Moves the Brocade driver into drivers/net/ethernet/brocade/ and make
the necessary Kconfig and Makefile changes.

CC: Rasesh Mody <rmody@brocade.com>
CC: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Change details:
 - Introducing new file bfi_reg.h for consolidating all supported hardware
   registers. This file completely replaces bfi_ctreg.h.
 - Updated ioc code as per register definition change.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
 - Heartbeat failure counter is not incrementing under some scenarios.
   Update hbfails and hb_count stats during hwerror event.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
 - Added logic to unlock hw semaphore if the previos FW boot was from boot
   code (flash based) and the current FW initialization attempt is from OS
   driver.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
 - Changed event name IOC_E_PFAILED to IOC_E_PFFAILED
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
 - If there is a command pending in the mailbox, bfa_ioc_mbox_queue() enqueues
   the mailbox command to a pending command queue. Entries in this queue are
   not flushed when IOC is disabled. As a result, when IOC is re-enabled again,
   the stale entries in the pending command queue are posted to the mailbox.
   When these mailbox commands are processed by the FW and responses are sent,
   unexpected  events are received by other modules' FSMs (f.e. bfa_msgq) which
   have not posted any mailbox commands after IOC was enabled.
 - Flush the pending mailbox command queue when IOC is disabled. Rename
   bfa_ioc_mbox_hbfail to bfa_ioc_mbox_flush. Call bfa_ioc_mbox_flush
   from bfa_iocpf_sm_disabled_entry()
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Chnage details:
 - The module name is not used in case of state machine fault, hence no longer
   passing the module name to the fault handler.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
 - Replace IOC HB failure event notification with a more generic mechanism
   that is capable of sending enble, disable, and failed events to registered
   modules. As a result, cee  module event handling callback bfa_cee_hbfail()
   is replaced with bfa_cee_notify() so that it can receive and handle
   different events from IOC.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
 - Driver cleanup as per new checkpatch v0.31
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the below compile warning:

drivers/net/bna/bfa_ioc.c:1922: warning: ‘bfa_ioc_smem_pgoff’ defined but not used
Signed-off-by: NShan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The variable 'pgoff' is set but unused in bfa_nw_ioc_fwver_get()
and bfa_ioc_download_fw().

Similarly for 'cmd_h' in bna_mbox_flush_q and the entirety of
bna_rit_mod_uninit() is unused since variables are purely set but no
action is made using them.

Same for 'bna' in bna_rit_create() and 'ret' in bna_rx_create().

Just kill them off.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During a kernel crash, bna control path state machine and firmware do not
get a notification and hence are not cleanly shutdown. The registers
holding driver/IOC state information are not reset back to valid
disabled/parking values. This causes subsequent driver initialization
to hang during kdump kernel boot. This patch, during the initialization
of first PCI function, resets corresponding register when unclean shutown
is detect by reading chip registers. This will make sure that ioc/fw
gets clean re-initialization.
Signed-off-by: NDebashis Dutt <ddutt@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch contains a fix for gracefully handling firmware heartbeat
failure instead of forcing panic.
Signed-off-by: NDebashis Dutt <ddutt@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change Details:
	- Made IOC auto_recovery synchronized and not timer based.
	- Only one PCI function will attempt to recover and reinitialize
	the ASIC on a failure, that too after all the active PCI
	functions acknowledge the IOC failure.
Signed-off-by: NDebashis Dutt <ddutt@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change Details:
	- Added a check in ioc firmware lock function to see if IOC is
	in BFI_IOC_UNINIT state or not. If it is not in UNINIT state
	and the last IOC boot was not done by OS driver, force IOC state
	to BFI_IOC_UNINIT
	- Unused macro and API cleanup
Signed-off-by: NDebashis Dutt <ddutt@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As suggested by Stephen Hemminger:
1) Made functions and data structures static wherever possible.
2) Removed unused code.
Signed-off-by: NDebashis Dutt <ddutt@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mod->mbhdlr[] array has BFI_MC_MAX elements.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is the patch to fix the build break caused by multiple
definitions of symbols between Brocade's FC/FCOE driver(BFA)
and 10G Networking Driver(BNA).

Changes are:

1. locally used functions are made static 

2. unused functions are removed

3. using unique namespaces for the function names that must be
globally visible
Signed-off-by: NDebashis Dutt <ddutt@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is patch 1/6 which contains linux driver source for
Brocade's BR1010/BR1020 10Gb CEE capable ethernet adapter.
Signed-off-by: NDebashis Dutt <ddutt@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>