There is one path with omitted unlock in si470x_fops_release. Fix that.

Cc: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

There is one omitted unlock in em28xx_usb_probe. Fix that.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Discovered the bug that were limiting the output format to just RGB565.
Now, it is possible to output image at Bayer format (the original one,
as generated by Silvercrest sensor, and two others), and also on YUY.

Adds Bayer formats also to the driver.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Webcams have different constraints than other v4l devices. This patch
makes the format ioctls to behave better. It also fixes a bug at open()
handler, that were always reseting resolution to the maximum available
one.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fix the code so that the zl10353 version of the Terratec Cinergy T XS USB
starts working again.  This includes fixing what must have been a typo in the
GPIO definition for the digital side of the board, and setting of the
disable_i2c_gate_ctrl property for the zl10353 config, so that the i2c bus
doesn't get wedged the first time something tries to close the gate.

Also, add a printk() making clear that the mt352 version still isn't
supported.  This issue is still being actively debugged, but in the meantime
at least the dmesg output will show a very clear error...

Thanks to Jelle de Jong for providing sample hardware to test with.

Thanks to Simon Kenyon for testing various patches and providing SSH access to
his environment so I could debug with access to a valid signal source.

Cc: Jelle de Jong <jelledejong@powercraft.nl>
Cc: Simon Kenyon <simon@koala.ie>
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add suppport for the teste RGB565 format (16 bits/pixel).
Currently, webcam support works only at RGB565, at 640x480.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This webcam uses a em2710 chipset, that identifies itself as em2820,
plus a mt9v011 sensor, and a DY-301P lens.

It needs a few different initializations than a normal em28xx device.

Thanks to Hans de Goede <hdegoede@redhat.com> and Douglas Landgraf
<dougsland@redhat.com> for providing the acces for the webcam during
this weekend, I could make a patch for it while returning back from
FISL/Fudcom LATAM 2009.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The original driver for Silvercrest cameras were using some values that
are different from what datasheet says. As result, it was taken very
less snapshots per second than expected.

A test with the datasheet values showed that they work fine and give a
better frame rate. So, let's stick with datasheet values.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Instead of working with a table of precalculated values, fill them with
the proper values. Also, adds format functions that allow changing the
resolution, by cropping the image to the center of the sensor.

While here, move the sensor version check to the probe routine, to
indicate to the caller if the sensor is not supported by this driver.

Also, fixes a stupid bug where we're using &buffer[] instead of
buffer[].
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Adds driver for mt9v011 based on its datasheet, available at:
	http://download.micron.com/pdf/datasheets/imaging/MT9V011.pdf

The driver was tested with a webcam that will be added on a next patch.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

add FIXME comment to indicate that the set_frontend override is a
temporary hack.  This will be done a better way in the next kernel.
Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Use separate RF input spigots for Antennae and Cable.
Reviewed-by: NSteven Toth <stoth@kernellabs.com>
Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Instead of defining a new pif format on an internal header, move it to
the V4L2 API header.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add DVB-T support for Yuan MPC-718 cards with an MT352 or ZL10353 demodulator.

There are apparently some units with a DiBcom demodulator which could be
supported by one of the dib7000 modules - but this is not implemented in the
cx18 driver (yet).

Due to lack of porgramming details for the MT352 and the mt352 module requiring
a "demod_init" function, a "firmware" must be obtained and loaded to get
DVB-T working for Yuan MPC-718 cards with an MT352.
Tested-by: NSteve Firth <firth650@btinternet.com>
Signed-off-by: NAndy Walls <awalls@radix.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAndy Walls <awalls@radix.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The following patch should fix 7 MHz DVB-T with the XC3028 using the
DTV7 firmware from the xc3028-v27.fw firmware image.
Tested-by: NTerry Wu <terrywu2009@gmail.com>
[mchehab@redhat.com: thanks to John Ferlito, we have a real test in Australia]
Signed-off-by: NAndy Walls <awalls@radix.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

If soc_camera_init_user_formats() fails in soc_camera_probe(), we have to call
client's .remove() method to unregister the video device.
Reported-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The supported formats count must be set to 0 after debug output
right before the second pass.
Signed-off-by: NStefan Herbrechtsmeier <hbmeier@hni.uni-paderborn.de>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

If I2C is not enabled, then we shouldn't build ttpci_eeprom.c.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

precalculate_bars() improved vivi performance. However, it assumed that
always before streaming, the driver would call VIDIOC_S_STD. This is not
an API requirement, and the testing apps don't do that.

Due to that, a regression were caused by the patch that added it.

This patch moves the precalculate_bars to the proper place of the code,
calling it at buffer_prepare() callback.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

loaded for a given chip version. This would cause the optimization in
tuning not to be applied and thus a failed expectation, in tuning speed
increment. The patch swaps the tables in use. It also fixes a possible
one in a million condition where state->dev_ver implies an older Cut
(Cut < 2.0, eventhough the driver doesn't attach to any Cut older than
2.0) or even negative (due to a bad I2C bus master driver) for the card
combination.

Thanks to Mauro Carvalho Chehab <mchehab@infradead.org> for pointing
out the issue at large.
Signed-off-by: NManu Abraham <manu@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

drivers/media/dvb/frontends/stv090x.c: In function ‘stv090x_optimize_carloop_short’:
drivers/media/dvb/frontends/stv090x.c:2677: warning: ‘short_crl’ may be used uninitialized in this function
Signed-off-by: NManu Abraham <manu@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

On Fri, 12 Jun 2009, Randy Dunlap wrote:
> From: Randy Dunlap <randy.dunlap@oracle.com>
>
> Move v4l_bound_align_image() outside of an #ifdef CONFIG_I2C block
> so that it is always built.  Fixes a build error:

clamp_align() should be moved as well, since it's only used by
v4l_bound_align_image().  I'm attaching an alternate version that fixes
this.  Labeled the endif too.
Reported-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

In the TRY_FMT handler the function get_scale() is called to find what the
scaler hardware will produce for a requested size.

The problem is that get_scale(struct cx231xx *dev, ..., unsigned int *vscale,
unsigned int *hscale) saves the calculated scale values into both the
pointer arguments and into dev's hscale and vscale fields.  TRY_FMT shouldn't
actually change anything in the device state.

The code to in get_scale() that writes to dev->[hv]scale can just be
deleted.  In all cases when dev's fields should be modified, get_scale()
was called with get_scale(dev, ..., &dev->hscale, &dev->vscale), so dev was
getting updated anyway.

This didn't actually cause a problem because nothing ever actually made use
of the hscale and vscale fields.  I changed cx231xx_resolution_set() to use
those fields rather than re-calculate them with a call to get_scale().

Updating [hv]scale in cx231xx_resolution_set() isn't necessary because
every call of cx231xx_resolution_set() was already preceded by a call to
get_scale() or setting the [hv]scale fields, so they will be always be
up-to-date w.r.t. width and height.

Removing the call to get_scale() from cx231xx_resolution_set() allowed
making get_scale() a static function, which is a good thing for something
with such a short name.  There is already another function with the same
name in the em28xx driver, but that one is static.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The v4l function has a better algorithm for aligning image size.

It appears that the em2800 can only scale by 50% or 100%, i.e. the only
heights supported might be 240 and 480.  In that case the old code would
set any height other than 240 to 480.  Request 240 get 240, but request 239
and then you get 480.  Change it to round to the nearest supported value.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The v4l function has a better algorithm for aligning image size.

Cc: Srinivasa Deevi <srinivasa.deevi@conexant.com>
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The v4l function has a better algorithm for aligning image size.

Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The v4l function has a better algorithm for aligning image size.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The v4l function has a better algorithm for aligning image size.

The existing code was casting pointers to u32 and to unsigned int into
pointers to u16.  This could mess up if someone passed in an image size
greater than 65,535 and on big-endian platforms it won't work at all.

The existing bounding code would shrink an image if it was too big, but
returned ERANGE if it was too small.  The code will not shrink or expand as
necessary.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The v4l function has a better algorithm for aligning image size.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The v4l function has a better algorithm for aligning image size.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The v4l function has a better algorithm for aligning image size.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The v4l function has a better algorithm for aligning image size.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The v4l function has a better algorithm for aligning image size.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The v4l function has a better algorithm for aligning image size.

For instance the old code would change 159x243 into 156x240 to meet the
alignment requirements.  The new function will use 160x243, which is a lot
closer to what was asked for originally.

Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Most hardware has limits on minimum and maximum image dimensions and also
requirements about alignment.  For example, image width must be even or a
multiple of four.  Some hardware has requirements that the total image size
(width * height) be a multiple of some power of two.

v4l_bound_align_image() will enforce min and max width and height, power of
two alignment on width and height, and power of two alignment on total
image size.

It uses an efficient algorithm that will try to find the "closest" image
size that meets the requirements.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add a new s_config core ops call: this is called with the irq and platform
data to be used to initialize the subdev.

Added new v4l2_i2c_new_subdev_cfg and v4l2_i2c_new_subdev_board calls
that allows you to pass these new arguments.

The existing v4l2_i2c_new_subdev functions were modified to also call
s_config.

In the future the existing v4l2_i2c_new_subdev functions will be replaced
by a single v4l2_i2c_new_subdev function similar to v4l2_i2c_new_subdev_cfg
but without the irq and platform_data arguments.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>