Fix the failure mode where the display appears split, or shifted about
2/3 of the screen, and the color components are cycled. Turns out we
were missing the crucial BXT_DEFEATURE_DPI_FIFO_CTR bit in the
EOT_DISABLE register.

Per bspec, with the bit set, the "mipi_dpf_vblank_start" signal is
asserted only when the complete frame is transferred in the DPHY line
and also the DPI FIFO is flushed out at the end of each frame.

The problem was mitigated by keeping the panel fitter enabled, but that
only limited the issue to a shift of about 0..10 pixels. With the fix
here, the panel fitter workaround does not seem to be needed at all.

While at it, set BXT_DPHY_DEFEATURE_EN in EOT_DISABLE register which is
also needed per the BXT DSI mode set sequence.

Issue: VIZ-7610
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ramalingam C <ramalingam.c@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464965825-31035-1-git-send-email-jani.nikula@intel.com

On Loading, GuC sets PM interrupts routing (bit 31) and clears ARAT
expired interrupt (bit 9). Host turbo also updates this register
in RPS flows. This patch ensures bit 31 and bit 9 setup by GuC persists.
ARAT timer interrupt is needed in GuC for various features. It also
facilitates halting GuC and hence achieving RC6. PM interrupt routing
will not impact RPS interrupt reception by host as GuC will redirect
them.
This patch fixes igt test pm_rc6_residency that was failing with guc
load/submission enabled. Tested with SKL GuC v6.1 and BXT GuC v5.1 and v8.7.

v2: i915_irq/i915_pm decoupling from intel_guc. (ChrisW)

v3: restructuring the mask update and rebase w.r.t Ville's patch. (ChrisW)

v4: Updating the pm_intr_keep during direct_interrupts_to_guc. (Sagar)

Cc: Chris Harris <chris.harris@intel.com>
Cc: Zhe Wang <zhe1.wang@intel.com>
Cc: Deepak S <deepak.s@intel.com>
Cc: Satyanantha, Rama Gopal M <rama.gopal.m.satyanantha@intel.com>
Cc: Akash Goel <akash.goel@intel.com>
Testcase: igt/pm_rc6_residency
Signed-off-by: NSagar Arun Kamble <sagar.a.kamble@intel.com>
Tested-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464683307-19475-1-git-send-email-sagar.a.kamble@intel.com

Found this while browsing Bspec. Looks like it applies to both skl and
kbl.

v2: Also for bxt (Art).

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Cc: "Pandiyan, Dhinakaran" <dhinakaran.pandiyan@intel.com>
Cc: "Runyan, Arthur J" <arthur.j.runyan@intel.com>
Reviewed-by: Sonika Jindal<sonika.jindal@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463642060-30728-1-git-send-email-daniel.vetter@ffwll.ch

BXT could change the CD2X divider synchronized with a single pipe.
So assuming the DE PLL frequency doesn't need to be changed, we could
change cdclk without shutting off the pipe (when only a single pipe is
enabled). In the meantime let's configure CDCLK_CTL for non-double
buffered CD2X update, although it shouldn't really matter as long as
the selected pipe is disabled when reprogramming the divider.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462995892-32416-13-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

Update CDCLK_FREQ on BDW after changing the cdclk frequency. Not sure
if this is a late addition to the spec, or if I simply overlooked this
step when writing the original code.

This is what Bspec has to say about CDCLK_FREQ:
"Program this field to the CD clock frequency minus one. This is used to
 generate a divided down clock for miscellaneous timers in display."

And the "Broadwell Sequences for Changing CD Clock Frequency" section
clarifies this further:
"For CD clock 337.5 MHz, program 337 decimal.
 For CD clock 450 MHz, program 449 decimal.
 For CD clock 540 MHz, program 539 decimal.
 For CD clock 675 MHz, program 674 decimal."

Cc: stable@vger.kernel.org
Cc: Mika Kahola <mika.kahola@intel.com>
Fixes: b432e5cf ("drm/i915: BDW clock change support")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461689194-6079-2-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NMika Kahola <mika.kahola@intel.com>
(cherry picked from commit 7f1052a8)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

While browsing BSpec I bumped into a note saying we need to tune these
values based on actual measurements done after initial enabling. I've
checked that it indeed improves things on BXT. I haven't checked this on
CHV, but here it is if someone wants to give it a go.

v2:
- Add note about the discrepancy wrt. to the spec in the formula
  calculating the credit encodings. (Mika, Ville)
- Move the WA comment to the new function. (Ville)
v3:
- Keep the comment about the SQC WA in the caller. (Ville)

CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
CC: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462280061-1457-4-git-send-email-imre.deak@intel.com

No need for hard-coding the register value, the corresponding fields are
defined properly in BSpec.

No functional change.

v2:
- Rebased on BXT L3 SQC tuning patch merged meanwhile.

CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1462280061-1457-3-git-send-email-imre.deak@intel.com

Update CDCLK_FREQ on BDW after changing the cdclk frequency. Not sure
if this is a late addition to the spec, or if I simply overlooked this
step when writing the original code.

This is what Bspec has to say about CDCLK_FREQ:
"Program this field to the CD clock frequency minus one. This is used to
 generate a divided down clock for miscellaneous timers in display."

And the "Broadwell Sequences for Changing CD Clock Frequency" section
clarifies this further:
"For CD clock 337.5 MHz, program 337 decimal.
 For CD clock 450 MHz, program 449 decimal.
 For CD clock 540 MHz, program 539 decimal.
 For CD clock 675 MHz, program 674 decimal."

Cc: stable@vger.kernel.org
Cc: Mika Kahola <mika.kahola@intel.com>
Fixes: b432e5cf ("drm/i915: BDW clock change support")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461689194-6079-2-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NMika Kahola <mika.kahola@intel.com>

I just noticed that VLV/CHV have a RAWCLK_FREQ register just like PCH
platforms. It lives in the display power well, so we should update it
when enabling the power well.

Interestingly the BIOS seems to leave it at the reset value (125) which
doesn't match the rawclk frequency on VLV/CHV (200 MHz). As always with
these register, the spec is extremely vague what the register does. All
it says is: "This is used to generate a divided down clock for
miscellaneous timers in display." Based on a quick test, at least AUX
and PWM appear to be unaffected by this.

But since the register is there, let's configure it in accordance with
the spec.

Note that we have to move intel_update_rawclk() to occur before we
touch the power wells, so that the dev_priv->rawclk_freq is already
populated when the disp2 enable hook gets called for the first time.
I think this should be safe to do on other platforms as well.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461768202-17544-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Somehow my SNB GT1 (Dell XPS 8300) gets very unhappy around
GPU hangs if the RPS EI/thresholds aren't suitably aligned.
It seems like scheduling/timer interupts stop working somehow
and things get stuck eg. in usleep_range().

I bisected the problem down to
commit 8a586437 ("drm/i915/skl: Restructured the gen6_set_rps_thresholds function")
I observed that before all the values were at least multiples of 25,
but afterwards they are not. And rounding things up to the next multiple
of 25 does seem to help, so lets' do that. I also tried roundup(..., 5)
but that wasn't sufficient. Also I have no idea if we might need this sort of
thing on gen9+ as well.

These are the original EI/thresholds:
 LOW_POWER
  GEN6_RP_UP_EI          12500
  GEN6_RP_UP_THRESHOLD   11800
  GEN6_RP_DOWN_EI        25000
  GEN6_RP_DOWN_THRESHOLD 21250
 BETWEEN
  GEN6_RP_UP_EI          10250
  GEN6_RP_UP_THRESHOLD    9225
  GEN6_RP_DOWN_EI        25000
  GEN6_RP_DOWN_THRESHOLD 18750
 HIGH_POWER
  GEN6_RP_UP_EI           8000
  GEN6_RP_UP_THRESHOLD    6800
  GEN6_RP_DOWN_EI        25000
  GEN6_RP_DOWN_THRESHOLD 15000

These are after 8a586437:
 LOW_POWER
  GEN6_RP_UP_EI          12500
  GEN6_RP_UP_THRESHOLD   11875
  GEN6_RP_DOWN_EI        25000
  GEN6_RP_DOWN_THRESHOLD 21250
 BETWEEN
  GEN6_RP_UP_EI          10156
  GEN6_RP_UP_THRESHOLD    9140
  GEN6_RP_DOWN_EI        25000
  GEN6_RP_DOWN_THRESHOLD 18750
 HIGH_POWER
  GEN6_RP_UP_EI           7812
  GEN6_RP_UP_THRESHOLD    6640
  GEN6_RP_DOWN_EI        25000
  GEN6_RP_DOWN_THRESHOLD 15000

And these are what we have after this patch:
 LOW_POWER
  GEN6_RP_UP_EI          12500
  GEN6_RP_UP_THRESHOLD   11875
  GEN6_RP_DOWN_EI        25000
  GEN6_RP_DOWN_THRESHOLD 21250
 BETWEEN
  GEN6_RP_UP_EI          10175
  GEN6_RP_UP_THRESHOLD    9150
  GEN6_RP_DOWN_EI        25000
  GEN6_RP_DOWN_THRESHOLD 18750
 HIGH_POWER
  GEN6_RP_UP_EI           7825
  GEN6_RP_UP_THRESHOLD    6650
  GEN6_RP_DOWN_EI        25000
  GEN6_RP_DOWN_THRESHOLD 15000

Cc: stable@vger.kernel.org
Cc: Akash Goel <akash.goel@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Testcase: igt/kms_pipe_crc_basic/hang-read-crc-pipe-B
Fixes: 8a586437 ("drm/i915/skl: Restructured the gen6_set_rps_thresholds function")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461159836-9108-1-git-send-email-ville.syrjala@linux.intel.comAcked-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NPatrik Jakobsson <patrik.jakobsson@linux.intel.com>
(cherry picked from commit 8a292d01)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

This patch applies a performance enhancement workaround
based on analysis of DX and OCL S-Curve workloads. We
increase the General Priority Credits for L3SQ from the
hardware default of 56 to the max value 62, and decrease
the High Priority credits from 8 to 2.

v2: Only apply to B0 onwards

v3: Move w/a to per engine init, ie bxt_init_workarounds
Signed-off-by: NTim Gore <tim.gore@intel.com>
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461314761-36854-1-git-send-email-tim.gore@intel.comReviewed-by: NMichel Thierry <michel.thierry@intel.com>

Added a new GT_PM_INTERVAL_TO_US macro to perform the platform
specific conversion of PM time interval values to microseconds unit.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NAkash Goel <akash.goel@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1461350146-23454-1-git-send-email-akash.goel@intel.comSigned-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Somehow my SNB GT1 (Dell XPS 8300) gets very unhappy around
GPU hangs if the RPS EI/thresholds aren't suitably aligned.
It seems like scheduling/timer interupts stop working somehow
and things get stuck eg. in usleep_range().

I bisected the problem down to
commit 8a586437 ("drm/i915/skl: Restructured the gen6_set_rps_thresholds function")
I observed that before all the values were at least multiples of 25,
but afterwards they are not. And rounding things up to the next multiple
of 25 does seem to help, so lets' do that. I also tried roundup(..., 5)
but that wasn't sufficient. Also I have no idea if we might need this sort of
thing on gen9+ as well.

These are the original EI/thresholds:
 LOW_POWER
  GEN6_RP_UP_EI          12500
  GEN6_RP_UP_THRESHOLD   11800
  GEN6_RP_DOWN_EI        25000
  GEN6_RP_DOWN_THRESHOLD 21250
 BETWEEN
  GEN6_RP_UP_EI          10250
  GEN6_RP_UP_THRESHOLD    9225
  GEN6_RP_DOWN_EI        25000
  GEN6_RP_DOWN_THRESHOLD 18750
 HIGH_POWER
  GEN6_RP_UP_EI           8000
  GEN6_RP_UP_THRESHOLD    6800
  GEN6_RP_DOWN_EI        25000
  GEN6_RP_DOWN_THRESHOLD 15000

These are after 8a586437:
 LOW_POWER
  GEN6_RP_UP_EI          12500
  GEN6_RP_UP_THRESHOLD   11875
  GEN6_RP_DOWN_EI        25000
  GEN6_RP_DOWN_THRESHOLD 21250
 BETWEEN
  GEN6_RP_UP_EI          10156
  GEN6_RP_UP_THRESHOLD    9140
  GEN6_RP_DOWN_EI        25000
  GEN6_RP_DOWN_THRESHOLD 18750
 HIGH_POWER
  GEN6_RP_UP_EI           7812
  GEN6_RP_UP_THRESHOLD    6640
  GEN6_RP_DOWN_EI        25000
  GEN6_RP_DOWN_THRESHOLD 15000

And these are what we have after this patch:
 LOW_POWER
  GEN6_RP_UP_EI          12500
  GEN6_RP_UP_THRESHOLD   11875
  GEN6_RP_DOWN_EI        25000
  GEN6_RP_DOWN_THRESHOLD 21250
 BETWEEN
  GEN6_RP_UP_EI          10175
  GEN6_RP_UP_THRESHOLD    9150
  GEN6_RP_DOWN_EI        25000
  GEN6_RP_DOWN_THRESHOLD 18750
 HIGH_POWER
  GEN6_RP_UP_EI           7825
  GEN6_RP_UP_THRESHOLD    6650
  GEN6_RP_DOWN_EI        25000
  GEN6_RP_DOWN_THRESHOLD 15000

Cc: stable@vger.kernel.org
Cc: Akash Goel <akash.goel@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Testcase: igt/kms_pipe_crc_basic/hang-read-crc-pipe-B
Fixes: 8a586437 ("drm/i915/skl: Restructured the gen6_set_rps_thresholds function")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461159836-9108-1-git-send-email-ville.syrjala@linux.intel.comAcked-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NPatrik Jakobsson <patrik.jakobsson@linux.intel.com>

WaEnableSamplerGPGPUPreemptionSupport fixes a problem
related to mid thread pre-emption.
Signed-off-by: NTim Gore <tim.gore@intel.com>
Reviewed-by: NDave Gordon <david.s.gordon@intel.com>
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461077152-31899-1-git-send-email-tim.gore@intel.com

Do not use magic numbers, do not prefix stuff with "PCI_", do not
declare registers in implementation files. Also move the PCI
registers under correct comment in i915_reg.h.

v2:
- Consistently use BSM (not BDSM or other variants from PRM) (Chris)
- Also include register address to help identify the register (Chris)
v3:
- Refer to register value as *_val instead of *_reg (Chris)
v4:
- Make style checker happy

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

This has been corrected in BSpec quite some time ago, but we missed it
somehow. The wrong field definitions resulted in configuring PHY0 with
an incorrect GRC value.

v2:
- Remove the FIXME comment, we left in the code exactly about this
  issue. (Ville)

CC: Arthur J Runyan <arthur.j.runyan@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-3-git-send-email-imre.deak@intel.com

On CHV GTFIFODBG has some read-only bits to indicate the number
of free FIFO entries. Ignore these when checking to see if any
of the sticky error bits are set.

This gets rid of these during device resume:
[drm:cherryview_enable_rps] GT fifo had a previous error 1080000

While at it, move the assignments out of the if().

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460570970-14073-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

With gen9+ the edram capabilities are defined so
that we can calculate the edram (ellc) size accordingly.

Note that there are undefined combinations for some subset of
edram capability bits. Return the closest size for undefined indexes.
Even if we get it wrong with beginning of future gen enabling, the size
information is currently only used for boot message and in debugfs entry.

v2: Use function instead of hard to read macro (Daniel)
v3: s/INTEL_INFO/INTEL_GEN (Matthew)
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460557604-7126-2-git-send-email-mika.kuoppala@intel.com

Store the edram capabilities instead of only the size of
edram. This is preparatory patch to allow edram size calculation
based on edram capability bits for gen9+. With gen9 the
edram is behind llc and is a separate entity. With hsw/bdw
it was more of a victim cache for LLC so the name 'eLLC' might
be warranted. Regardless, rename all mentions of eLLC to EDRAM to
clear the confusion.

v2: return bytes for edram size (Chris)
    s/eLLC/eDRAM in output if we are gen > 8

v3: rebase, INTEL_GEN (Chris)
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

This is to fix a GPU hang seen with mid thread pre-emption
and pooled EUs.

v2. Use IS_BXT_REVID instead of IS_BROXTON and INTEL_REVID

v3. And use correct type for register addresses
Signed-off-by: NTim Gore <tim.gore@intel.com>
Reviewed-by: NArun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458571049-854-1-git-send-email-tim.gore@intel.com

This patch sets the invert bit for hpd detection for each port
based on VBT configuration. Since each AOB can be designed to
depend on invert bit or not, it is expected if an AOB requires
invert bit, the user will set respective bit in VBT.

v2: Separated VBT parsing from the rest of the logic. (Jani)

v3: Moved setting invert bit logic to bxt_hpd_irq_setup()
    and changed its logic to avoid looping twice. (Ville)

v4: Changed the logic to mask out the bits first and then
    set them to remove need of temporary variable. (Ville)

v5: Moved defines to existing set of defines for the register
    and added required breaks. (Ville)
Signed-off-by: NSivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: NDurgadoss R <durgadoss.r@intel.com>
Signed-off-by: NShubhangi Shrivastava <shubhangi.shrivastava@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
[Jani: fixed some checkpatch noise, added kernel-doc.]
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459420907-11383-2-git-send-email-shubhangi.shrivastava@intel.com

Extract the GPLL reference frequency from CCK and use it in the
GPU freq<->opcode conversions on VLV/CHV. This eliminates all the
assumptions we have about which divider is used for which czclk
frequency.

Note that unlike most clocks from CCK, the GPLL ref clock is a divided
down version of the CZ clock rather than the HPLL clock. CZ clock itself
is a divided down version of the HPLL clock though, so in effect it just
gets divided down twice.

While at it, throw in a few comments explaining the remaining constants
for anyone who later wants to compare this to the spreadsheets.

v2: Add slow/fast notes for CHV clocks (Imre)
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457120584-26080-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com> (v1)

Due to timing issues in the HW, some of the status bits required for GuC
authentication occasionally don't get set; when that happens, the GuC
cannot be initialized and we will be left with a wedged GPU. The W/A
suggested is to perform a soft reset of the GuC and attempt to reload
the F/W again for few times before giving up.

As the failure is dependent on timing, tests performed by triggering
manual full gpu reset (i915_wedged) showed that we could sometimes hit
this after several thousand iterations, but sometimes tests ran even
longer without any issues. Reset and reload mechanism proved helpful
when we indeed hit f/w load failure, so it is better to include this
to improve driver stability.

This change implements the following WAs,

	WaEnableuKernelHeaderValidFix:skl,bxt
	WaEnableGuCBootHashCheckNotSet:skl,bxt
Signed-off-by: NArun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: NDave Gordon <david.s.gordon@intel.com>
Reviewed-by: NAlex Dai <yu.dai@intel.com>
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>

Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/65d58c578adecc205a741102329bc9c9f6eb79cf.1458299160.git.jani.nikula@intel.com

DPLL_MD(PIPE_C) is AWOL on CHV. Instead of fixing it someone added
chicken bits to propagate the pixel multiplier from DPLL_MD(PIPE_B)
to either pipe B or C. So do that to make pixel repeat work on pipes
B and C. Pipe A is fine without any tricks.

Fortunately the pixel repeat propagation appears to be a oneshot
operation, so once the value has been written we can clear the
chicken bits. So it is still possible to drive pipe B and C with
different pixel multipliers simultaneosly.

Looks like DPLL_VGA_MODE_DIS must also be set in DPLL(PIPE_B)
for this to work. But since we keep that bit always set in all
DPLLs there's no problem.

This of course means we can't reliably read out the pixel multiplier
for pipes B and C. That would make the state checker unhappy, so I
added shadow copies of those registers in to dev_priv. The other
option would have been to skip pixel multiplier, dpll_md an dotclock
checks entirely on CHV, but that feels like a serious loss of cross
checking, so just pretending that we have working DPLL MD registers
seemed better. Obviously with the shadow copies we can't detect if
the pixel multiplier was properly configured, nor can we take over
its state from the BIOS, but hopefully people won't have displays
that would be limitd to such crappy modes.

There is one strange flicker still remaining. It's visible on
pipe C/HDMID when HDMIB is enabled while driven by pipe B.
It doesn't occur if pipe A drives HDMIB, nor is there any glitch
on pipe B/HDMIB when port C/HDMID starts up. I don't have a board
with HDMIC so not sure if it happens there too. So I'm not sure
if it's somehow tied in with this strange linkage between pipe B
and C. Sadly I was unable to find an enable sequence that would
avoid the glitch, but at least it's not fatal ie. the output
recovers afterwards.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458052809-23426-4-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

According to the BSpec update, bit 7 of PORT_CL1CM_DW0 register needs to be
checked to ensure that the register is in accessible state.
Also, based on a BSpec update, changing the timeout value to
check iphypwrgood, from 10ms to wait for up to 100us.

v2: [Ville] use wait_for_us instead of the atomic call.
v3: [Jani/Imre] read register only once
Signed-off-by: NVandana Kannan <vandana.kannan@intel.com>
Reported-by: NPhilippe Lecluse <Philippe.Lecluse@intel.com>
Cc: Deak, Imre <imre.deak@intel.com>
Cc: Nikula, Jani <jani.nikula@intel.com>
Acked-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459446354-19012-1-git-send-email-vandana.kannan@intel.com

Currently the machine hangs during booting while accessing the
BXT_MIPI_PORT_CTRL register during pipe HW state readout. After some
experimentation I found that the hang is caused by the DSI PLL being
disabled, or it being enabled but with an incorrect divider
configuration. Enabling the PLL got rid of the boot problem, so fix
this by checking the PLL enabled state/configuration before attempting
to read out the HW state.

The DSI_PLL_ENABLE register is in the always-on power well, while the
BXT_DSI_PLL_CTL is in power well 0. This isn't exactly matched by the
transcoder power domain, but what we really need is just a runtime PM
reference, which is provided by any power domain.

Ville also found this dependency specified in BSpec, so I added a
reference to that too.

v2:
- Make sure we hold a power reference while accessing the PLL registers.
v3: (Jani)
- Simplify check in bxt_get_dsi_transcoder_state()
- Add comment explaining why we check for valid dividers in
  bxt_dsi_pll_is_enabled()

CC: Shashank Sharma <shashank.sharma@intel.com>
CC: Uma Shankar <uma.shankar@intel.com>
CC: Jani Nikula <jani.nikula@intel.com>
Fixes: c6c794a2 ("drm/i915/bxt: Initialize MIPI DSI for BXT")
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NShashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458816100-31269-1-git-send-email-imre.deak@intel.com

This patch contains following changes:
1. Add BXT MIPI display address base.
2. Call dsi_init from display_setup function.

v2: Rebased on latest nightly branch

v3 by Jani: init dsi after ddi
Signed-off-by: NShashank Sharma <shashank.sharma@intel.com>
Signed-off-by: NUma Shankar <uma.shankar@intel.com>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458640910-5338-1-git-send-email-jani.nikula@intel.com

Patch based on a previous series by Shashank Sharma.

v2: Update contributors

v3: Refactor degamma/gamma LUTs load into a single function

v4: Remove unused variable
Signed-off-by: NShashank Sharma <shashank.sharma@intel.com>
Signed-off-by: NKumar, Kiran S <kiran.s.kumar@intel.com>
Signed-off-by: NKausal Malladi <kausalmalladi@gmail.com>
Signed-off-by: NLionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458125837-2576-5-git-send-email-lionel.g.landwerlin@intel.com

Patch based on a previous series by Shashank Sharma.

v2: Do not read GAMMA_MODE register to figure what mode we're in

v3: Program PREC_PAL_GC_MAX to clamp pixel values > 1.0

    Add documentation on how the Broadcast RGB property is affected by CTM

v4: Update contributors

v5: Refactor degamma/gamma LUTs load into a single function

v6: Fix missing intel_crtc variable (bisect issue)

v7: Fix & simplify limited range matrix multiplication (Matt Roper's
    comment)
Signed-off-by: NShashank Sharma <shashank.sharma@intel.com>
Signed-off-by: NKumar, Kiran S <kiran.s.kumar@intel.com>
Signed-off-by: NKausal Malladi <kausalmalladi@gmail.com>
Signed-off-by: NLionel Landwerlin <lionel.g.landwerlin@intel.com>
Acknowledged-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458125837-2576-4-git-send-email-lionel.g.landwerlin@intel.com

This is needed for the Mesa Vulkan driver on Haswell.
Signed-off-by: NJordan Justen <jordan.l.justen@intel.com>
Reviewed-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1457335830-30923-5-git-send-email-jordan.l.justen@intel.com

This allows writes to EU flow control registers. Together
with SIP code from the user-mode driver this resolves a
hang seen in some pre-emption scenarios. Note that this
patch is just the kernel mode part of this workaround.

v2. Oops, add FLOW_CONTROL_ENABLE macro to i915_reg.h.
Signed-off-by: NTim Gore <tim.gore@intel.com>
Reviewed-by: NArun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458144826-17269-1-git-send-email-tim.gore@intel.com

In full gpu reset we prime all engines and reset domains corresponding to
each engine. Per engine reset is just a special case of this process
wherein only a single engine is reset. This change is aimed to modify
relevant functions to achieve this. There are some other steps we carry out
in case of engine reset which are addressed in later patches.

Reset func now accepts a mask of all engines that need to be reset. Where
per engine resets are supported, error handler populates the mask
accordingly otherwise all engines are specified.

v2: ALL_ENGINES mask fixup, better for_each_ring_masked (Chris)
v3: Whitespace fixes (Chris)
v4: Rebase due to s/ring/engine

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NArun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458143640-20563-1-git-send-email-mika.kuoppala@intel.com

BXT isn't as limited as BYT and CHT regarding DSI pipes and ports.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/8bea85b86aaf7a15f854a656bf8d3208a3afe0bd.1458070700.git.jani.nikula@intel.com

The enum mipi_dsi_pixel_format defines MIPI_DSI_FMT_RGB666 for the
"loose" 24 bpp format and MIPI_DSI_FMT_RGB666_PACKED for the 18 bpp
format. We have this the other way round, defining a loose version for
24 bpp.

Follow suit with what's in enum mipi_dsi_pixel_format to avoid future
confusion. Rename

VID_MODE_FORMAT_RGB666 -> VID_MODE_FORMAT_RGB666_PACKED
VID_MODE_FORMAT_RGB666_LOOSE -> VID_MODE_FORMAT_RGB666
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458123700-16003-1-git-send-email-jani.nikula@intel.com

Currently we assume that hrawclk is 200MHz on VLV/CHV. That should
be true always, but just to avoid such asumptions we can read out the
actual frequency from CCK.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1456932138-14004-5-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

The MIPI clock calculations for the addtional clock
are revised from B0 stepping onwards, the bit definitions
have changed compared to old stepping.

v2: Fixing compilation warning.
v3: Retained the old Macros (Jani)
Signed-off-by: NDeepak M <m.deepak@intel.com>
Tested-by: Ramalingam C <ramalingam.c@intel.com> # BXT-T with Tianma panel
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455556437-29267-1-git-send-email-m.deepak@intel.com

Rather than assume the VGA dotclock is really the FDI based thing,
let's read out the real thing via iclkip, and after readout it'll
get to compare it with the FDI based number to make sure they're
in sync.

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455738073-14502-6-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

Cores need to be included into the debug mask. We don't exactly
know what it does but the spec says it must be enabled. So obey.

v2: Cores should be only set for BXT (Imre, Art)

Cc: Imre Deak <imre.deak@intel.com>
Cc: Runyan, Arthur J <arthur.j.runyan@intel.com>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455877564-5128-1-git-send-email-mika.kuoppala@intel.com

Looks like g4x hpd live status bits actually agree with the spec. At
least they do on the machine I have, and apparently on Nick Bowler's
g4x as well.

So gm45 may be the only platform where they don't agree. At least
that seems to be the case based on the (somewhat incomplete)
logs/dumps in [1], and Daniel has also tested this on his gm45
sometime in the past.

So let's change the bits to match the spec on g4x. That actually makes
the g4x bits identical to vlv/chv so we can just share the code
between those platforms, leaving gm45 as the special case.

[1] https://bugzilla.kernel.org/show_bug.cgi?id=52361

Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Nick Bowler <nbowler@draconx.ca>
References: https://lists.freedesktop.org/archives/dri-devel/2016-February/100382.htmlReported-by: NNick Bowler <nbowler@draconx.ca>
Cc: stable@vger.kernel.org
Fixes: 237ed86c ("drm/i915: Check live status before reading edid")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455127145-20087-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 0780cd36)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>