work for many boards which
don't have the required ptp dts properties in current kernel.
Also the users could set dts properties by themselves according
to their requirement.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is to add clocks property for fman ptp timer node.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is to add clocks property for fman ptp timer node.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: Updates for net-next.

This series includes the usual firmware spec update.  The driver has
added external phy loopback test and phy setup retry logic that is
needed during hotplug.  In the SRIOV space, the driver has added a
new VF resource allocation mode that requires the VF driver to
reserve resources during IFUP.  IF state changes are now propagated
to firmware so that firmware can release some resources during IFDOWN.

ethtool method to get firmware core dump and hwmon temperature reading
have been added.  DSCP to user priority support has been added to
the driver's DCBNL interface, and the CoS queue logic has been refined
to make sure that the special RDMA Congestion Notification hardware CoS
queue will not be used for networking traffic.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The CNP CoS queue is reserved for internal RDMA Congestion Notification
Packets (CNP) and should not be used for a TC.  Modify the CoS queue
discovery code to skip over the CNP CoS queue and to reduce
bp->max_tc accordingly.  However, if RDMA is disabled in NVRAM, the
the CNP CoS queue can be used for a TC.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Expand the .ieee_setapp() and ieee_delapp() DCBNL methods to support
DSCP.  This allows DSCP values to user priority mappings instead
of using VLAN priorities.  Each DSCP mapping is added or deleted one
entry at a time using the firmware API.  The firmware call can only be
made from a PF.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Export temperature sensor reading via hwmon sysfs.
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use latest firmware API to notify firmware about IF state changes.
Firmware has the option to clean up resources during IF down and
to require the driver to reserve resources again during IF up.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The flags field is almost getting full.  Move firmware capability flags
to a new fw_cap field to better organize these firmware flags.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The BNXT_FLAG_NEW_RM flag is checked a lot in the code to determine if
the new resource manager is in effect.  Define a macro to perform
this check.
Signed-off-by: NMichael Chan <michael.chan@broadocm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to collect live firmware coredump via ethtool.
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set the default hash mode flag in HWRM_VNIC_RSS_CFG to signal to the
firmware that the driver is compliant with the latest spec.  With
that, the firmware can return expanded RSS profile IDs that the driver
checks to setup the proper gso_type for GRO-HW packets.  But instead
of checking for the new profile IDs, we check the IP_TYPE flag
in TPA_START which is more straight forward than checking a list of
profile IDs.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new mode is "minimal-static" to be used when resources are more
limited to support a large number of VFs, for example  The PF driver
will provision guaranteed minimum resources of 0.  Each VF has no
guranteed resources until it tries to reserve resources during device
open.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During hotplug, the driver's open function can be called almost
immediately after power on reset.  The PHY may not be ready and the
firmware may return failure when the driver tries to update PHY
settings.  Add retry logic fired from the driver's timer to retry
the operation for 5 seconds.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add code to detect firmware support for external loopback and the extra
test entry for external loopback.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver gathers statistics using 2 mechanisms.  Some stats are DMA'ed
directly from hardware and others are polled from the driver's timer.
Currently, we only adjust the DMA frequency based on the ethtool
stats-block-usecs setting.  This patch adjusts the driver's timer
frequency as well to make everything consistent.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

New interface has firmware core dump support, new extended port
statistics, and IF state change notifications to the firmware.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter updates for net-next

The following patchset contains Netfilter updates for your net-next tree:

1) Support for transparent proxying for nf_tables, from Mate Eckl.

2) Patchset to add OS passive fingerprint recognition for nf_tables,
   from Fernando Fernandez. This takes common code from xt_osf and
   place it into the new nfnetlink_osf module for codebase sharing.

3) Lightweight tunneling support for nf_tables.

4) meta and lookup are likely going to be used in rulesets, make them
   direct calls. From Florian Westphal.

A bunch of incremental updates:

5) use PTR_ERR_OR_ZERO() from nft_numgen, from YueHaibing.

6) Use kvmalloc_array() to allocate hashtables, from Li RongQing.

7) Explicit dependencies between nfnetlink_cttimeout and conntrack
   timeout extensions, from Harsha Sharma.

8) Simplify NLM_F_CREATE handling in nf_tables.

9) Removed unused variable in the get element command, from
   YueHaibing.

10) Expose bridge hook priorities through uapi, from Mate Eckl.

And a few fixes for previous Netfilter batch for net-next:

11) Use per-netns mutex from flowtable event, from Florian Westphal.

12) Remove explicit dependency on iptables CT target from conntrack
    zones, from Florian.

13) Fix use-after-free in rmmod nf_conntrack path, also from Florian.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Lots of overlapping changes, mostly trivial in nature.

The mlxsw conflict was resolving using the example
resolution at:

https://github.com/jpirko/linux_mlxsw/blob/combined_queue/drivers/net/ethernet/mellanox/mlxsw/core_acl_flex_actions.cSigned-off-by: NDavid S. Miller <davem@davemloft.net>

Pull x86 fix from Thomas Gleixner:
 "A single fix, which addresses boot failures on machines which do not
  report EBDA correctly, which can place the trampoline into reserved
  memory regions. Validating against E820 prevents that"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/boot/compressed/64: Validate trampoline placement against E820

Pull timer fixes from Thomas Gleixner:
 "Two oneliners addressing NOHZ failures:

   - Use a bitmask to check for the pending timer softirq and not the
     bit number. The existing code using the bit number checked for
     the wrong bit, which caused timers to either expire late or stop
     completely.

   - Make the nohz evaluation on interrupt exit more robust. The
     existing code did not re-arm the hardware when interrupting a
     running softirq in task context (ksoftirqd or tail of
     local_bh_enable()), which caused timers to either expire late
     or stop completely"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  nohz: Fix missing tick reprogram when interrupting an inline softirq
  nohz: Fix local_timer_softirq_pending()

Pull perf fixes from Thomas Gleixner:
 "A set of fixes for perf:

  Kernel side:

   - Fix the hardcoded index of extra PCI devices on Broadwell which
     caused a resource conflict and triggered warnings on CPU hotplug.

  Tooling:

   - Update the tools copy of several files, including perf_event.h,
     powerpc's asm/unistd.h (new io_pgetevents syscall), bpf.h and x86's
     memcpy_64.s (used in 'perf bench mem'), silencing the respective
     warnings during the perf tools build.

   - Fix the build on the alpine:edge distro"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/intel/uncore: Fix hardcoded index of Broadwell extra PCI devices
  perf tools: Fix the build on the alpine:edge distro
  tools arch: Update arch/x86/lib/memcpy_64.S copy used in 'perf bench mem memcpy'
  tools headers uapi: Refresh linux/bpf.h copy
  tools headers powerpc: Update asm/unistd.h copy to pick new
  tools headers uapi: Update tools's copy of linux/perf_event.h

Pull irq fix from Thomas Gleixner:
 "A single bugfix for the irq core to prevent silent data corruption and
  malfunction of threaded interrupts under certain conditions"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq: Make force irq threading setup more robust

Pull networking fixes from David Miller:

 1) Handle frames in error situations properly in AF_XDP, from Jakub
    Kicinski.

 2) tcp_mmap test case only tests ipv6 due to a thinko, fix from
    Maninder Singh.

 3) Session refcnt fix in l2tp_ppp, from Guillaume Nault.

 4) Fix regression in netlink bind handling of multicast gruops, from
    Dmitry Safonov.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  netlink: Don't shift on 64 for ngroups
  net/smc: no cursor update send in state SMC_INIT
  l2tp: fix missing refcount drop in pppol2tp_tunnel_ioctl()
  mlxsw: core_acl_flex_actions: Remove redundant mirror resource destruction
  mlxsw: core_acl_flex_actions: Remove redundant counter destruction
  mlxsw: core_acl_flex_actions: Remove redundant resource destruction
  mlxsw: core_acl_flex_actions: Return error for conflicting actions
  selftests/bpf: update test_lwt_seg6local.sh according to iproute2
  drivers: net: lmc: fix case value for target abort error
  selftest/net: fix protocol family to work for IPv4.
  net: xsk: don't return frames via the allocator on error
  tools/bpftool: fix a percpu_array map dump problem

Pull usercopy whitelisting fix from Kees Cook:
 "Bart Massey discovered that the usercopy whitelist for JFS was
  incomplete: the inline inode data may intentionally "overflow" into
  the neighboring "extended area", so the size of the whitelist needed
  to be raised to include the neighboring field"

* tag 'usercopy-fix-v4.18-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  jfs: Fix usercopy whitelist for inline inode data

Pull xfs bugfix from Darrick Wong:
 "One more patch for 4.18 to fix a coding error in the iomap_bmap()
  function introduced in -rc1: fix incorrect shifting"

* tag 'xfs-4.18-fixes-5' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  fs: fix iomap_bmap position calculation

It turns out that commit 721c7fc7 ("block: fail op_is_write()
requests to read-only partitions"), while obviously correct, causes
problems for some older lvm2 installations.

The reason is that the lvm snapshotting will continue to write to the
snapshow COW volume, even after the volume has been marked read-only.
End result: snapshot failure.

This has actually been fixed in newer version of the lvm2 tool, but the
old tools still exist, and the breakage was reported both in the kernel
bugzilla and in the Debian bugzilla:

  https://bugzilla.kernel.org/show_bug.cgi?id=200439
  https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=900442

The lvm2 fix is here

  https://sourceware.org/git/?p=lvm2.git;a=commit;h=a6fdb9d9d70f51c49ad11a87ab4243344e6701a3

but until everybody has updated to recent versions, we'll have to weaken
the "never write to read-only partitions" check.  It now allows the
write to happen, but causes a warning, something like this:

  generic_make_request: Trying to write to read-only block-device dm-3 (partno X)
  Modules linked in: nf_tables xt_cgroup xt_owner kvm_intel iwlmvm kvm irqbypass iwlwifi
  CPU: 1 PID: 77 Comm: kworker/1:1 Not tainted 4.17.9-gentoo #3
  Hardware name: LENOVO 20B6A019RT/20B6A019RT, BIOS GJET91WW (2.41 ) 09/21/2016
  Workqueue: ksnaphd do_metadata
  RIP: 0010:generic_make_request_checks+0x4ac/0x600
  ...
  Call Trace:
   generic_make_request+0x64/0x400
   submit_bio+0x6c/0x140
   dispatch_io+0x287/0x430
   sync_io+0xc3/0x120
   dm_io+0x1f8/0x220
   do_metadata+0x1d/0x30
   process_one_work+0x1b9/0x3e0
   worker_thread+0x2b/0x3c0
   kthread+0x113/0x130
   ret_from_fork+0x35/0x40

Note that this is a "revert" in behavior only.  I'm leaving alone the
actual code cleanups in commit 721c7fc7, but letting the previously
uncaught request go through with a warning instead of stopping it.

Fixes: 721c7fc7 ("block: fail op_is_write() requests to read-only partitions")
Reported-and-tested-by: NWGH <wgh@torlan.ru>
Acked-by: NMike Snitzer <snitzer@redhat.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Ilya Dryomov <idryomov@gmail.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Zdenek Kabelac <zkabelac@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It's legal to have 64 groups for netlink_sock.

As user-supplied nladdr->nl_groups is __u32, it's possible to subscribe
only to first 32 groups.

The check for correctness of .bind() userspace supplied parameter
is done by applying mask made from ngroups shift. Which broke Android
as they have 64 groups and the shift for mask resulted in an overflow.

Fixes: 61f4b237 ("netlink: Don't shift with UB on nlk->ngroups")
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org
Reported-and-Tested-by: NNathan Chancellor <natechancellor@gmail.com>
Signed-off-by: NDmitry Safonov <dima@arista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf 2018-08-05

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) Fix bpftool percpu_array dump by using correct roundup to next
   multiple of 8 for the value size, from Yonghong.

2) Fix in AF_XDP's __xsk_rcv_zc() to not returning frames back to
   allocator since driver will recycle frame anyway in case of an
   error, from Jakub.

3) Fix up BPF test_lwt_seg6local test cases to final iproute2
   syntax, from Mathieu.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Android's header sanitization tool chokes on static inline functions having a
trailing semicolon, leading to an incorrectly parsed header file. While the
tool should obviously be fixed, also fix the header files for the two affected
functions: ethtool_get_flow_spec_ring() and ethtool_get_flow_spec_ring_vf().

Fixes: 8cf6f497 ("ethtool: Add helper routines to pass vf to rx_flow_spec")
Reporetd-by: NBlair Prescott <blair.prescott@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

zhong jiang says:

====================
Use ARRAY_SIZE to replace computing the size

zhong jiang (2):
  net:usb: Use ARRAY_SIZE instead of calculating the array size
  include/net/bond_3ad: Simplify the code by using the ARRAY_SIZE
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We prefer to ARRAY_SIZE rather than the open code to calculate size.
Signed-off-by: Nzhong jiang <zhongjiang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We use ARRAY_SIZE to replace open code sizeof(lan78xx_regs) / sizeof(u32).
It make the code concise.
Signed-off-by: Nzhong jiang <zhongjiang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

0x3ff in tun_hashfn is mask of TUN_NUM_FLOW_ENTRIES, instead
of hardcode, define a macro to setup the relationship with
TUN_NUM_FLOW_ENTRIES
Signed-off-by: NLi RongQing <lirongqing@baidu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>