Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 02 5月, 2012 1 次提交
    • C
      8250.c: less than 2400 baud fix. · f9a9111b
      由 Christian Melki 提交于 
      We noticed that we were loosing data at speed less than 2400 baud.
It turned out our (TI16750 compatible) uart with 64 byte outgoing fifo
was truncated to 16 byte (bit 5 sets fifo len) when modifying the fcr
reg.
The input code still fills the buffer with 64 bytes if I remember
correctly and thus data is lost.
Our fix was to remove whiping of the fcr content and just add the
TRIGGER_1 which we want for latency.
I can't see why this would not work on less than 2400 always, for all
uarts ...
Otherwise one would have to make sure the filling of the fifo re-checks
the current state of available fifo size (urrk).
Signed-off-by: NChristian Melki <christian.melki@ericsson.se>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      f9a9111b
  3. 30 4月, 2012 1 次提交
  5. 19 4月, 2012 7 次提交
    • D
      serial/8250_pci: fix suspend/resume vs init/exit quirks · 5f1a3895
      由 Dan Williams 提交于 
      Commit e86ff4a6 "serial/8250_pci: init-quirk msi support for kt serial
controller" introduced a regression in suspend/resume by causing msi's
to be enabled twice without an intervening disable.

00:16.3 Serial controller: Intel Corporation Patsburg KT Controller (rev 05) (prog-if 02 [16550])
       Subsystem: Intel Corporation Device 7270
       Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 72
       I/O ports at 4080 [size=8]
       Memory at d1c30000 (32-bit, non-prefetchable) [size=4K]
       Capabilities: [c8] Power Management version 3
       Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
       Kernel driver in use: serial

[  365.250523] sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:16.3/msi_irqs'
[  365.250525] Modules linked in: nls_utf8 ipv6 uinput sg iTCO_wdt
  iTCO_vendor_support ioatdma dca i2c_i801 i2c_core wmi sd_mod ahci libahci isci
  libsas libata scsi_transport_sas [last unloaded: scsi_wait_scan]
[  365.250540] Pid: 9030, comm: kworker/u:1 Tainted: G        W    3.3.0-isci-3.0.213+ #1
[  365.250542] Call Trace:
[  365.250545]  [<ffffffff8115e955>] ? sysfs_add_one+0x99/0xad
[  365.250548]  [<ffffffff8102db8b>] warn_slowpath_common+0x85/0x9e
[  365.250551]  [<ffffffff8102dc96>] warn_slowpath_fmt+0x6e/0x70
[  365.250555]  [<ffffffff8115e8fa>] ? sysfs_add_one+0x3e/0xad
[  365.250558]  [<ffffffff8115e8b4>] ? sysfs_pathname+0x3c/0x44
[  365.250561]  [<ffffffff8115e8b4>] ? sysfs_pathname+0x3c/0x44
[  365.250564]  [<ffffffff8115e8b4>] ? sysfs_pathname+0x3c/0x44
[  365.250567]  [<ffffffff8115e8b4>] ? sysfs_pathname+0x3c/0x44
[  365.250570]  [<ffffffff8115e955>] sysfs_add_one+0x99/0xad
[  365.250573]  [<ffffffff8115f031>] create_dir+0x72/0xa5
[  365.250577]  [<ffffffff8115f194>] sysfs_create_dir+0xa2/0xbe
[  365.250581]  [<ffffffff81262463>] kobject_add_internal+0x126/0x1f8
[  365.250585]  [<ffffffff8126255b>] kset_register+0x26/0x3f
[  365.250588]  [<ffffffff8126275a>] kset_create_and_add+0x62/0x7c
[  365.250592]  [<ffffffff81293619>] populate_msi_sysfs+0x34/0x103
[  365.250595]  [<ffffffff81293e1c>] pci_enable_msi_block+0x1b3/0x216
[  365.250599]  [<ffffffff81303f7c>] try_enable_msi+0x13/0x17
[  365.250603]  [<ffffffff81303fb3>] pciserial_resume_ports+0x21/0x42
[  365.250607]  [<ffffffff81304041>] pciserial_resume_one+0x50/0x57
[  365.250610]  [<ffffffff81283e1a>] pci_legacy_resume+0x38/0x47
[  365.250613]  [<ffffffff81283e7d>] pci_pm_restore+0x54/0x87
[  365.250616]  [<ffffffff81283e29>] ? pci_legacy_resume+0x47/0x47
[  365.250619]  [<ffffffff8131e9e8>] dpm_run_callback+0x48/0x7b
[  365.250623]  [<ffffffff8131f39a>] device_resume+0x342/0x394
[  365.250626]  [<ffffffff8131f5b7>] async_resume+0x21/0x49

That patch has since been reverted, but by inspection it seems that
pciserial_suspend_ports() should be invoking .exit() quirks to release
resources acquired during .init().
Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      5f1a3895
    • S
      serial/8250_pci: Clear FIFOs for Intel ME Serial Over Lan device on BI · 0ad372b9
      由 Sudhakar Mamillapalli 提交于 
      When using Serial Over Lan (SOL) over the virtual serial port in a Intel
management engine (ME) device, on device reset the serial FIFOs need to
be cleared to keep the FIFO indexes in-sync between the host and the
engine.

On a reset the serial device assertes BI, so using that as a cue FIFOs
are cleared.  So for this purpose a new handle_break callback has been
added.  One other problem is that the serial registers might temporarily
go to 0 on reset of this device.  So instead of using the IER register
read, if 0 returned use the ier value in uart_8250_port. This is hidden
under a custom serial_in.

Cc: Nhan H Mai <nhan.h.mai@intel.com>
Signed-off-by: NSudhakar Mamillapalli <sudhakar@fb.com>
Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      0ad372b9
    • T
      pch_uart: Fix dma channel unallocated issue · af6d17cd
      由 Tomoya MORINAGA 提交于 
      This driver anticipates pch_uart_verify_port() is not called
during installation.
However, actually pch_uart_verify_port() is called during
installation.
As a result, memory access violation occurs like below.

0. initial value: use_dma=0
1. starup()
    - dma channel is not allocated because use_dma=0
2. pch_uart_verify_port()
    - Set use_dma=1
3. UART processing acts DMA mode because use_dma=1
     - memory access violation occurs!

This patch fixes the issue.

Solution:
Whenever pch_uart_verify_port() is called and then
dma channel is not allocated, the channel should be allocated.
Signed-off-by: NTomoya MORINAGA <tomoya.rohm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      af6d17cd
    • A
      ARM: clps711x: serial driver hungs are a result of call disable_irq within ISR · 7a6fbc9a
      由 Alexander Shiyan 提交于 
      Since 2.6.30-rc1 clps711x serial driver hungs system. This is a result
of call disable_irq from ISR. synchronize_irq waits for end of interrupt
and goes to infinite loop. This patch fix this problem.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      7a6fbc9a
    • D
      tegra, serial8250: add ->handle_break() uart_port op · bf03f65b
      由 Dan Williams 提交于 
      The "KT" serial port has another use case for a "received break" quirk,
so before adding another special case to the 8250 core take this
opportunity to push such quirks out of the core and into a uart_port op.

Stephen says:
"If the callback function is to no longer live in 8250.c itself,
 arch/arm/mach-tegra/devices.c isn't logically a good place to put it,
 and that file will be going away once we get rid of all the board files
 and move solely to device tree."

...so since 8250_pci.c houses all the quirks for pci serial devices this
quirk is similarly housed in of_serial.c.  Once the open firmware
conversion completes the infrastructure details
(include/linux/of_serial.h, and the export) can all be removed to make
this self contained to of_serial.c.

Cc: Nhan H Mai <nhan.h.mai@intel.com>
Cc: Colin Cross <ccross@android.com>
Cc: Olof Johansson <olof@lixom.net>
[stephen: kill CONFIG_SERIAL_TEGRA in favor just using CONFIG_ARCH_TEGRA]
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NSudhakar Mamillapalli <sudhakar@fb.com>
Reported-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Acked-by: NStephen Warren <swarren@wwwdotorg.org>
Tested-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      bf03f65b
    • G
      OMAP2+: UART: Remove cpu checks for populating errata flags · 7c77c8de
      由 Govindraj.R 提交于 
      Currently the errata is populated based on cpu checks this can
be removed and replaced with module version check of uart ip block.
MVR reg is provided within the uart reg map use the same
to populate the errata and thus now errata population and handling
can be managed within the driver itself.

Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Reviewed-by: NJon Hunter <jon-hunter@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      7c77c8de
    • R
      serial: pl011: implement workaround for CTS clear event issue · 4fd0690b
      由 Rajanikanth H.V 提交于 
      Problem Observed:
- interrupt status is set by rising or falling edge on CTS line
- interrupt status is cleared on a .0. to .1. transition of the
  interrupt-clear register bit 1.
- interrupt-clear register is reset by hardware once the interrupt
  status is .0..
  Remark: It seems not possible to read this register back by the
  CPU though, but internally this register exists.
- when simultaneous set and reset event on the interrupt status
  happens, then the set-event has priority and the status remains
  .1.. As a result the interrupt-clear register is not reset to
  .0., and no new .0. to .1. transition can be detected on it when
  writing a .1. to it.
  This implies race condition, the clear must be performed at least
  one UARTCLK the riding edge of CTS RIS interrupt.

Fix:
  Instead of resetting UART as done in commit
  c16d51a3
  "amba pl011: workaround for uart registers lockup" do the
  following:

  write .0. and then  .1. to the interrupt-clear register to make
  sure that this transition is detected. According to the datasheet
  writing a .0. does not have any effect, but actually it allows to
  reset the internal interrupt-clear register.

  Take into account:
  The .0. needs to last at least for one clk_uart clock period
  (~ 38 MHz, 26.08ns)

This way we can do away with the tasklet and keep only a tiny
fix triggered by the variant flag introduced in this patch.
Signed-off-by: NGuillaume Jaunet <guillaume.jaunet@stericsson.com>
Signed-off-by: NChristophe Arnal <christophe.arnal@stericsson.com>
Signed-off-by: NMatthias Locher  <Matthias.Locher@stericsson.com>
Signed-off-by: NRajanikanth H.V <rajanikanth.hv@stericsson.com>
Reviewed-by: NSrinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      4fd0690b
  7. 10 4月, 2012 31 次提交