Use h2c to tell the firmware if the number of AP is more than 10 or
not.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Here we monitor one more wifi rssi to check the status of the network
and set the coex table instead of the legacy way.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

For p2p/miracast, the wifi may have multiple ports for different roles.
Under this, we need extra settings for turning off the tdma and proper
coex table parameters.

We monnitor the number of links on a port to determine if it is for
p2p/miracast or not.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Monitor the rssi state to set the tdma and limit rx aggregation size to
fit the bt profiling.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Fix some ident and naming for linux coding style.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

For bt a2dp, we need to check more rssi state combinations to have
better voice quality.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Let the wifi use main antenna to have higher power.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The threshold is used to adjust the base line for the rssi state.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Use software dac swing and double check if it is sco_only to set the
tdma for voice quality.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

1. Add more cases to adjust the wifi duration and add a case with
the max interval of 3 for some future uses.

2. rename tdma_adj -> ps_tdma_du_adj to indicate that this member is
for power saving tdma duration adjustment
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The dac swing level should be an unsigned 32-bit value rather than
boolean.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Depending on the state of wifi, we need to set different tdma and coex
table parameters to make wfi and bt coexist smoothly. Otherwise the
bt may have low sound quality or mouse lag, which mean bad user
experience. The same problem may occur on wifi also, if could disconnect
or lose some important packets.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

If the wifi or bt has low rssi, they need extra parameter settings for
the tdma.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Tune the wifi/bt slot time to get better performance.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Register 0xcb4 determines if the PTA circuit can control the swtich
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Instead of just setting the coex table directly, we check if the
wifi is under some important activity (scanning|roaming|linking) and
mark the packets as high priority in that case.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When wifi is at 5G band, it does not intefere with 2.4G bt signal,
hence we can just ignore it and transmit normally as nothing happened.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Monitor wifi status and check if it is changed.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Gather multiple coex table settings into a function coex_table_with_type()
and control the coex table according the type value as put in
switch-case expression.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Remove workaround for HT40 issues for RF low pass filter.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The power_save_state function checks the state of power saving.
For tdma settings, the wifi sends nullfunc to pretend enter power saving
and then bt can transmit. Hence the coex needs to check the power status
before set the pstdma function.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Change h2c parameter to decrease tx penalty.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Gather variables to the 8821a2ant coex structure.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Originally we only increase/decrease bt power in a fixed power gap, this
patch makes us be able to modify bt power for multiple power gaps and we
can precisely adjust the bt power.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This function updates the information of bt profiling to help us decide
the network status and dispatch the resource properly.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

If there are a lot of low-rate packets, then the connection of wifi is
unstable. If so, we should switch resource to bt to have a higher
transmission quality, or wifi resource will be wasted
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

We monitor the packet counter to guess if the bt is slave or not, and
when bt is slave, it may receive packet at any time, so we will have to
take care about it
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Larger packets have higher opportunity to be interrupt by bt signal.
In order to shorten the transmission time, control the packet
aggregation size.
Signed-off-by: NYan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

His email is bouncing, and he'd like to use this new one.

Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Nishant Sarmukadam <nishants@marvell.com>
Cc: Ganapathi Bhat <gbhat@marvell.com>
Cc: Xinming Hu <huxm@marvell.com>
Signed-off-by: NBrian Norris <briannorris@chromium.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

'chan_stats' is (re)allocated in _mwifiex_fw_dpc() ->
mwifiex_init_channel_scan_gap(), which is called whenever the device is
initialized -- at probe or at reset.

But we only free it in we completely unregister the adapter, meaning we
leak a copy of it during every reset.

Let's free it in the shutdown / removal paths instead (and in the
error-handling path), to avoid the leak.

Ideally, we can eventually unify much of mwifiex_shutdown_sw() and
mwifiex_remove_card() (way too much copy-and-paste) to reduce the burden
on bugfixes like this. But that's work for tomorrow.
Signed-off-by: NBrian Norris <briannorris@chromium.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When we shut down the device (i.e., during 'reset'), we cancel any
outstanding work, but we don't clear any work-related flags. This can
cause problems if, e.g., we begin to queue a new firmware dump or card
reset while the other one is in progress. That might leave work_flags
with a stale value, and we might begin one of these *after* we've
completely reset the device. That doesn't make sense, because all
firmware context will have been lost by then.

This fixes some forms of cascading failures, where I:

(a) force a firmware dump (cat /sys/kernel/debug/mwifiex/mlan0/device_dump)
(b) run a Wifi scan in parallel (iw mlan0 scan)
(c) the scan times out due to (a) hogging the interface
(d) the command timeout triggers another firmware dump and a reset [*]
(e) the 2nd firmware dump flag persists across the reset
(f) as soon as the interface comes back up, we trigger the pending
    firmware dump
(g) subsequent commands time out again, while we are processing the
    firmware dump; return to (d)

[*] Note that automatic card_reset() support is not yet implemented for
the mwifiex PCIe driver, so we won't hit *exactly* this behavior yet.
But we can see similarly-confusing behaviors today.
Signed-off-by: NBrian Norris <briannorris@chromium.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

If we reset because of a command timeout, we should reset this flag.
Otherwise, we might erroneously think the next command after reset is
timing out, and trigger another reset.

The above behavior effectively neuters the automatic card_reset()
behavior, as it means we will never recover from a command timeout
properly (and in fact, we might enter an infinite loop:

  timeout -> reset -> (fake) timeout -> reset -> ...

This fixes a bug introduced with introduction of PCIe function level
reset support, but it was carried into the SDIO driver when it was
converted to use the same codepaths. And this is currently mostly a
problem only in the SDIO driver, because it's the only one with
automatic card_reset() support (e.g., on command timeout). But it will
be a problem for PCIe too, as I'm working on supporting automatic
card_reset() for PCIe.

Fixes: c742e623 ("mwifiex: sdio card reset enhancement")
Fixes: 4c5dae59 ("mwifiex: add PCIe function level reset support")
Signed-off-by: NBrian Norris <briannorris@chromium.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Command buffers (skb's) are allocated by the main driver, and freed upon
the last use. That last use is often in mwifiex_free_cmd_buffer(). In
the meantime, if the command buffer gets used by the PCI driver, we map
it as DMA-able, and store the mapping information in the 'cb' memory.

However, if a command was in-flight when resetting the device (and
therefore was still mapped), we don't get a chance to unmap this memory
until after the core has cleaned up its command handling.

Let's keep a refcount within the PCI driver, so we ensure the memory
only gets freed after we've finished unmapping it.

Noticed by KASAN when forcing a reset via:

  echo 1 > /sys/bus/pci/.../reset

The same code path can presumably be exercised in remove() and
shutdown().

[  205.390377] mwifiex_pcie 0000:01:00.0: info: shutdown mwifiex...
[  205.400393] ==================================================================
[  205.407719] BUG: KASAN: use-after-free in mwifiex_unmap_pci_memory.isra.14+0x4c/0x100 [mwifiex_pcie] at addr ffffffc0ad471b28
[  205.419040] Read of size 16 by task bash/1913
[  205.423421] =============================================================================
[  205.431625] BUG skbuff_head_cache (Tainted: G    B          ): kasan: bad access detected
[  205.439815] -----------------------------------------------------------------------------
[  205.439815]
[  205.449534] INFO: Allocated in __build_skb+0x48/0x114 age=1311 cpu=4 pid=1913
[  205.456709] 	alloc_debug_processing+0x124/0x178
[  205.461282] 	___slab_alloc.constprop.58+0x528/0x608
[  205.466196] 	__slab_alloc.isra.54.constprop.57+0x44/0x54
[  205.471542] 	kmem_cache_alloc+0xcc/0x278
[  205.475497] 	__build_skb+0x48/0x114
[  205.479019] 	__netdev_alloc_skb+0xe0/0x170
[  205.483244] 	mwifiex_alloc_cmd_buffer+0x68/0xdc [mwifiex]
[  205.488759] 	mwifiex_init_fw+0x40/0x6cc [mwifiex]
[  205.493584] 	_mwifiex_fw_dpc+0x158/0x520 [mwifiex]
[  205.498491] 	mwifiex_reinit_sw+0x2c4/0x398 [mwifiex]
[  205.503510] 	mwifiex_pcie_reset_notify+0x114/0x15c [mwifiex_pcie]
[  205.509643] 	pci_reset_notify+0x5c/0x6c
[  205.513519] 	pci_reset_function+0x6c/0x7c
[  205.517567] 	reset_store+0x68/0x98
[  205.521003] 	dev_attr_store+0x54/0x60
[  205.524705] 	sysfs_kf_write+0x9c/0xb0
[  205.528413] INFO: Freed in __kfree_skb+0xb0/0xbc age=131 cpu=4 pid=1913
[  205.535064] 	free_debug_processing+0x264/0x370
[  205.539550] 	__slab_free+0x84/0x40c
[  205.543075] 	kmem_cache_free+0x1c8/0x2a0
[  205.547030] 	__kfree_skb+0xb0/0xbc
[  205.550465] 	consume_skb+0x164/0x178
[  205.554079] 	__dev_kfree_skb_any+0x58/0x64
[  205.558304] 	mwifiex_free_cmd_buffer+0xa0/0x158 [mwifiex]
[  205.563817] 	mwifiex_shutdown_drv+0x578/0x5c4 [mwifiex]
[  205.569164] 	mwifiex_shutdown_sw+0x178/0x310 [mwifiex]
[  205.574353] 	mwifiex_pcie_reset_notify+0xd4/0x15c [mwifiex_pcie]
[  205.580398] 	pci_reset_notify+0x5c/0x6c
[  205.584274] 	pci_dev_save_and_disable+0x24/0x6c
[  205.588837] 	pci_reset_function+0x30/0x7c
[  205.592885] 	reset_store+0x68/0x98
[  205.596324] 	dev_attr_store+0x54/0x60
[  205.600017] 	sysfs_kf_write+0x9c/0xb0
...
[  205.800488] Call trace:
[  205.802980] [<ffffffc00020a69c>] dump_backtrace+0x0/0x190
[  205.808415] [<ffffffc00020a96c>] show_stack+0x20/0x28
[  205.813506] [<ffffffc0005d020c>] dump_stack+0xa4/0xcc
[  205.818598] [<ffffffc0003be44c>] print_trailer+0x158/0x168
[  205.824120] [<ffffffc0003be5f0>] object_err+0x4c/0x5c
[  205.829210] [<ffffffc0003c45bc>] kasan_report+0x334/0x500
[  205.834641] [<ffffffc0003c3994>] check_memory_region+0x20/0x14c
[  205.840593] [<ffffffc0003c3b14>] __asan_loadN+0x14/0x1c
[  205.845879] [<ffffffbffc46171c>] mwifiex_unmap_pci_memory.isra.14+0x4c/0x100 [mwifiex_pcie]
[  205.854282] [<ffffffbffc461864>] mwifiex_pcie_delete_cmdrsp_buf+0x94/0xa8 [mwifiex_pcie]
[  205.862421] [<ffffffbffc462028>] mwifiex_pcie_free_buffers+0x11c/0x158 [mwifiex_pcie]
[  205.870302] [<ffffffbffc4620d4>] mwifiex_pcie_down_dev+0x70/0x80 [mwifiex_pcie]
[  205.877736] [<ffffffbffc1397a8>] mwifiex_shutdown_sw+0x190/0x310 [mwifiex]
[  205.884658] [<ffffffbffc4606b4>] mwifiex_pcie_reset_notify+0xd4/0x15c [mwifiex_pcie]
[  205.892446] [<ffffffc000635f54>] pci_reset_notify+0x5c/0x6c
[  205.898048] [<ffffffc00063a044>] pci_dev_save_and_disable+0x24/0x6c
[  205.904350] [<ffffffc00063cf0c>] pci_reset_function+0x30/0x7c
[  205.910134] [<ffffffc000641118>] reset_store+0x68/0x98
[  205.915312] [<ffffffc000771588>] dev_attr_store+0x54/0x60
[  205.920750] [<ffffffc00046f53c>] sysfs_kf_write+0x9c/0xb0
[  205.926182] [<ffffffc00046dfb0>] kernfs_fop_write+0x184/0x1f8
[  205.931963] [<ffffffc0003d64f4>] __vfs_write+0x6c/0x17c
[  205.937221] [<ffffffc0003d7164>] vfs_write+0xf0/0x1c4
[  205.942310] [<ffffffc0003d7da0>] SyS_write+0x78/0xd8
[  205.947312] [<ffffffc000204634>] el0_svc_naked+0x24/0x28
...
[  205.998268] ==================================================================

This bug has been around in different forms for a while. It was sort of
noticed in commit 955ab095 ("mwifiex: Do not kfree cmd buf while
unregistering PCIe"), but it just fixed the double-free, without
acknowledging the potential for use-after-free.

Fixes: fc331460 ("mwifiex: use pci_alloc/free_consistent APIs for PCIe")
Cc: <stable@vger.kernel.org>
Signed-off-by: NBrian Norris <briannorris@chromium.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

A separate wifi-only firmware was download during pcie function level
reset. It is in fact the tail part of wifi/bt combo firmware. Per
Brian's and Dmitry's suggestion, this patch extract the wifi part from
combo firmware.

After that, the mrvl/pcie8997_wlan_v4.bin image in linux-firmware repo
is redundant (though I guess we keep it around to support older
kernels).
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NGanapathi Bhat <gbhat@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NBrian Norris <briannorris@chromium.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch correct pcie scratch register name, to keep the same with
chipset side definition.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

mwifiex_dbg will do nothing before adapter->dev get assigned. several logs
lost in this case. it can be avoided by fall back to pr_info.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Reviewed-by: NBrian Norris <briannorris@chromium.org>
Reviewed-by: NDmitry Torokhov <dtor@chromium.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

If wakeup interrupt handler is called, we know that the wakeup
interrupt number is valid, there is no need to check it.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Reviewed-by: NDmitry Torokhov <dtor@chromium.org>
Reviewed-by: NBrian Norris <briannorris@chromium.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

nl80211 provides the NL80211_SCAN_FLAG_RANDOM_ADDR for every scan
request that should be randomized; the absence of such a flag means we
should not randomize. However, mwifiex was stashing the latest
randomization request and *always* using it for future scans, even those
that didn't set the flag.

Let's zero out the randomization info whenever we get a scan request
without NL80211_SCAN_FLAG_RANDOM_ADDR. I'd prefer to remove
priv->random_mac entirely (and plumb the randomization MAC properly
through the call sequence), but the spaghetti is a little difficult to
unravel here for me.

Fixes: c2a8f0ff ("mwifiex: support random MAC address for scanning")
Cc: <stable@vger.kernel.org> # 4.9+
Signed-off-by: NBrian Norris <briannorris@chromium.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The fwsignal module is only referenced by the bcdc module and part of the
bcdc protocol. So only build it when CONFIG_BRCMFMAC_PROTO_BCDC is selected.

Fixes: acf8ac41 ("brcmfmac: remove reference to fwsignal data from struct brcmf_pub")
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Merge tag 'iwlwifi-next-for-kalle-2017-04-13' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next

Patches intended for v4.12:

  * Some small fixes here and there;
  * The usual cleanups and small improvements;
  * Work to support A000 devices continues;
  * New FW API version;
  * Some debugging improvements;