MPC8323EMDS board ethernet interface with RMII uses the CLK16 divisor
for the rx and tx clock, but the ucc_set_qe_mux_rxtx() function doesn't
handle the CLK16 setting of the CMXUCR3 and CMXUCR4 registers.  This
fixes it.
Signed-off-by: NDave Liu <daveliu@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

===================================================================
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Currently, spufs_mbox_read transfers more bytes than requested on a
read.  If you ask for four bytes, you get eight.  This fixes it to
transfer the largest multiple of four bytes that is less than or equal
to the number you asked for.

Note: one nasty property of this file in spufs is that you can only
read multiples of four bytes in the first place, since there is no way
to atomically put back a few bytes into the hardware register.  Thus,
reading less than four bytes returns -EINVAL.  Asking for more than
four returns the largest possible multiple of four.
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This fixes the /signal2 file to actually give signal2 data.
Signed-off-by: NDwayne Grant Mcconnell <decimal@us.ibm.com>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Fix a const'ification related warning with device_is_compatible()
and friends related to get_property() not properly having const
on it's input device node argument.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The Cell CPU timebase has an erratum. When reading the entire 64 bits
of the timebase with one mftb instruction, there is a handful of cycles
window during which one might read a value with the low order 32 bits
already reset to 0x00000000 but the high order bits not yet incremeted
by one. This fixes it by reading the timebase again until the low order
32 bits is no longer 0. That might introduce occasional latencies if
hitting mftb just at the wrong time, but no more than 70ns on a cell
blade, and that was considered acceptable.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch adds support for feature fixups in modules. This involves
adding support for R_PPC64_REL64 relocs to the 64 bits module loader.
It also modifies modpost.c to ignore the powerpc fixup sections (or it
would warn when used in .init.text).
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch reworks the feature fixup mecanism so vdso's can be fixed up.
The main issue was that the construct:

        .long   label  (or .llong on 64 bits)

will not work in the case of a shared library like the vdso. It will
generate an empty placeholder in the fixup table along with a reloc,
which is not something we can deal with in the vdso.

The idea here (thanks Alan Modra !) is to instead use something like:

1:
        .long   label - 1b

That is, the feature fixup tables no longer contain addresses of bits of
code to patch, but offsets of such code from the fixup table entry
itself. That is properly resolved by ld when building the .so's. I've
modified the fixup mecanism generically to use that method for the rest
of the kernel as well.

Another trick is that the 32 bits vDSO included in the 64 bits kernel
need to have a table in the 64 bits format. However, gas does not
support 32 bits code with a statement of the form:

        .llong  label - 1b  (Or even just .llong label)

That is, it cannot emit the right fixup/relocation for the linker to use
to assign a 32 bits address to an .llong field. Thus, in the specific
case of the 32 bits vdso built as part of the 64 bits kernel, we are
using a modified macro that generates:

        .long   0xffffffff
        .llong  label - 1b

Note that is assumes that the value is negative which is enforced by
the .lds (those offsets are always negative as the .text is always
before the fixup table and gas doesn't support emiting the reloc the
other way around).
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

There are currently two versions of the functions for applying the
feature fixups, one for CPU features and one for firmware features. In
addition, they are both in assembly and with separate implementations
for 32 and 64 bits. identify_cpu() is also implemented in assembly and
separately for 32 and 64 bits.

This patch replaces them with a pair of C functions. The call sites are
slightly moved on ppc64 as well to be called from C instead of from
assembly, though it's a very small change, and thus shouldn't cause any
problem.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

In ucc_fast.c and ucc_slow.c, "illegal" is twice spelled "illagal".
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Don't require that the wrapper script be executable when building
zImage.initrds.  This has already been fixed for zImages.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

970GX cputable entry from Steve Winiecki.
Signed-off-by: NJake Moilanen <moilanen@austin.ibm.com>

 arch/powerpc/kernel/cputable.c          |   15 +++++++++++++++
 arch/powerpc/oprofile/op_model_power4.c |    2 +-
 include/asm-powerpc/reg.h               |    1 +
 3 files changed, 17 insertions(+), 1 deletion(-)
Signed-off-by: NPaul Mackerras <paulus@samba.org>

low_cpu_die is called from the CPU hotplug code on 32-bit powermacs,
but it is only defined if CONFIG_PM || CONFIG_CPU_FREQ_PMAC.  This
changes the ifdef so it is defined for CONFIG_HOTPLUG_CPU on 32-bit
machines.
Signed-off-by: NSrinivasa DS <srinivasa@in.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This fixes the warning message from the return value of function
get_property(), by making sure that the variable that receives the
value is marked as const.
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>

--
Signed-off-by: NPaul Mackerras <paulus@samba.org>

In calculating stolen time, we were trying to actually account for time
spent in the hypervisor.  We don't really have enough information to do
that accurately, so don't try.  Instead, we now calculate stolen time as
time that the current cpu thread is not actually dispatching instructions.
On chips without a PURR, we cannot do this, so stolen time will always
be zero.  On chips with a PURR, this is merely the difference between
the elapsed PURR values and the elapsed TB values.

This gives us much more sane vaules from tools such as mpstat, even if
they are still a bit strange e.g. 2 busy threads on one cpu will both
appear to have 50% user time and 50% stolen time while 1 busy thread on
a cpu will look like 100% user on one of them and 100% idle on the other.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Reintroduce NODES_SPAN_OTHER_NODES for powerpc

Revert "[PATCH] Remove SPAN_OTHER_NODES config definition"
    This reverts commit f62859bb.
Revert "[PATCH] mm: remove arch independent NODES_SPAN_OTHER_NODES"
    This reverts commit a94b3ab7.

Also update the comments to indicate that this is still required
and where its used.
Signed-off-by: NAndy Whitcroft <apw@shadowen.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Mike Kravetz <kravetz@us.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NMel Gorman <mel@csn.ul.ie>
Acked-by: NWill Schmidt <will_schmidt@vnet.ibm.com>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

During boot we bring up all memory and cpu nodes. Normally a PCI device
will be in one of these online nodes, however in some weird setups it
may not.

We have only seen this in the lab but we may as well check for the case
and fallback to -1 (all nodes).
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Instead of just checking that an address is in the right range, use the
provided __kernel_text_address() helper which covers both the kernel and
module text sections.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Change ->num_pmcs to match the number of PMCs in POWER6.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

At the moment we rely on a cpu feature bit or a firmware property to
detect altivec. If we dont have either of these and the cpu does in fact
support altivec we can cause a panic from userspace.

It seems safer to always send a signal if we manage to get an 0xf20
exception from userspace.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

When update_bridge_base() updates the IO window on a PCI-to-PCI
bridge, it fails to zero the upper 16 bits of the base and limit
registers if the window size is less than 64K.  This fixes it.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Add missing entry in Makefile for MPC832x MDS support.  It
also change white space to tab in MPC8360 entry.
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

MPC8360EMDS PB support is broken as some code was missing
in last submission.  This patch adds missing code and makes
MPC8360EMDS PB support working.
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The default configuration file for the MPC8349E-mITX reference board,
mpc834x_itx_defconfig, did not include support for DOS partition table types.
This support is necessary because the hard drive that comes with the ITX
is formatted with this partition table type.  Without this config option,
no partitions on the drive can be mounted.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This fixes a memory leak introduced by "spufs: add support
for read/write oncntl", which was missing a call to simple_attr_close.
Signed-off-by: NMasato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The SPU code will crash if CONFIG_NUMA is not set and SPUs are found on
a non-0 node. This workaround will ignore those SPEs and just print an
message in the kernel log.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Arch-independent zone-sizing is using indices instead of symbolic names to
offset within an array related to zones (max_zone_pfns).  The unintended
impact is that ZONE_DMA and ZONE_NORMAL is initialised on powerpc instead
of ZONE_DMA and ZONE_HIGHMEM when CONFIG_HIGHMEM is set.  As a result, the
the machine fails to boot but will boot with CONFIG_HIGHMEM turned off.

The following patch properly initialises the max_zone_pfns[] array and uses
symbolic names instead of indices in each architecture using
arch-independent zone-sizing.  Two users have successfully booted their
powerpcs with it (one an ibook G4).  It has also been boot tested on x86,
x86_64, ppc64 and ia64.  Please merge for 2.6.19-rc2.

Credit to Benjamin Herrenschmidt for identifying the bug and rolling the
first fix.  Additional credit to Johannes Berg and Andreas Schwab for
reporting the problem and testing on powerpc.
Signed-off-by: NMel Gorman <mel@csn.ul.ie>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

On the old "powersurge" SMP powermacs, the second CPU is started up
by sending it an IPI, which has the side effect of stopping the
timebase clock (so the secondary CPU's timebase can be synchronized
with the primary's).  The routine that did this used udelay, which
will hang forever when the timebase is stopped, since udelay now spins
until the timebase reaches a certain value.

The end result is that the kernel would hang when bringing up the
second CPU.  This fixes it by using a simple loop which just does a
fixed number of iterations to generate the delay.  These old systems
were all clocked at around 200 MHz or so, so a fixed number of
iterations is acceptable.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This updates the Maple defconfig to 4 CPUs (along with current defaults)
to support the "tigerwood" 970MP evaluation board.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The IDE driver will pick up the PCI IRQ for both channels on Maple
despite the fact that it's in legacy mode. This works around it by
"hiding" the PCI IRQ of the AMD8111 IDE controller when it's configured
in legacy mode on the Maple platform, thus causing the driver to call
pci_get_legacy_ide_irq() which will return the correct interrupts for
both channels.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The Maple support code was missing code for U4/CPC945 PCIe. This adds
it, enabling it to work on tigerwood boards, and possibly also js21
using SLOF. Also disable an obsolete firmware workaround.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Change CONFIG_PPC_CELL to CONFIG_PPC_IBM_CELL_BLADE in the powerpc boot
makefile.

CONFIG_PPC_CELL is used to build the generic cell processor support, and
is not an indication of platform.
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

My CROSS_COMPILE is "ccache /opt/compilers/blah", which confuses
the boot wrapper script. Quote CROSS_COMPILE and CROSS32_COMPILE
so they can safely contain spaces.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NDave Jones <davej@redhat.com>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Use the new typedef for interrupt handler function pointers rather than
actually spelling out the full thing each time.  This was scripted with the
following small shell script:

#!/bin/sh
egrep -nHrl -e 'irqreturn_t[ 	]*[(][*]' $* |
while read i
do
    echo $i
    perl -pi -e 's/irqreturn_t\s*[(]\s*[*]\s*([_a-zA-Z0-9]*)\s*[)]\s*[(]\s*int\s*,\s*void\s*[*]\s*[)]/irq_handler_t \1/g' $i || exit $?
done
Signed-Off-By: NDavid Howells <dhowells@redhat.com>

This reverts commit 41550c51.

Quoth Ben Herrenschmidt:
 "Please revert this one for now.  It seems to break G5s :( Looks like
  PCI cells inside Apple IO ASICs don't have a PCI_INTERRUPT_LINE set.
  I need to figure out a better fix."
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Remove struct pt_regs * from remaining spu irq functions.
Signed-off-by: NOlaf Hering <olaf@aepfle.de>
Signed-off-by: NPaul Mackerras <paulus@samba.org>