- 17 5月, 2012 36 次提交
-
-
由 Avinash Patil 提交于
1. Support for parsing security related parameters from cfg80211_ap_settings in start_ap cfg80211 handler 2. Conversion of these security information into FW understandle TLVs and setting into FW thru sys_config command 3. key management is done on host. This ensures that FW forwards EAPOL key packets to host instead of processing on its own. Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NKiran Divekar <dkiran@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Avinash Patil 提交于
Added logic to handle AP event that are generated by the firmware. As MLME/SME is implemented in the firmware, events such as station association and deauthentication, must be sent to userspace (hostapd) for creating and deleting station database. Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NYogesh Powar <yogeshp@marvell.com> Signed-off-by: NKiran Divekar <dkiran@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Avinash Patil 提交于
1. add start AP and stop AP handlers 2. support for parsing ssid, beacon period, DTIM period from beacon_parameters structure and setting it to FW. Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: NKiran Divekar <dkiran@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Avinash Patil 提交于
Add support for setting fragmentation threshold, RTS threshold and retry limit. Since wiphy parameters are properties of physical device, appropriate function to set phy parameters is invoked depending upon bss_type(STA or AP) for each virtual interface. Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: NKiran Divekar <dkiran@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Avinash Patil 提交于
mlan0: managed or ibss The iftype can be changed from STATION to ADHOC, and vice versa. uap0: AP only The iftype cannot be changed. Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: NKiran Divekar <dkiran@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Avinash Patil 提交于
While in AP mode, we should stop BSS in deauthentication handler. Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: NKiran Divekar <dkiran@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Avinash Patil 提交于
1. support for AP sys_config command and added parsing of channel information. 2. support for setting AP channel from cfg80211 set_channel handler Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: NKiran Divekar <dkiran@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Avinash Patil 提交于
1. separate file for preparing uAP command buffer 2. definition of bss_start and bss_stop commands being sent to firmware Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: NKiran Divekar <dkiran@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Avinash Patil 提交于
Modify key related cfg80211 handlers to copy peer mac address for pairwise keys. If peer mac address is not present or group keys, it will be sent as broadcast mac address. This would be required since hostapd downloads per peer PTK. Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: NKiran Divekar <dkiran@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Avinash Patil 提交于
Since wiphy structure is per adapter we would save adapter, instead of mwifiex private pointer, in wiphy_priv. Also move country_info from mwifiex_private to mwifiex_adapter as making it part of mwifiex_adapter looks logical. Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: NKiran Divekar <dkiran@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Avinash Patil 提交于
mwifiex supports STA and AP interfaces which use same phy. Indicate this to cfg80211. Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Avinash Patil 提交于
1. wiphy structure is per device; hence moved it to mwifiex_adapter mwifiex_register_cfg80211 takes mwifiex_adapter as parameter. This function only registers wiphy with cfg80211. 2. Creation of interfaces is moved to cfg80211 add_virtual_interface handler. 3. Create 2 interfaces by default: station and AP Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NKiran Divekar <dkiran@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Avinash Patil 提交于
Commands like IBSS coalescing status, power save, 11D should be handled only when bss_type is STA. Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: NKiran Divekar <dkiran@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Avinash Patil 提交于
Reserve space for one more priv structure. This will be used by AP interface. Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: NKiran Divekar <dkiran@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Bjorn Helgaas 提交于
Use pci_is_pcie() instead of looking at obsolete is_pcie field in struct pci_dev. CC: Stefano Brivio <stefano.brivio@polimi.it> CC: b43-dev@lists.infradead.org CC: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: NBjorn Helgaas <bhelgaas@google.com> Reviewed-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Hauke Mehrtens 提交于
This is based on code from the Broadcom SDK. Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de> Tested-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Hauke Mehrtens 提交于
If brcmsmac is used on non PCI(s) devices it should not try to access bus->host_pci. Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de> Tested-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Hauke Mehrtens 提交于
The irq number is copied from the PCIe host device to the bcma cores so just request it using the bcma core device. Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de> Tested-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Hauke Mehrtens 提交于
There is no code doing anything useful in nicpci.c anymore, so remove it. Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de> Tested-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Hauke Mehrtens 提交于
This is now done in bcma by bcma_core_pci_fixcfg(). Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de> Tested-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Hauke Mehrtens 提交于
This is now done by calling bcma_core_pci_extend_L1time() Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de> Tested-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Hauke Mehrtens 提交于
This function is now unreferenced Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de> Tested-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Hauke Mehrtens 提交于
This is already done by bcma in bcma_pcicore_serdes_workaround(). Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de> Tested-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Hauke Mehrtens 提交于
This is now done by calling bcma_core_set_clockmode() Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de> Tested-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Hauke Mehrtens 提交于
This is now done by calling bcma_chipco_gpio_control(). Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de> Tested-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Hauke Mehrtens 提交于
ai_chipcontrl_epa4331 is not referenced by any method in brcmsmac and the functionality is already in bcma_chipco_bcm4331_ext_pa_lines_ctl in drivers/bcma/driver_chipcommon_pmu.c Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de> Tested-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Hauke Mehrtens 提交于
This is now done by calling bcma_core_pci_irq_ctl() Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de> Tested-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Hauke Mehrtens 提交于
This is now done by bcma_core_pci_config_fixup() in drivers/bcma/driver_pci.c Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de> Tested-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Hauke Mehrtens 提交于
The devices I know of are not using a PCIe core with rev <= 10. The BCM4718 uses a PCIe core with revision 14 and the BCM43224 uses a PCIe core with revision 15. This patch removes support for old PCIe core versions, which are not found on devices supported by brcmsmac. Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de> Tested-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Hauke Mehrtens 提交于
There are no devices which are using bcma and have a PCI bus, just a PCIe bus or something else. bcma does not support PCI devices, so lets also remove PCI support from brcmsmac. All devices currently supported by brcmsmac are PCIe based. Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de> Tested-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Hauke Mehrtens 提交于
The lowest chip common version used on bcma based devices is 31 on the bcm4718 and 32 on the bcm4313, bcm43224, and bcm43225, so the support for the old versions could be removed. Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de> Tested-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Hauke Mehrtens 提交于
bcma now provide this data and brcmsmac should get it from there and not parse it by its self. Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de> Tested-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Hauke Mehrtens 提交于
brcmsmac now takes the sprom from bcma and do not uses its own sprom parsing any more. Remove this code as it is not used any more. Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de> Tested-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Hauke Mehrtens 提交于
bcma now provides all sprom attributes needed by brcmsmac and also parses them from the pci sprom ant otp. Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de> Tested-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Hauke Mehrtens 提交于
This struct contains information about the board, the chip is running on. The struct is filled for PCIe devices and SoCs. This information is used by b43 and will be used by brcmsmac soon. Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de> Tested-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Hauke Mehrtens 提交于
Previously the rev contained the revision read from the pci config space and was used as board_rev in the wireless drivers. This is wrong the board_rev is only fetched from the sprom accordingly to the open source part of the Broadcom SDK and brcmsmac. This patch removes the rev from the boardinfo structure and uses the board_rev attribute from sprom instead. This attribute is filled by PCI, PCMCIA, SDIO and SoC code. Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de> Tested-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 16 5月, 2012 4 次提交
-
-
Make use of REGAINED_BSS_EVENT and instead of reporting connection loss immediately on each BEACON_LOSE event, try if not regained in reasonable period of time. Signed-off-by: Nbartosz.markowski <bartosz.markowski@tieto.com> Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Jesper Juhl 提交于
We currently do this: int wl1271_cmd_build_arp_rsp(struct wl1271 *wl, struct wl12xx_vif *wlvif) ... struct wl12xx_arp_rsp_template *tmpl; struct ieee80211_hdr_3addr *hdr; ... tmpl = (struct wl12xx_arp_rsp_template *)skb_put(skb, sizeof(*tmpl)); memset(tmpl, 0, sizeof(tmpl)); ... hdr = (struct ieee80211_hdr_3addr *)skb_push(skb, sizeof(*hdr)); memset(hdr, 0, sizeof(hdr)); ... I believe we want to set the entire structures to 0 with those memset() calls, not just zero the initial part of them (size of the pointer bytes). Signed-off-by: NJesper Juhl <jj@chaosbits.net> Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Randy Dunlap 提交于
wl12xx build fails with many undefined symbol errors when MAC80211 and CFG80211 are not enabled, so make WLCORE and WL12XX depend on MAC80211 (which already depends on CFG80211). Here are a few of the many build errors: drivers/built-in.o: In function `wl1271_register_hw': main.c:(.text+0x4197cd): undefined reference to `ieee80211_register_hw' drivers/built-in.o: In function `wl1271_rx_streaming_timer': main.c:(.text+0x419818): undefined reference to `ieee80211_queue_work' drivers/built-in.o: In function `wl1271_flush_deferred_work': main.c:(.text+0x419910): undefined reference to `ieee80211_rx' main.c:(.text+0x419938): undefined reference to `ieee80211_tx_status' drivers/built-in.o: In function `wl12xx_op_channel_switch': main.c:(.text+0x419afc): undefined reference to `ieee80211_chswitch_done' drivers/built-in.o: In function `wl1271_ssid_set': drivers/built-in.o: In function `wl1271_event_process': event.c:(.text+0x41fec4): undefined reference to `ieee80211_sched_scan_stopped' event.c:(.text+0x41ff88): undefined reference to `ieee80211_cqm_rssi_notify' event.c:(.text+0x42000d): undefined reference to `ieee80211_stop_rx_ba_session' event.c:(.text+0x420048): undefined reference to `ieee80211_stop_rx_ba_session' event.c:(.text+0x4200b8): undefined reference to `ieee80211_chswitch_done' event.c:(.text+0x4201ae): undefined reference to `ieee80211_find_sta' event.c:(.text+0x4201ba): undefined reference to `ieee80211_report_low_ack' event.c:(.text+0x42021b): undefined reference to `ieee80211_connection_loss' drivers/built-in.o: In function `wl1271_tx_complete_packet': tx.c:(.text+0x4206a6): undefined reference to `ieee80211_get_hdrlen_from_skb' drivers/built-in.o: In function `wl1271_tx_fill_hdr': tx.c:(.text+0x4208ca): undefined reference to `ieee80211_hdrlen' drivers/built-in.o: In function `wl1271_handle_tx_low_watermark': (.text+0x420e25): undefined reference to `ieee80211_wake_queue' drivers/built-in.o: In function `wl12xx_rearm_rx_streaming': (.text+0x420ed9): undefined reference to `ieee80211_queue_work' drivers/built-in.o: In function `wl1271_tx_work_locked': (.text+0x421008): undefined reference to `ieee80211_free_txskb' drivers/built-in.o: In function `wl1271_rx_status.clone.2': rx.c:(.text+0x421593): undefined reference to `ieee80211_channel_to_frequency' drivers/built-in.o: In function `wl1271_ps_filter_frames': ps.c:(.text+0x421a41): undefined reference to `ieee80211_tx_status' Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net> Cc: Luciano Coelho <coelho@ti.com> Cc: linux-wireless@vger.kernel.org Cc: "John W. Linville" <linville@tuxdriver.com> Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Dan Carpenter 提交于
GFP_DMA isn't supposed to be used by itself. This allocation is allowed to sleep so it should be ORing it with GFP_KERNEL. Also we should check for allocations errors. Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com> Signed-off-by: NLuciano Coelho <coelho@ti.com>
-