There really is no point in printing very verbose
error messages when somebody tries to access a
debugfs file before it is ready. Or even worse,
printing verbose messages when memory allocation
fails which *already* prints a huge warning.

Remove all IWL_ERR messages from debugfs.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

This fixes a long-standing bug: iwlwifi always assumes
that the CCK ACK rates are 1 and 2 MBps and the OFDM
ACK rates are 6, 12 and 24 MBps. Fix this problem by
using the basic rates the AP (or in AP case hostapd)
told us to use and add the necessary mandatory rates
to the mix.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Added the option to disable calibration via debugfs.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Since the op_mode may go away, the transport needs to be able to
be told not to update the op_mode at all (even for RF kill).
Provide this API and use it in the proper places.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Since the interrupts have been disabled, we may have missed an RF
kill interrupt. Check the register to be sure the op_mode is in
sync.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The op_mode wants to know about changes in HW RF kill state.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

This can solve a race (very unlikely to happen though).
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

About 70% of the chips with revision RT5390R initialize incorrectly, using
the auxiliary antenna instead of the main one. The net result is that
signal reception is very poor (no AP further than 1M).

This chipset differs from RT5390 and RT5390F by its support of hardware
antenna diversity. Therefore antenna selection should be done
differently, by disabling software features and previously selected
antenna.

This changeset does just that, and makes all RT5390R work properly.

This is based on Ralink's 2012_03_22_RT5572_Linux_STA_v2.6.0.0_DPO
driver.
Signed-off-by: NAnisse Astier <anisse@astier.eu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Legacy rates are not validated while configuring
tx rateset using iw. So below cmd is accepted by nl80211.
sudo iw wlan2 set bitrates legacy-2.4 1 2 3

Validate legacy rates and return
error if any rate in the rateset is not valid.
Signed-off-by: NBala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ieee80211_ave_rssi need to be declare as export for driver to use it.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The original patch defined the correction margin but did not apply it.
Signed-off-by: NShinichi Hotori <hotorinn@gmail.com>
Signed-off-by: NYu Niiro <yu.niiro@gmail.com>
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Extend debugfs entry for dfs_stats with DFS detection events
and shared pool statistics.
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix the following bug: in tkip mode, qos-null ps on/off packets
are dropped due to incorrect packet length so that ath9k softap
can't handle powersave state transition of peer STA correctly.
Signed-off-by: NMichael Liang <mliang@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Convert driver to use private version of dig_t instead of global version.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Convert driver to use the private dig_t instead of a global version.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Convert driver to use the private instead of global version.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Convert rtl8192c to use the dm_digtable struct in the common header file
instead of the global variable. Without this change, every instance of
rtl8192ce and rtl8192cu will be using the same global arrays.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add the dig_t and ps_t structures to the private variables.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move struct definitions for dig_t and ps_t to the common header file.

This move is needed to convert these structures from a "per-driver" to a
"per-interface" basis.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It does not work properly and reduces throughput.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The delay calculation is the same for all chips, however some parts of the
code missed the extra delay factor for half/quarter.
Clean up the code and move the delay calculation to a common place.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For some reason the MAC timing is a bit off when waiting for ACKs, so add
some extra delay to the ACK timeout values. Significantly reduces the
number of retransmissions in my tests.
Also disable the 2.4 GHz ACK timeout workaround in half/quarter mode, it
is not required there.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR9462 uses modified version of 3-Wire hw scheme for btcoex.
MCI itself is not a separate hw scheme but it aids to manage
multiple bt profiles. In ar9462, bt priority traffic is identified
by the number of bt profile types instead of gpio. So that this
patch removes MCI hw scheme.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As of now beacon configuration is being called multiple times
in bss info change notification. This patch avoids multiple
configuration and make it simpler.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds locking of the detector's shared pulse and PRI sequence
pools to enable multi-wiphy operation on SMP systems.
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Without it, I get compile errors due to missing TASK_NORMAL,
TASK_UNINTERRUPTIBLE and schedule.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since the RX path on USB devices is handled in process context we can
use GFP_KERNEL for RX buffer allocation. This should reduce the
likelihood of allocation failures.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Tested-By: NMarc Dietrich <marvin24@gmx.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We're already using BBP for values > 128. Make that explicit and allow
debugfs access.
Signed-off-by: NAnisse Astier <anisse@astier.eu>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch supports Avastar 88W8797 chipset with USB interface.

The corresponding firmware image file is located at:
"mrvl/usb8797_uapsta.bin"
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NFrank Huang <frankh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

According to IEEE 802.11 8.4.2.59, set the "STA channel width" bit to 0
if transmitting STA is using a 20mhz channel.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Blindly setting ht caps on a mesh peer's station entry would result in
MCS rates being used by the rate control algorithm even if no ht had
been configured. Fix this by checking the channel type before assigning
ht capabilites.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To avoid passing supp_rates and basic_rates around all the time, just
derive these when needed in mesh_matches_local() and mesh_peer_init().
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch unifies the previous two paths toward mesh peer creation a
bit. It also fixes a bug where a peer's changing rates or HT mode
wouldn't register on leaving and then returning to the mesh with a sta
entry still present.

Also clean up locking and clear possibly stale ht cap.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The current code unconditionally reads the target
power values for all modes from the EEPROM. However
In 'ar9003_hw_set_power_per_rate_table' the regulatory
caps are applied only on a mode specific subset of the
power values.

The reported TX power level is calculated from the
maximum of the power values. Because some of these
values are uncapped in certain cases, the reported
TX power will be wrong.

On the older chipset, we don't have such problems
because only the mode specific subset of the power
levels are retrieved from the EEPROM on those. Do
the same for the AR9003 chips to fix the issue.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Acked-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>