- 13 2月, 2010 2 次提交
-
-
由 Joe Perches 提交于
Convert uses of msg_<type> to netif_<level>( Remove msg_<type> macros Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jiri Pirko 提交于
This patch replaces dev->mc_count in all drivers (hopefully I didn't miss anything). Used spatch and did small tweaks and conding style changes when it was suitable. Jirka Signed-off-by: NJiri Pirko <jpirko@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 08 1月, 2010 1 次提交
-
-
由 Alexey Dobriyan 提交于
Use DEFINE_PCI_DEVICE_TABLE() so we get place PCI ids table into correct section in every case. Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 04 12月, 2009 1 次提交
-
-
由 Joe Perches 提交于
Only files where David Miller is the primary git-signer. wireless, wimax, ixgbe, etc are not modified. Compile tested x86 allyesconfig only Not all files compiled (not x86 compatible) Added a few > 80 column lines, which I ignored. Existing checkpatch complaints ignored. Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 20 11月, 2009 1 次提交
-
-
由 Joe Perches 提交于
Changed function pointer use from non-majority address-of style to majority short form without & via: (was: 8 with &, 36 without) grep -rPl "\btasklet_init\s*\([^,\)]+,\s*\&" drivers/net | while read file ; do \ perl -i -e 'local $/; while (<>) { s@(\btasklet_init\s*\([^,\)]+,\s*)\&@\1@g ; print ; }' $file ;\ done Compile tested allyesconfig x86 Signed-off-by: NJoe Perches <joe@perches.com> drivers/net/cnic.c | 4 ++-- drivers/net/jme.c | 10 +++++----- drivers/net/skge.c | 2 +- 3 files changed, 8 insertions(+), 8 deletions(-) Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 01 9月, 2009 1 次提交
-
-
由 Stephen Hemminger 提交于
In a couple of cases collapse some extra code like: int retval = NETDEV_TX_OK; ... return retval; into return NETDEV_TX_OK; Signed-off-by: NStephen Hemminger <shemminger@vyatta.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 07 7月, 2009 5 次提交
-
-
由 Guo-Fu Tseng 提交于
1. Use more efficient way to determine flag status. 2. Hardware dose not mark fragment bit against IPv6 packets, print TCP/UDP checksum warning message for IPv4 packets only. Signed-off-by: NGuo-Fu Tseng <cooldavid@cooldavid.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Guo-Fu Tseng 提交于
The hardware failed to update the shadow register in several cases. It's known to be failed at 64bit box with more than 4G RAM. In order to make the device working stable, give up using the shadow register feature. Signed-off-by: NGuo-Fu Tseng <cooldavid@cooldavid.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Guo-Fu Tseng 提交于
Instead of using a large chunk of memory space preserved for for modules, using kmalloc to obtain the needed memory. Signed-off-by: NGuo-Fu Tseng <cooldavid@cooldavid.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Guo-Fu Tseng 提交于
Fix faulty tasklet function usage. Signed-off-by: NGuo-Fu Tseng <cooldavid@cooldavid.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Guo-Fu Tseng 提交于
Making coding style more consistent. Signed-off-by: NGuo-Fu Tseng <cooldavid@cooldavid.org> Signed-off-by: NGuo-Fu Tseng <cooldavid@cooldavid.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 29 5月, 2009 1 次提交
-
-
由 Eric Dumazet 提交于
Second round of drivers for Gb cards (and NIU one I forgot in the 10GB round) Now that core network takes care of trans_start updates, dont do it in drivers themselves, if possible. Drivers can avoid one cache miss (on dev->trans_start) in their start_xmit() handler. Exceptions are NETIF_F_LLTX drivers Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 14 4月, 2009 1 次提交
-
-
由 Yang Hongyang 提交于
This is the second go through of the old DMA_nBIT_MASK macro,and there're not so many of them left,so I put them into one patch.I hope this is the last round. After this the definition of the old DMA_nBIT_MASK macro could be removed. Signed-off-by: NYang Hongyang <yanghy@cn.fujitsu.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Tony Lindgren <tony@atomide.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Cc: Greg KH <greg@kroah.com> Cc: Takashi Iwai <tiwai@suse.de> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 07 4月, 2009 1 次提交
-
-
由 Yang Hongyang 提交于
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32) Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 04 3月, 2009 1 次提交
-
-
由 Roel Kluin 提交于
with while (timeout-- > 0); timeout reaches -1 after the loop, so the tests below are off by one. also don't do an '< 0' test on an unsigned. Signed-off-by: NRoel Kluin <roel.kluin@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 02 3月, 2009 4 次提交
-
-
由 Guo-Fu Tseng 提交于
All JMC250 chips have no problem with higher bits support. Adding it back. Found-by: NEthan Hsiao <ethanhsiao@jmicron.com> Signed-off-by: NGuo-Fu Tseng <cooldavid@cooldavid.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Guo-Fu Tseng 提交于
Clear all modified GHC register flags. Fixed-by: NEthan Hsiao <ethanhsiao@jmicron.com> Signed-off-by: NGuo-Fu Tseng <cooldavid@cooldavid.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Guo-Fu Tseng 提交于
We should sync ring descriptor to pci device after modifying it. Signed-off-by: NGuo-Fu Tseng <cooldavid@cooldavid.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Guo-Fu Tseng 提交于
This patch modifies messages to display correct hardware version. Signed-off-by: NGuo-Fu Tseng <cooldavid@cooldavid.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 23 12月, 2008 1 次提交
-
-
由 Neil Horman 提交于
When the napi api was changed to separate its 1:1 binding to the net_device struct, the netif_rx_[prep|schedule|complete] api failed to remove the now vestigual net_device structure parameter. This patch cleans up that api by properly removing it.. Signed-off-by: NNeil Horman <nhorman@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 04 12月, 2008 2 次提交
-
-
由 Guo-Fu Tseng 提交于
Although the hardware supports the 64bit DMA address in design, but later found that it actually not working. This patch reduced the rang to 32bit. Found-by: N"Ethan" <ethanhsiao@jmicron.com> Signed-off-by: N"Guo-Fu Tseng" <cooldavid@cooldavid.org> Acked-by: NJeff Garzik <jgarzik@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 akeemting 提交于
Due to the hardware design, except the first chip on the market, other chips needs to setup the clock source for MAC processor implicitly through Global Host Control Register(GHC). (Strange design huh?) 10/100M uses the PCI-E as clock source, and 1G uses GPHY. And I reordered the code a little, to make it easier to read. Found-by: N"Ethan" <ethanhsiao@jmicron.com> Fixed-by: N"akeemting" <akeem@jmicron.com> Signed-off-by: N"Guo-Fu Tseng" <cooldavid@cooldavid.org> Acked-by: NJeff Garzik <jgarzik@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 22 11月, 2008 1 次提交
-
-
由 Stephen Hemminger 提交于
Convert driver to new net_device_ops. Compile tested only. Signed-off-by: NStephen Hemminger <shemminger@vyatta.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 20 11月, 2008 1 次提交
-
-
由 Harvey Harrison 提交于
This is the minimal patch to fix endian mismatches. These are probably bugs on big-endian arches, noops on little endian. jme_rxsum_ok could be improved to directly take a __le16 and change all of the masks/sets to be in little-endian, but has not been done here to keep the patch small. Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 04 11月, 2008 1 次提交
-
-
由 David S. Miller 提交于
The generic packet receive code takes care of setting netdev->last_rx when necessary, for the sake of the bonding ARP monitor. Drivers need not do it any more. Some cases had to be skipped over because the drivers were making use of the ->last_rx value themselves. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 28 10月, 2008 1 次提交
-
-
由 Johannes Berg 提交于
A number of places still use %02x:...:%02x because it's in debug statements or for no real reason. Make a few of them use %pM. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 14 10月, 2008 1 次提交
-
-
由 Kamalesh Babulal 提交于
2.6.27-git2 kernel build fails with allyesconfig on powerpc with build error <introduced by commit 01f2e4ea> CC drivers/net/enic/enic_main.o drivers/net/enic/enic_main.c: In function âenic_queue_wq_skb_tsoâ: drivers/net/enic/enic_main.c:576: error: implicit declaration of function âcsum_ipv6_magicâ make[3]: *** [drivers/net/enic/enic_main.o] Error 1 <introduced by commit c4e84bde> drivers/net/qlge/qlge_main.c: In function âql_tsoâ: drivers/net/qlge/qlge_main.c:1862: error: implicit declaration of function âcsum_ipv6_magicâ make[3]: *** [drivers/net/qlge/qlge_main.o] Error 1 <introduced by commit 95252236> drivers/net/jme.c: In function âjme_tx_tsoâ: drivers/net/jme.c:1784: error: implicit declaration of function âcsum_ipv6_magicâ make[2]: *** [drivers/net/jme.o] Error 1 Signed-off-by: NKamalesh Babulal <kamalesh@linux.vnet.ibm.com> Signed-off-by: NRon Mercer <ron.mercer@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 13 10月, 2008 1 次提交
-
-
由 Huang Weiyi 提交于
The file(s) below do not use LINUX_VERSION_CODE nor KERNEL_VERSION. drivers/net/jme.c This patch removes the said #include <version.h>. Signed-off-by: NHuang Weiyi <weiyi.huang@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 09 10月, 2008 3 次提交
-
-
由 David S. Miller 提交于
drivers/net/jme.c:1598: warning: ‘jme_set_100m_half’ defined but not used drivers/net/jme.c:1618: warning: ‘jme_wait_link’ defined but not used Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 akeemting 提交于
Fix IRQ handle bug when interrupt mode. The driver was incorrectly handled and returned IRQ_HANDLED while the device is not generating the interrupt. It happened due to faulty determination of interrupt status register. Found by: "Ethan" <ethanhsiao@jmicron.com> Fixed by: "akeemting" <akeem@jmicron.com> Signed-off-by: NGuo-Fu Tseng <cooldavid@cooldavid.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Guo-Fu Tseng 提交于
1. Set bit 5 of GPREG1 to 1 to enable hardware workaround for half-duplex mode. Which the MAC processor generates CRS/COL by itself instead of receive it from PHY processor. 2. Set bit 6 of GPREG1 to 1 to enable hardware workaround that masks the MAC processor working right while calculating IPv6 RSS in 10/100 mode. 3. Group the workaround codes all together. Signed-off-by: NGuo-Fu Tseng <cooldavid@cooldavid.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 18 9月, 2008 1 次提交
-
-
由 Guo-Fu Tseng 提交于
Supporting JMC250, and JMC260. Signed-off-by: NGuo-Fu Tseng <cooldavid@cooldavid.org> Acked-and-tested-by: NEthan Hsiao <ethanhsiao@jmicron.com> Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
-