The CFA-10056 is a breakout board for the CFA-10036, and is
basically a CFA-10037, with a 4.3" screen.
Signed-off-by: NBrian Lilly <brian@crystalfontz.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Written by Catalin Marinas, tested by APM on storm platform. This is needed
because of the failures encountered when running SpecWeb benchmark test.
Signed-off-by: NFeng Kan <fkan@apm.com>
Acked-by: NKumar Sankaran <ksankaran@apm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Avoids the following warning when SMP is off:

warning: (ARCH_KEYSTONE && SOC_OMAP5) selects ARM_ERRATA_798181 which
has unmet direct dependencies (CPU_V7 && SMP)
Reported-by: NEmilio López <emilio@elopez.com.ar>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

With the recent cleanup in Exynos platform code notably commits
17859bec ("ARM: EXYNOS: Do not select legacy Kconfig symbols any
more") and b9222210 ("ARM: EXYNOS: Remove mach/gpio.h"), the definition
of ARCH_NR_GPIOS got removed. This started causing problems on SoCs like
Exynos4412 which have more than the default number of GPIOs. Thus define
this number in KConfig file which takes care of current SoC requirements
and provides scope for GPIO expanders. Without this patch we get the
following errors during boot:

gpiochip_add: gpios 251..258 (gpv0) failed to register
samsung-pinctrl 106e0000.pinctrl: failed to register gpio_chip gpv0, error code: -22
samsung-pinctrl: probe of 106e0000.pinctrl failed with error -22
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Cc: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Presently, using exynos_defconfig with CONFIG_DEBUG_LL and CONFIG_EARLY_PRIN
on, kernel is not booting, we are getting following:

[    0.000000] ------------[ cut here ]------------
[    0.000000] kernel BUG at mm/vmalloc.c:1134!
[    0.000000] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
[    0.000000] Modules linked in:
[    0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 3.11.0-rc1 #633
[    0.000000] task: c052ec48 ti: c0524000 task.ti: c0524000
[    0.000000] PC is at vm_area_add_early+0x54/0x94
[    0.000000] LR is at add_static_vm_early+0xc/0x60

Its because exynos[4/5]_map_io() function ioremaps a single 512KB memory
size for all the four uart ports which envelopes the mapping created by
debug_ll_io_init(), called earlier in exynos_init_io().

This patch removes iodesc entries for UART controller for all Samsung SoC's,
since now the Samsung uart driver does a ioremap during probe and any needed
iomapping for earlyprintk will be handled by debug_ll_io_init().

Tested on smdk4412 and smdk5250.
Signed-off-by: NYadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Basically this code gets executed only during debugging i.e when
DEBUG_LL & SAMSUNG_PM_DEBUG is on, so required only for UART used
for debugging. Since we are removing static iodesc entries for UARTs,
so now only the selected (CONFIG_DEBUG_S3C_UART) UART will be
ioremapped by the debug_ll_io_init() for DEBUG_LL, so save/restore
uart registers only for selected uart.
Signed-off-by: NYadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This reverts commits
    67822649
    39761214
    0b95a7f8
    31d93962
    2d31e518

Unfortunately this change broke boot on some systems that used an
initrd which does not include the newly created crct10dif modules.
As these modules are required by sd_mod under certain configurations
this is a serious problem.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

This patch enables the selection of samsung pm related stuffs
when SAMSUNG_PM config is enabled and not just when generic PM
config is enabled. Power management for s3c64XX and s3c24XX
is enabled by default and for other platform depends on S5P_PM.
This patch also fixes the following compilation error's when compiling
a platform like exynos5440 which does not select pm stuffs.

arch/arm/mach-exynos/built-in.o: In function '__virt_to_phys':
linux/arch/arm/include/asm/memory.h:175: undefined reference to 's3c_cpu_resume'
linux/arch/arm/include/asm/memory.h:175: undefined reference to 's3c_cpu_resume'
linux/arch/arm/include/asm/memory.h:175: undefined reference to 's3c_cpu_resume'
linux/arch/arm/include/asm/memory.h:175: undefined reference to 's3c_cpu_resume'
arch/arm/mach-exynos/built-in.o: In function 'exynos5_init_irq':
linux/arch/arm/mach-exynos/common.c:492: undefined reference to 's3c_irq_wake'
linux/arch/arm/mach-exynos/common.c:492: undefined reference to 's3c_irq_wake'
arch/arm/mach-exynos/built-in.o: In function 'exynos4_init_irq':
linux/arch/arm/mach-exynos/common.c:476: undefined reference to 's3c_irq_wake'
linux/arch/arm/mach-exynos/common.c:476: undefined reference to 's3c_irq_wake'
arch/arm/plat-samsung/built-in.o: In function 's3c_irqext_wake':
linux/arch/arm/plat-samsung/pm.c:144: undefined reference to 's3c_irqwake_eintallow'
linux/arch/arm/plat-samsung/pm.c:144: undefined reference to 's3c_irqwake_eintallow'
arch/arm/plat-samsung/built-in.o: In function 's3c_pm_enter':
linux/arch/arm/plat-samsung/pm.c:263: undefined reference to 's3c_irqwake_intallow'
linux/arch/arm/plat-samsung/pm.c:263: undefined reference to 's3c_irqwake_intallow'
linux/arch/arm/plat-samsung/pm.c:264: undefined reference to 's3c_irqwake_eintallow'
linux/arch/arm/plat-samsung/pm.c:264: undefined reference to 's3c_irqwake_eintallow'
linux/arch/arm/plat-samsung/pm.c:275: undefined reference to 's3c_pm_save_core'
linux/arch/arm/plat-samsung/pm.c:279: undefined reference to 's3c_pm_configure_extint'
linux/arch/arm/plat-samsung/pm.c:310: undefined reference to 's3c_pm_restore_core'
make: *** [vmlinux] Error 1
Signed-off-by: NAmit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

When the task moves around the system, the corresponding cpuhw
per cpu strcuture should be popullated with the BHRB filter
request value so that PMU could be configured appropriately with
that during the next call into power_pmu_enable().
Signed-off-by: NAnshuman Khandual <khandual@linux.vnet.ibm.com>
Acked-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Completely ignore BHRB privilege state filter request as we are
already configuring that with privilege state filtering attribute
for the accompanying PMU event. This would help achieve cleaner
user space interaction for BHRB.

This patch fixes a situation like this

Before patch:-
------------
./perf record -j any -e branch-misses:k ls
Error:
The sys_perf_event_open() syscall returned with 95 (Operation not
supported) for event (branch-misses:k).
/bin/dmesg may provide additional information.
No CONFIG_PERF_EVENTS=y kernel support configured?

Here 'perf record' actually copies over ':k' filter request into BHRB
privilege state filter config and our previous check in kernel would
fail that.

After patch:-
-------------
./perf record -j any -e branch-misses:k ls
perf  perf.data  perf.data.old  test-mmap-ring
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.002 MB perf.data (~102 samples)]
Signed-off-by: NAnshuman Khandual <khandual@linux.vnet.ibm.com>
Acked-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Mark pnv_pci_init_ioda2_phb() as __init.  It is called only from an
init function (pnv_pci_init()), and it calls an init function
(pnv_pci_init_ioda_phb()):

    pnv_pci_init                # init
      pnv_pci_init_ioda2_phb    # non-init
	pnv_pci_init_ioda_phb   # init

This should fix a section mismatch warning.
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The sllp value is stored in mmu_psize_defs in such a way that we can easily OR
the value to get the operand for slbmte instruction. ie, the L and LP bits are
not contiguous. Decode the bits and use them correctly in tlbie.
regression is introduced by 1f6aaacc
"powerpc: Update tlbie/tlbiel as per ISA doc"
Reported-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We should not fallthrough different case statements in hpte_decode. Add
break statement to break out of the switch. The regression is introduced by
dcda287a "powerpc/mm: Simplify hpte_decode"
Reported-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Commit 801eb73f introduced
a bug while checking PTE flags. We have to drop the _PAGE_COHERENT flag
when __PAGE_NO_CACHE is set and the cache update policy is not write-through
(i.e. _PAGE_WRITETHRU is not set)
Signed-off-by: NDenis Kirjanov <kda@linux-powerpc.org>
Reviewed-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
CC:  Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This patch restores serial port operation which has been broken since
commit 60e93575 ("serial: samsung: enable clock before clearing
pending interrupts during init")

That commit only uncovered the real issue which was missing clkdev
entries for the "uart" clocks on S3C2440. It went unnoticed so far
because return value of clk API calls were not being checked at all
in the samsung serial port driver.

This patch should be backported to at least 3.10 stable kernel, since
the serial port has not been working on s3c2440 since 3.10-rc5.

Cc: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: NSylwester Nawrocki <sylvester.nawrocki@gmail.com>
[on S3C2440 SoC based Mini2440 board]
Tested-by: NSylwester Nawrocki <sylvester.nawrocki@gmail.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Tested-by: NJuergen Beisert <jbe@pengutronix.de>
Cc: <stable@vger.kernel.org>	[3.10]
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The patch introduces flag EEH_DEV_SYSFS to keep track that the sysfs
entries for the corresponding EEH device (then PCI device) has been
added or removed, in order to avoid race condition.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The patch fixes following issue:

Unbalanced enable for IRQ 23
------------[ cut here ]------------
WARNING: at kernel/irq/manage.c:437
:
NIP [c00000000016de8c] .__enable_irq+0x11c/0x140
LR [c00000000016de88] .__enable_irq+0x118/0x140
Call Trace:
[c000003ea1f23880] [c00000000016de88] .__enable_irq+0x118/0x140 (unreliable)
[c000003ea1f23910] [c00000000016df08] .enable_irq+0x58/0xa0
[c000003ea1f239a0] [c0000000000388b4] .eeh_enable_irq+0xc4/0xe0
[c000003ea1f23a30] [c000000000038a28] .eeh_report_reset+0x78/0x130
[c000003ea1f23ac0] [c000000000037508] .eeh_pe_dev_traverse+0x98/0x170
[c000003ea1f23b60] [c0000000000391ac] .eeh_handle_normal_event+0x2fc/0x3d0
[c000003ea1f23bf0] [c000000000039538] .eeh_handle_event+0x2b8/0x2c0
[c000003ea1f23c90] [c000000000039600] .eeh_event_handler+0xc0/0x170
[c000003ea1f23d30] [c0000000000da9a0] .kthread+0xf0/0x100
[c000003ea1f23e30] [c00000000000a1dc] .ret_from_kernel_thread+0x5c/0x80
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

While restoring BARs for one specific PCI device, the pci_dev
instance should have been released. So it's not reliable to use
the pci_dev instance on restoring BARs. However, we still need
some information (e.g. PCIe capability position, header type) from
the pci_dev instance. So we have to store those information to
EEH device in advance.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

When EEH error happens to one specific PE, some devices with drivers
supporting EEH won't except hotplug on the device. However, there
might have other deivces without driver, or with driver without EEH
support. For the case, we need do partial hotplug in order to make
sure that the PE becomes absolutely quite during reset. Otherise,
the PE reset might fail and leads to failure of error recovery.

The current code doesn't handle that 'mixed' case properly, it either
uses the error callbacks to the drivers, or tries hotplug, but doesn't
handle a PE (EEH domain) composed of a combination of the two.

The patch intends to support so-called "partial" hotplug for EEH:
Before we do reset, we stop and remove those PCI devices without
EEH sensitive driver. The corresponding EEH devices are not detached
from its PE, but with special flag. After the reset is done, those
EEH devices with the special flag will be scanned one by one.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

When EEH error happens to one specific PE, the device drivers
of its attached EEH devices (PCI devices) are checked to see
the further action: reset with complete hotplug, or reset without
hotplug. However, that's not enough for those PCI devices whose
drivers can't support EEH, or those PCI devices without driver.
So we need do so-called "partial hotplug" on basis of PCI devices.
In the situation, part of PCI devices of the specific PE are
unplugged and plugged again after PE reset.

The patch changes pcibios_add_pci_devices() so that it can support
full hotplug and so-called "partial" hotplug based on device-tree
or real hardware. It's notable that pci_of_scan.c has been changed
for a bit in order to support the "partial" hotplug based on dev-tree.

Most of the generic code already supports that, we just need to
plumb it properly on our side.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Currently, we're trasversing the EEH devices list using list_for_each_entry().
That's not safe enough because the EEH devices might be removed from
its parent PE while doing iteration. The patch replaces that with
list_for_each_entry_safe().
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

When we do normal hotplug, the PE (shadow EEH structure) shouldn't be
kept around.

However, we need to keep it if the hotplug an artifial one caused by
EEH errors recovery.

Since we remove EEH device through the PCI hook pcibios_release_device(),
the flag "purge_pe" passed to various functions is meaningless. So the patch
removes the meaningless flag and introduce new flag "EEH_PE_KEEP"
to save the PE while doing hotplug during EEH error recovery.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The patch overrides pcibios_release_device() to release EEH
resources (EEH cache, unbinding EEH device) for the indicated PCI
device.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Make some functions public in order to support hotplug on either specific
PCI bus or PCI device in future.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We will rely on pcibios_release_device() to remove the EEH cache
and unbind EEH device for the specific PCI device. So we shouldn't
hold the reference to the PCI device from EEH cache and EEH device.
Otherwise, pcibios_release_device() won't be called as we expected.
The patch removes the reference to the PCI device in EEH core.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

During Machine Check interrupt on pseries platform, R3 generally points to
memory region inside RTAS (FWNMI) area. We see r3 corruption because when RTAS
delivers the machine check exception it passes the address inside FWNMI area
with the top most bit set. This patch fixes this issue by masking top two bit
in machine check exception handler.
Signed-off-by: NMahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The presence or absence of EBB is advertised to userspace via the presence
or absence of PPC_FEATURE2_EBB in cpu_user_features2.

Because the kernel can be built without PMU support, we should only add
PPC_FEATURE2_EBB to cpu_user_features2 when we successfully register the
power8 PMU support.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The Kconfig symbol HOTPLUG was removed with commit 40b31360 ("Finally
eradicate CONFIG_HOTPLUG"). But there's still one select statement for
that symbol. It seems that select statement was added after the patch to
remove CONFIG_HOTPLUG was submitted. Anyhow, it is useless and can be
dropped.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Reviewed-by: NSrivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

In hard_irq_disable(), we accessed the PACA before we hard disabled
the interrupts, potentially causing a warning as get_paca() will
us debug_smp_processor_id().

Move that to after the disabling, and also use local_paca directly
rather than get_paca() to avoid several redundant and useless checks.
Signed-off-by: NTiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Module CRCs are implemented as absolute symbols that get resolved by
a linker script. We build an intermediate .o that contains an
unresolved symbol for each CRC. genksysms parses this .o, calculates
the CRCs and writes a linker script that "resolves" the symbols to
the calculated CRC.

Unfortunately the ppc64 relocatable kernel sees these CRCs as symbols
that need relocating and relocates them at boot. Commit d4703aef
(module: handle ppc64 relocating kcrctabs when CONFIG_RELOCATABLE=y)
added a hook to reverse the bogus relocations. Part of this patch
created a symbol at 0x0:

# head -2 /proc/kallsyms
0000000000000000 T reloc_start
c000000000000000 T .__start

This reloc_start symbol is causing lots of confusion to perf. It
thinks reloc_start is a massive function that stretches from 0x0 to
0xc000000000000000 and we get various cryptic errors out of perf,
including:

problem incrementing symbol count, skipping event

This patch removes the  reloc_start linker script label and instead
defines it as PHYSICAL_START. We also need to wrap it with
CONFIG_PPC64 because the ppc32 kernel can set a non zero
PHYSICAL_START at compile time and we wouldn't want to subtract
it from the CRCs in that case.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Acked-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

POWER8 comes with two different PVRs.  This patch enables the additional
PVR in the cputable.

The existing entry (PVR=0x4b) is renamed to POWER8E and the new entry
(PVR=0x4d) is given POWER8.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

CONFIG_USB_EHCI_MXC selects the old i.mx USB driver, which does not support
device tree.

Select the USB chipidea driver instead, so that USB can be functional on i.mx.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The em_x270_mci_setpower() and em_x270_usb_hub_init() functions
call regulator_enable(), which may return an error that must
be checked.

This changes the em_x270_usb_hub_init() function to bail out
if it fails, and changes the pxamci_platform_data->setpower
callback so that the a failed em_x270_mci_setpower call
can be propagated by the pxamci driver into the mmc core.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: NChris Ball <cjb@laptop.org>
[olof: fixed order of regulator_enable() and test in em_x270_usb_hub_init]
Signed-off-by: NOlof Johansson <olof@lixom.net>

Fix the following compilation warning:

  arch/arm/mach-zynq/common.c:110:2: warning: initialization from incompatible pointer type [enabled by default]
  arch/arm/mach-zynq/common.c:110:2: warning: (near initialization for ‘__mach_desc_XILINX_EP107.restart’) [enabled by default]
Signed-off-by: NVincent Stehlé <vincent.stehle@freescale.com>
Cc: Robin Holt <holt@sgi.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: trivial@kernel.org
Signed-off-by: NOlof Johansson <olof@lixom.net>

Fix the following compilation warning:

  arch/arm/mach-keystone/keystone.c:74:2: warning: initialization from incompatible pointer type [enabled by default]
  arch/arm/mach-keystone/keystone.c:74:2: warning: (near initialization for ‘__mach_desc_KEYSTONE.restart’) [enabled by default]
Signed-off-by: NVincent Stehlé <vincent.stehle@freescale.com>
Cc: Robin Holt <holt@sgi.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: trivial@kernel.org
Signed-off-by: NOlof Johansson <olof@lixom.net>

Commit ff701306 (arm64: use common reboot infrastructure) converted the
arm_pm_restart declaration to the new reboot infrastructure but missed
the actual definition.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Secondary CPUs write to __boot_cpu_mode with caches disabled, and thus a
cached value of __boot_cpu_mode may be incoherent with that in memory.
This could lead to a failure to detect mismatched boot modes.

This patch adds flushing to ensure that writes by secondaries to
__boot_cpu_mode are made visible before we test against it.
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <cdall@cs.columbia.edu>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Midway adds new register fields to the coherency control registers, so
writing absolute values will break on Midway. Change the register
accesses to only modify the necessary and common fields in order to
support both Midway and Highbank.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Commit 8ef6e620 (ARM: footbridge: use
fixed PCI i/o mapping) broke booting on my netwinder.  Before that,
everything boots fine.  Since then, it crashes on boot.

With earlyprintk, I see it BUG-ing like so:
kernel BUG at lib/ioremap.c:27!
Internal error: Oops - BUG: 0 [#1] ARM
...
[<c0139b54>] (ioremap_page_range+0x128/0x154) from [<c02e6a6c>] (dc21285_setup+0xd0/0x114)
[<c02e6a6c>] (dc21285_setup+0xd0/0x114) from [<c02e4874>] (pci_common_init+0xa0/0x298)
[<c02e4874>] (pci_common_init+0xa0/0x298) from [<c02e793c>] (netwinder_pci_init+0xc/0x18)
[<c02e793c>] (netwinder_pci_init+0xc/0x18) from [<c02e27d0>] (do_one_initcall+0xb4/0x180)
...

Russell points out it's because of overlapping PCI mappings that was
added with the aforementioned commit.  Rob thought the code would re-use
the static mapping, but that turns out to not be the case and instead
hits the BUG further down.

After deleting this hunk as suggested by Russel, the system boots up fine
again and all my PCI devices work (IDE, ethernet, the DC21285).
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Cc: stable@vger.kernel.org	# v3.5+
Signed-off-by: NOlof Johansson <olof@lixom.net>

Some of the ARM_ERRATA selection is not done in the initial SOC support
patches. This patch selects 2 new ARM_ERRATA's and removes one which was
actually fixed.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@st.com>
[olof: reorder new errata entries]
Signed-off-by: NOlof Johansson <olof@lixom.net>