This patch adds new iface type (NL80211_IFTYPE_OCB) representing
the OCB (Outside the Context of a BSS) mode.
When establishing a connection to the network a cfg80211_join_ocb
function is called (particular nl80211_command is added as well).
A mandatory parameters during the ocb_join operation are 'center
frequency' and 'channel width (5/10 MHz)'.

Changes done in mac80211 are minimal possible required to avoid
many warnings (warning: enumeration value 'NL80211_IFTYPE_OCB'
not handled in switch) during compilation. Full functionality
(where needed) is added in the following patch.
Signed-off-by: NRostislav Lisovy <rostislav.lisovy@fel.cvut.cz>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When freeing the connect keys, clear the memory to avoid
having the key material stick around in memory "forever".
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Our legal structure changed at some point (see wikipedia), but
we forgot to immediately switch over to the new copyright
notice.

For files that we have modified in the time since the change,
add the proper copyright notice now.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Implement and export the new cfg80211_get_station() API.
This utility can be used by other kernel modules to obtain
detailed information about a given wireless station.

It will be in particular useful to batman-adv which will
implement a wireless rate based metric.
Signed-off-by: NAntonio Quartulli <antonio@open-mesh.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This also propagates through the drivers.

The orinoco driver uses the cfg80211 API structs for internal
bookkeeping, and so needs a (void *) cast that removes the
const - but that's OK because it allocates those pointers.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

At the moment, the ath9k/ath10k DFS module only supports detecting ETSI
radar patterns.
Add a bitmap in the interface combinations, indicating which DFS regions
are supported by the detector. If unset, support for all regions is
assumed.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This exports a new cfg80211_stop_iface() function.

This is intended for driver internal interface
combination management and channel switching.

Due to locking issues (it re-enters driver) the
call is asynchronous and uses cfg80211 event
list/worker.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Name wiphy_to_rdev is more accurate to describe what the function
does, i.e., return a pointer pointing to struct
cfg80211_registered_device.
Signed-off-by: NZhao, Gang <gamerh2o@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The patch splits cfg80211_check_combinations()
into an iterator function and a simple iteration
user.

This makes it possible for drivers to asses how
many channels can use given iftype setup. This in
turn can be used for future
multi-interface/multi-channel channel switching.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

All bits from radar_detect must match combination
radar bitmask. Otherwise it is theoretically
possible to lead into an invalid combination
provided a driver reports strange combinations.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Get rid of the cfg80211_can_add_interface() and
cfg80211_can_change_interface() functions by moving that functionality
to mac80211.  With this patch all interface combination checks are now
out of cfg80211 (except for the channel switch case which will be
addressed in a future commit).

Additionally, modify the ieee80211_check_combinations() function so
that an undefined chandef can be passed, in order to use it before a
channel is defined.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Move the counting part of the interface combination check from
cfg80211 to mac80211.

This is needed to simplify locking when the driver has to perform a
combination check by itself (eg. with channel-switch).
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Separate the code that counts the interface types and channels from
the code that check the interface combinations.  The new function that
checks for combinations is exported so it can be called by the
drivers.

This is done in preparation for moving the interface combinations
checks out of cfg80211.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Macro ASSERT_RDEV_LOCK(rdev) is equal to ASSERT_RTNL(), so replace it
with ASSERT_RTNL() and remove it.
Signed-off-by: NZhao, Gang <gamerh2o@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

MPLS labels may contain traffic control information, which should be
evaluated and used by the wireless subsystem if present.

Also check for IEEE 802.21 which is always network control traffic.
Signed-off-by: NSimon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit "nl80211: send event when AP operation is stopped" added an
event to notify user space that an AP interface has been stopped, to
handle cases such as suspend etc. The event is sent regardless
if the stop AP flow was triggered by user space or due to internal state
change.

This might cause issues with wpa_supplicant/hostapd flows that consider
stop AP flow as a synchronous one, e.g., AP/GO channel change in the
absence of CSA support. In such cases, the flow will restart the AP
immediately after the stop AP flow is done, and only handle the stop
AP event after the current flow is done, and as a result stop the AP
again.

Change the current implementation to only send the event in case the
stop AP was triggered due to an internal reason.
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

We don't have to double check whether the parameters passed to
cfg80211_can_use_iftype_chan() are correct.  We should just make sure
they *are* when we call this function.

Remove the radar_detect argument check in
cfg80211_can_use_iftype_chan() to simplify the code.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
[keep braces around a long comment + single statement]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

It was possible to break interface combinations in
the following way:

 combo 1: iftype = AP, num_ifaces = 2, num_chans = 2,
 combo 2: iftype = AP, num_ifaces = 1, num_chans = 1, radar = HT20

With the above interface combinations it was
possible to:

 step 1. start AP on DFS channel by matching combo 2
 step 2. start AP on non-DFS channel by matching combo 1

This was possible beacuse (step 2) did not consider
if other interfaces require radar detection.

The patch changes how cfg80211 tracks channels -
instead of channel itself now a complete chandef
is stored.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When receiving an IBSS_JOINED event select the BSS object
based on the {bssid, channel} couple rather than the bssid
only.
With the current approach if another cell having the same
BSSID (but using a different channel) exists then cfg80211
picks up the wrong BSS object.
The result is a mismatching channel configuration between
cfg80211 and the driver, that can lead to any sort of
problem.

The issue can be triggered by having an IBSS sitting on
given channel and then asking the driver to create a new
cell using the same BSSID but with a different frequency.
By passing the channel to cfg80211_get_bss() we can solve
this ambiguity and retrieve/create the correct BSS object.
All the users of cfg80211_ibss_joined() have been changed
accordingly.

Moreover WARN when cfg80211_ibss_joined() gets a NULL
channel as argument and remove a bogus call of the same
function in ath6kl (it does not make sense to call
cfg80211_ibss_joined() with a zero BSSID on ibss-leave).

Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: Bing Zhao <bzhao@marvell.com>
Cc: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Cc: libertas-dev@lists.infradead.org
Acked-by: NKalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: NAntonio Quartulli <antonio@open-mesh.com>
[minor code cleanup in ath6kl]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add a utility function to get the number of channels supported by
the device, and update the places in the code that need this data.
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
[replace another occurrence in libertas, fix kernel-doc, fix bugs]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Since the RTNL can't always be held, use wdev/sdata locking for
the qos-map dereference in mac80211. This requires cfg80211 to
consistently lock it, which it was missing in one place.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This allows QoS mapping from external networks to be implemented as
defined in IEEE Std 802.11-2012, 10.24.9. APs can use this to advertise
DSCP ranges and exceptions for mapping frames to a specific UP over
Wi-Fi.

The payload of the QoS Map Set element (IEEE Std 802.11-2012, 8.4.2.97)
is sent to the driver through the new NL80211_ATTR_QOS_MAP attribute to
configure the local behavior either on the AP (based on local
configuration) or on a station (based on information received from the
AP).
Signed-off-by: NKyeyoon Park <kyeyoonp@qca.qualcomm.com>
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

To use DFS in IBSS mode, userspace is required to react to radar events.
It can inform nl80211 that it is capable of doing so by adding a
NL80211_ATTR_HANDLE_DFS attribute when joining the IBSS.

This attribute is supplied to let the kernelspace know that the
userspace application can and will handle radar events, e.g. by
intiating channel switches to a valid channel. DFS channels may
only be used if this attribute is supplied and the driver supports
it. Driver support will be checked even if a channel without DFS
will be initially joined, as a DFS channel may be chosen later.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[fix attribute name in commit message]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If the VLAN tci is set in skb->vlan_tci use the
priority field to determine the WMM priority.
Signed-off-by: Ncedric Voncken <cedric.voncken@acksys.fr>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Mandatory rates for 5 and 10 MHz are different from the rates used for
20 MHz in 2.4 GHz mode, as they use OFDM only.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>

By making all the API functions require wdev locking we
can clean up the API a bit, getting rid of the locking
version of each function. This also decreases the size
of cfg80211 by a small amount.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Virtually all code paths in cfg80211 already (need to) hold
the RTNL. As such, there's little point in having another
four mutexes for various parts of the code, they just cause
lock ordering issues (and much of the time, the RTNL and a
few of the others need thus be held.)

Simplify all this by getting rid of the extra four mutexes
and just use the RTNL throughout. Only a few code changes
were needed to do this and we can get rid of a work struct
for bonus points.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Move mandatory rates calculation to cfg80211, shared with non mac80211 drivers.
Signed-off-by: NAshok Nagarajan <ashok@cozybit.com>
[extend documentation]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add regulatory class for 60GHz band, according
to the last specification.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In cfg80211_can_use_iftype_chan(), check for P2P Device
first, and then for netdevs. This doesn't really change
anything but makes the code a bit easier to read since
it may not be obvious for everyone at first that a P2P
device has no netdev.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This function converts a (global only!) operating
class to an internal band identifier. This will
be needed for extended channel switch support.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add a new constant ETH_P_802_3_MIN, the minimum ethernet type for
an 802.3 frame. Frames with a lower value in the ethernet type field
are Ethernet II.

Also update all the users of this value that David Miller and
I could find to use the new constant.

Also correct a bug in util.c. The comparison with ETH_P_802_3_MIN
should be >= not >.

As suggested by Jesse Gross.

Compile tested only.

Cc: David Miller <davem@davemloft.net>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Bart De Schuymer <bart.de.schuymer@pandora.be>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Cc: netfilter-devel@vger.kernel.org
Cc: bridge@lists.linux-foundation.org
Cc: linux-wireless@vger.kernel.org
Cc: linux1394-devel@lists.sourceforge.net
Cc: linux-media@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: dev@openvswitch.org
Acked-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Radar is not required for P2P_DEVICE interfaces.
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In commit "cfg80211: check radar interface combinations" a regression
was introduced which might lead to NULL dereference if the argument
chan = NULL, which might happen in IBSS/wext case (and probably
others).
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

To ease further DFS development regarding interface combinations, use
the interface combinations structure to test for radar capabilities.
Drivers can specify which channel widths they support, and in which
modes. Right now only a single AP interface is allowed, but as the
DFS code evolves other combinations can be enabled.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When a BSS struct is updated, the IEs are currently
overwritten or freed. This can lead to races if some
other CPU is accessing the BSS struct and using the
IEs concurrently.

Fix this by always allocating the IEs in a new struct
that holds the data and length and protecting access
to this new struct with RCU.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add support for reporting and calculating VHT MCSes.

Note that I'm not completely sure that the bitrate
calculations are correct, nor that they can't be
simplified.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The function cfg80211_get_p2p_attr() can fail and returns
a negative error code. However, the return type is unsigned
int. The largest positive number is determined by desired_len
variable in the function, which is u16. So changing the return
type to int to allow easy error checking. Also change the type
for the attribute to enum for improved type checking.
Signed-off-by: NArend van Spriel <arend@broadcom.com>
[fix indentation, don't use u8 attr variable]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Parsing the P2P attributes can be tricky as their
contents can be split across multiple (vendor) IEs.
Thus, it's not possible to parse them like IEs (by
returning a pointer to the data.) Instead, provide
a function that copies the attribute data into a
caller-provided buffer and returns the size needed
(useful in case the buffer was too small.)
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

A number of places in the mesh code don't check that
the frame data is present and in the skb header when
trying to access. Add those checks and the necessary
pskb_may_pull() calls. This prevents accessing data
that doesn't actually exist.

To do this, export ieee80211_get_mesh_hdrlen() to be
able to use it in mac80211.

Cc: stable@vger.kernel.org
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>