The set_level callback in the controller data, which is used to configure
the slave select line, cannot be supported when migrating the driver to
device tree based discovery. Since all the platforms currently use gpio
as the slave select line, this callback can be removed from the
controller data and replaced with call to gpio_set_value in the driver.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Acked-by: NJaswinder Singh <jaswinder.singh@linaro.org>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

With the spi controller hardware configuration moved into the driver data, there
are no more default hardware configuration data that is passed through platform
data. Accordingly, the s3c64xx_spi{0|1|2}_set_platdata functions are adapted to
these changes.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Acked-by: NJaswinder Singh <jaswinder.singh@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The platform data pointer that is passed to the spi gpio setup functions
is not used. Hence, this parameter is removed from all the spi gpio setup
functions.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Acked-by: NJaswinder Singh <jaswinder.singh@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Platform data is used to specify controller hardware specific information
such as the tx/rx fifo level mask and bit offset of rx fifo level. Such
information is not suitable to be supplied from device tree. Instead,
it can be moved into the driver data and removed from platform data.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Acked-by: NJaswinder Singh <jaswinder.singh@linaro.org>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

While upgrading the kernel on a S3C2412 based board I've noted
that it was impossible to boot the board with a 2.6.32 or upper
kernel. I've tracked down the problem to the EBI virtual memory
mapping that is in conflict with the IO mapping definition in
arch/arm/mach-s3c24xx/s3c2412.c.
Signed-off-by: NJose Miguel Goncalves <jose.goncalves@inov.pt>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

On the error condition clk_get() returns ERR_PTR().
Signed-off-by: NJonghwan Choi <jhbird.choi@samsung.com>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch adds config() that configures DMA transmit option.
This function was originally included in request(). But, Some
DMA client driver requires to change the configuration after
request(). So, This patch picks up it from request().
Signed-off-by: NBoojin Kim <boojin.kim@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The S3C2416 has a separate second interrupt register-set to support
additional irqs. This patch adds the necessary constants and registers
the irq handlers for it.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

A seperate bus_type instance is not required for EXYNOS5. The
existing bus_type instance used with EXYNOS4 is sufficient for
both EXYNOS4 and EXYNOS5. This also solves issue of uninitialized
usage of exynos4_subsys in EXYNOS4 power management code that is
reused for EXYNOS5 also. In addition to that, the existing
exynos4_subsys bus_type is renamed to exynos_subsys to indicate
that it is reused on both EXYNOS4 and EXYNOS5 platforms.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The fout clock of BPLL and MPLL have a selectable source on EXYNOS5250.
The clock options are a fixed divided by 2 clock and the output of the
PLL itself. Add support for these new clock instances.
Signed-off-by: NKisoo Yu <ksoo.yu@samsung.com>
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
[kgene.kim@samsung.com: moved common pll stuff into s5p-clock.c]
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

mach-exynos/dma.c is updated to support both exynos4 and exynos5.
Signed-off-by: NBoojin Kim <boojin.kim@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Add platform device for Exynos DRM core. This device is used
for creating DRM user-space device and allocating memory for
display buffers.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This code removes platform dependency from s3c-hsotg driver.
Signed-off-by: NLukasz Majewski <l.majewski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The sdhci driver is modified to be independent of clk_type member in the sdhci
platform data. Hence, all usage of clk_type in platform code is removed.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
[kgene.kim@samsung.com: re-worked on top of v3.4-rc2]
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

With the addition of platform specific driver data in the sdhci driver
for EXYNOS4 and EXYNOS5, the device name of sdhci controllers on EXYNOS4
and EXYNOS5 are changed accordingly.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
[kgene.kim@samsung.com: re-worked on top of v3.4-rc2]
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The decision to enable or disable the data output to the lcd panel from
the controller need not be based on the value of 'default_win' element
in the platform data. Instead, the data output to the panel is enabled
if any of the windows are active, else data output is disabled.

Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: NFlorian Tobias Schandinat <FlorianSchandinat@gmx.de>

The video interface timing is independent of the window setup data.
The resolution of the window can be smaller than that of the lcd
panel to which the video data is output.

So move the video timing data from the per-window setup data to the
platform specific section in the platform data. This also removes
the restriction that atleast one window should have the same
resolution as that of the panel attached.

Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Acked-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NFlorian Tobias Schandinat <FlorianSchandinat@gmx.de>

This patch removes System MMU device driver from arm/plat-s5p tree
for transition to implement IOMMU driver.
Although controlling System MMU in this removing driver
is similar to the new IOMMU driver in the following patch,
the new one is almost rewrite of this driver and there is no
benefit to moving the driver file from arch/arm/ to drivers/iommu.
Signed-off-by: NKyongHo Cho <pullip.cho@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch add support for EXYNOS5250 SoC has two Cortex-A15 cores.
Since actually, most codes in mach-exynos/ are used commonly for
EXYNOS4 and EXYNOS5 the EXYNOS5/EXYNOS5250 has been implemented
in mach-exynos/.
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Actually, the base address of uart is different between EXYNOS4
and EXYNOS5 and this patch enables to support uart for EXYNOS4
and EXYNOS5 SoCs at runtime.
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch adds clock-exynos5.c for EXYNOS5250 now
and that can be used for other EXYNOS5 SoCs later.
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

In mmc, there are capabilities and use the host_caps.
That capability is expressed with bit[0:31].
But now..already filled the bit[0:31]...
so we need to denote with the other capability field.
(if we want to use the cache, powerclass, etc for eMMC..
 this field is necessary)
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NKyungmin Park <Kyungmin.park@samsung.com>
Acked-by: NChris Ball <cjb@laptop.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Signed-off-by: NBoojin Kim <boojin.kim@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch adds MDMA platform data and enables
MDMA for DMA memcpy operation for EXYNOS SoCs.
Signed-off-by: NBoojin Kim <boojin.kim@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch adds platform_device, clock, map for JPEG
Signed-off-by: NAndrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch supports to control usb otg phy of S3C64XX. Currently, the
driver for usb otg controls usb otg phy but it can be removed by this
patch.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
[Rebased on the newest git/kgene/linux-samsung #for-next]
Signed-off-by: NLukasz Majewski <l.majewski@samsung.com>
Acked-by: Mark Brown<broonie@opensource.wolfsonmicro.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

s3c2443_common_setup_clocks is always called through
s3c2443_common_init_clocks, so there is no need to call it separately.
It was also called twice through this separate call.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The dma controller is similar in S3C2443 and S3C2416 and has also
the same register layout with the same REQSEL-bits in the source
select.

The only small difference is the SIO channel of the S3C2443 for the
non-hsmmc controller which is not present on S3C2416/2450 and
second spi channel which is not present on the S3C2416.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The Simtec extension didn't follow a specific naming scheme for files
and config options until now. This distributed the files throughout
the whole mach-s3c24xx directory.

This patch fixes the naming of files and option names and also creates
a simtec.h header instead of using many one-liners.

As the plat/audio-simtec.h only contains the platform-data struct now,
it can also move to include/sound in a later patch.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch adds s3c_fb_driverdata s3c_fb_data_exynos5 for EXYNOS5
and adds extended timing control setting.

EXYNOS5 FIMD needs extended setting for video timing control.
Additional bits are added to VIDTCON2, VIDWxxADD2, VIDOSDxA and
VIDOSDxB registers in order to set timing value for lager resolution.

Also, address offset of VIDTCONx registers is changed from 0x0
to 0x20000, thus variable type should be changed to int type
to handle the address offset of VIDTCONx registers for EXYNOS5 FIMD.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NFlorian Tobias Schandinat <FlorianSchandinat@gmx.de>

G2D is a 2D graphics accelerator engine present in the s5p family
of Samsung SoCs. It is capable of bitblt and raster operations on
images having dimensions of up to 8000x8000.
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

As the S3C24xx SoCs use the same rtc device a renaming capability like in
the adc driver is necessary.

This patch adds a s3c_rtc_setname function and names the rtc devices for
S3C2443 and S3C2416 accordingly.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Especially the TICNT registers are different from the two rtc
types that currently exists.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Acked-by: NAlessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

regs-rtc.h uses a mixture of tabs and spaces and also (x<<y)
to format bits. So, before adding new stuff clean up the formatting
and also add spaces to the bit definitions (i.e. (x << y) )
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

plat-samsung/clock.h currently keeps all the SoC specific clock
declarations. As we want to get rid of s3c2410.h altogether, move
the s3c2410_baseclk_add there too.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

plat-samsung/clock.h currently keeps all the SoC specific clock
declarations except the ones for S3C2443/S3C2416 which were kept in
s3c2443.h.

This patch moves them out of s3c2443.h to get rid of the header
completely later on.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

clk_msysclk is not needed outside of s3c2443-clock.c.

Removing the extern declaration will prevent conflicts with the
s3c2412 clk_msysclk in the following cleanups.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch adds video clock running at data under-flow.
It means that the pixel clock is continuously provided
to lcd module, even when under-run occurs.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NFlorian Tobias Schandinat <FlorianSchandinat@gmx.de>

This patch adds alpha value width setting according to
transparency value of each window format, using BLENDCON
register. When alpha value is 8 bits, BLENDCON will set
alpha value width as 8 bits.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NFlorian Tobias Schandinat <FlorianSchandinat@gmx.de>

Add pm_caps into platform_data. This is power management, usually
for SDIO device such as SDIO WLAN.
Signed-off-by: NSangwook Lee <sangwook.lee@samsung.com>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>