There should be no nodes that are not children of the mbus. Move
the nand node under the mbus, and rework the board .dts files
to use an & reference to the nand node.
Signed-off-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

There should be no nodes that are not children of the mbus. Move
the crypto node under the mbus.
Signed-off-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

kirkwood_setup_wins is the last manual caller of mbus in kirkwood, don't
call it for DT boards and rely on the DT having a mbus node with
a proper ranges property to setup these windows.

Move all the mbus ranges properties for all boards into kirkwood.dtsi,
since they are currently all the same.

This makes the DT self consistent, since the physical address of the
NAND and CRYPTO are both referenced internally. The arbitary Linux
constants KIRKWOOD_NAND_MEM_PHYS_BASE and KIRKWOOD_SRAM_PHYS_BASE
no longer have to match the DT values.
Signed-off-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

There appears to be an error in the second address of the second XOR
engine in the Kirkwood SoC device tree, which is specified as 0xd0b00
but should be 0x60b00.

For confirmation of address see table 581 page 658 of:

http://www.marvell.com/embedded-processors/kirkwood/assets/FS_88F6180_9x_6281_OpenSource.pdf

Also see definition of XOR1_HIGH_PHYS_BASE in
arch/arm/mach-kirkwood/include/mach/kirkwood.h
Signed-off-by: NQuentin Armitage <quentin@armitage.org.uk>
Reviewed-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The kirkwood.dtsi cpu@0 node is missing the mandatory reg property.
This causes of_get_cpu_node() to fail to find the node and as a result
the cpufreq driver fails in its probe function.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Now that mbus has been added to the device tree, it's possible to
move the PCIe nodes out of the ocp node, placing it directly
below the mbus. This is a more accurate representation of the hardware.

Moving the PCIe nodes, we now need to introduce an extra cell to
encode the window target ID and attribute. Since this depends on
the PCIe port, we split the ranges translation entries, to
correspond to each MBus window.

In addition, we encode the PCIe memory and I/O apertures in the MBus
node, according to the MBus DT binding specification. The choice made
is 0xe0000000-0xf0000000 for memory space, and 0xf200000-0xf2100000 for
I/O space. These apertures can be changed in each per-board DT file.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This macro is used to define window's target ID and attribute cells
for the MBus ranges entries.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Add a minimal MBus node, just to allow the MBus driver to probe.
Follow-up patches will migrate the rest of the nodes appropriately.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

With recent support for true irqchip and clocksource drivers for Orion
SoCs, now make use of it on DT enabled Kirkwood boards.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This patch adds mv643xx_eth and mvmdio device tree nodes for DT enabled
Kirkwood boards. Phy nodes are also added with reg property set on a
per-board basis.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Although the internal register window size is 1 MiB, the previous
ranges translation for the internal register space had a size of
0x4000000. This was done to allow the crypto and nand node to access
the corresponding 'sram' and 'nand' decoding windows.

In order to describe the hardware more accurately, we declare the
real 1 MiB internal register space in the ranges, and add a translation
entry for the nand node to access the 'nand' window.

This commit will make future improvements on the MBus DT binding easier.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The Kirkwood CPU Freq driver needs a CPU definition in order for the probe
routine to activate it. Add a suitable definition to kirkwood.dtsi

This definition is only correct for single core SoCs. There is a dual core
SoC in the kirkwood family (88F632X) but the rest of the Kirkwood drivers in
the kernel don't currently support it. If they ever do the cpus definition
would need to be duplicated in each of the SoC specific include files.
Signed-off-by: NAdam Baker <linux@baker-net.org.uk>
Tested-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Some kirkwood variants (for instance present in the prestera SoCs) do
not have all the peripherals whose nodes are declared in
kirkwood.dtsi. These missing peripherals are SATA, SDIO, and RTC.

As discussed in [1], to avoid that these missing peripherals get
initialized which could result in system hangs when accessing
undocumented/not present HW registers, their corresponding OF nodes
should not get declared at all for some kirkwood variants.

The corresponding OF nodes of these peripherals thus are moved from
kirkwood.dtsi to the kirkwood-628x.dtsi files so that they still are
initialized for these variants where they are present.

[1]
http://lists.infradead.org/pipermail/linux-arm-kernel/2013-May/167154.htmlSigned-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This commit adds Device Tree details to enable the PCIe interfaces on
Kirkwood. The 6281 has one PCIe interface, the 6282 has two PCIe
interfaces.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

In order to prepare the switch to the standard MMC device tree parser
for mvsdio, adapt all current uses of mvsdio in the dts files to the
standard format.
Signed-off-by: NSimon Baatz <gmbnomis@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The Marvell RTC on Kirkwood makes use of the runit clock. Ensure the
driver clk_prepare_enable() this clock, otherwise there is a danger
the SoC will lockup when accessing RTC registers with the clock
disabled.
Reported-by: NSimon Baatz <gmbnomis@gmail.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NSimon Baatz <gmbnomis@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The kirkwood SoC GPIO cores use the runit clock. Add code to
clk_prepare_enable() runit, otherwise there is a danger of locking up
the SoC by accessing the GPIO registers when runit clock is not
ticking.
Reported-by: NSimon Baatz <gmbnomis@gmail.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NSimon Baatz <gmbnomis@gmail.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

When DT support for kirkwood was first introduced, there was no clock
infrastructure.  As a result, we had to manually pass the
clock-frequency to the driver from the device node.

Unfortunately, on kirkwood, with minimal config or all module configs,
clock-frequency breaks booting because of_serial doesn't consume the
gate_clk when clock-frequency is defined.

The end result on kirkwood is that runit gets gated, and then the boot
fails when the kernel tries to write to the serial port.

Fix the issue by removing the clock-frequency parameter from all
kirkwood dts files.

Booted on dreamplug without earlyprintk and successfully logged in via
ttyS0.
Reported-by: NSimon Baatz <gmbnomis@gmail.com>
Tested-by: NSimon Baatz <gmbnomis@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Now that the SDIO controller has a Device Tree binding, let's use it
in kirkwood.dtsi.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The gpio controller on kirkwood can provide interrupts but is missing
the #interrupt-cells property. This patch just adds it to both gpio
controllers.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Without the clock being held by a driver, it gets turned off at a bad
time causing the SoC to lockup. This is often during reboot.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NStefan Peter <s.peter@mpl.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Select the generic mvebu kirkwood pincltr driver and generic mvebu
gpio driver. This requires minor changes to the DT, and the calls to
configure plat-orion gpio driver are removed.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NMichael Walle <michael@walle.cc>
Tested-by: NSimon Baatz <gmbnomis@gmail.com>
Tested-by: NJamie Lentin <jm@lentin.co.uk>
Tested-by: NJoshua Coombs <josh.coombs@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Now that the EHCI driver has DT support, drop old style configuration
of it and add DT in its place. Since all the boards enable the EHCI,
enable it by default in kirkwood.dtsi. Any new boards which don't have
USB can specifically disable it.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Use DT to describe the two XOR DMA engines on Kirkwood. Remove the
C code initialization.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>

With true DT clock providers available switch Kirkwood clock setup in
DT- enabled boards. While AUXDATA can be removed completely from bus
probing, some devices still don't know about DT. Therefore, some clkdev
aliases are created until these devices also move to DT.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>

Based on work by Michael Walle and Jason Cooper.

Added support for getting the interrupt number and address of SRAM
from DT.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Conflicts:

	arch/arm/mach-kirkwood/board-dt.c

Add support for instantiating this driver from device tree, and add
the necassary DT information to the kirkwood.dtsi file.

This is based on previous work by Michael Walle and Jason Cooper.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NJosh Coombs <josh.coombs@gmail.com>

Add device tree support to the Orion watchdog timer, and enable its
use in the kirkwood devices using device tree.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NSebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Tested-by: NSimon Baatz <gmbnomis@gmail.com>

The MV64XXX I2C driver needs a clock in order to calculate the baud
rate factors. So add an clk to the clk tree. Also add the base DT
properties for kirkwood devices.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>

Conflicts:
	arch/arm/mach-kirkwood/common.c

Populate the devices with auxdata to set the device names which are used by
clkdev to lookup the clocks.
Signed-off-by: NMichael Walle <micheal@walle.cc>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
---
v2: Add interrupts properties, although not used.

Both IRQ and GPIO controllers can now be represented in DT.  The IRQ
controllers are setup first, and then the GPIO controllers. Interrupts
for GPIO lines are placed directly after the main interrupts in the
interrupt space.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NSebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Tested-by: NJosh Coombs <josh.coombs@gmail.com>
Tested-by: NSimon Baatz <gmbnomis@gmail.com>

It has been decided to use marvell, not mrvl, in the compatibility
property. Search & replace.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>

Add default configuration for NAND, to be enabled in your board config. Ensure
clock gating is set appropriately when the NAND is enabled.
Acked-by: NJason Cooper <jason@lakedaemon.net>
Signed-off-by: NJamie Lentin <jm@lentin.co.uk>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Signed-off-by: NJason Cooper <jason@lakedaemon.net>
Acked-by: NArnd Bergmann <arnd@arndb.de>

Define both uarts in kirkwood.dtsi as they are common to all kirkwood
SoCs.  Each board may enable all or none of them, so they are disabled
by default.  uart0 is enabled for the dreamplug.

tclk can vary for each board, so we leave it undefined in the kirkwood
dtsi.  Each board can then set it as appropriate when enabling the uart.
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Also, use inclusive register size for uart0.
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Initially, copied guruplug-setup.c and did s/guruplug/dreamplug/g.
Then, switched to SPI based NOR flash.

After talking to Arnd Bergman, chose an incremental approach to adding
devicetree support.  First, we use the dtb to tell us we are on the
dreamplug, then we gradually port over drivers.

Driver porting will start with the uart (see next patch), and progress
from there.  Possibly, spi/flash/partitions will be next.

When done, board-dt.c will no longer be dreamplug specific, and dt's can
be made for the other kirkwood boards.
Signed-off-by: NJason Cooper <jason@lakedaemon.net>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>