Intel BayTrail has almost the same Low Power Subsystem than Lynxpoint with
few differences. Peripherals are clocked with different speeds (typically
lower) and the clock is not always gated. To support this we add
possibility to share a common fixed rate clock and make clock gating
optional.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: NMike Turquette <mturquette@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

With the introduction of ACPI scan handlers, ACPI device objects
with an ACPI scan handler attached to them must not be bound to
by ACPI drivers any more.  Unfortunately, however, the ACPI video
driver attempts to do just that if there is a _ROM ACPI control
method defined under a device object with an ACPI scan handler.

Prevent that from happening by making the video driver's "add"
routine check if the device object already has an ACPI scan handler
attached to it and return an error code in that case.

That is not sufficient, though, because acpi_bus_driver_init() would
then clear the device object's driver_data that may be set by its
scan handler, so for the fix to work acpi_bus_driver_init() has to be
modified to leave driver_data as is on errors.

References: https://bugzilla.kernel.org/show_bug.cgi?id=58091Bisected-and-tested-by: NDmitry S. Demin <dmitryy.demin@gmail.com>
Reported-and-tested-by: NJason Cassell <bluesloth600@gmail.com>
Tracked-down-by: NAaron Lu <aaron.lu@intel.com>
Cc: 3.9+ <stable@kernel.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: NAaron Lu <aaron.lu@intel.com>

Commit 9f29ab11 ("ACPI / scan: do not match drivers against objects
having scan handlers") introduced a boot regression on Tony's ia64 HP
rx2600.  Tony says:

  "It panics with the message:

   Kernel panic - not syncing: Unable to find SBA IOMMU: Try a generic or DIG kernel

   [...] my problem comes from arch/ia64/hp/common/sba_iommu.c
   where the code in sba_init() says:

        acpi_bus_register_driver(&acpi_sba_ioc_driver);
        if (!ioc_list) {

   but because of this change we never managed to call ioc_init()
   so ioc_list doesn't get set up, and we die."

Revert it to avoid this breakage and we'll fix the problem it attempted
to address later.
Reported-by: NTony Luck <tony.luck@gmail.com>
Cc: 3.9+ <stable@vger.kernel.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit b3785492 (ACPI / PM: Do not power manage devices in unknown
initial states) added code to force devices without _PSC, but having
_PS0 defined in the ACPI namespace, into ACPI power state D0 by
executing _PS0 for them.  That turned out to break Toshiba P870-303,
however, so revert that code.

References: https://bugzilla.kernel.org/show_bug.cgi?id=58201Reported-and-tested-by: NJerome Cantenot <jerome.cantenot@gmail.com>
Tracked-down-by: NLan Tianyu <tianyu.lan@intel.com>
Cc: 3.9+ <stable@vger.kernel.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

With the introduction of ACPI scan handlers, an ACPI device object
with an ACPI scan handler attached to it must not be bound to an ACPI
driver any more.  Therefore it doesn't make sense to match those
ACPI device objects against a newly registered ACPI driver in
acpi_bus_match(), so make that function return 0 if the device
object passed to it has an ACPI scan handler attached.

This also addresses a regression related to a broken ACPI table in
the BIOS, where it has defined a _ROM method under the PCI root
bridge object.  This causes the video module to treat that object
as a display controller device (since only display devices are
supposed to have a _ROM method defined according to the ACPI spec).
As a result, the ACPI video driver binds to the PCI root bridge
object and overwrites the previously assigned driver_data field of
it, causing subsequent calls to acpi_get_pci_dev() to fail.

[rjw: Subject and changelog]
References: https://bugzilla.kernel.org/show_bug.cgi?id=58091Reported-by: NJason Cassell <bluesloth600@gmail.com>
Reported-and-bisected-by: NDmitry S. Demin <dmitryy.demin@gmail.com>
Cc: 3.9+ <stable@kernel.org>
Signed-off-by: NAaron Lu <aaron.lu@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Fix to return a negative error code in the acpi_gsi_to_irq() and
request_irq() error handling case instead of 0, as done elsewhere
in this function.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: NHuang Ying <ying.huang@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

This patch addresses kernel bug 56661. BIOS reports an incorrect
backlight value, causing the driver to switch off the backlight
completely during startup. This patch ignores the incorrect value from
BIOS.

References: https://bugzilla.kernel.org/show_bug.cgi?id=56661Signed-off-by: NAsh Willis <ashwillis@programmer.net>
Cc: All <stable@vger.kernel.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

On HP m4 lapops, BIOS reports minimum backlight on boot and
causes backlight to dim completely. This ignores the initial backlight
values and set to max brightness.

References: https://bugs.launchpad.net/bugs/1184501
Cc: All <stable@vger.kernel.org>
Signed-off-by: NAlex Hung <alex.hung@canonical.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The following warning was seen on 3.9 when a corrected PCIe error was being
handled by the AER subsystem.

WARNING: at .../drivers/pci/search.c:214 pci_get_dev_by_id+0x8a/0x90()

This occurred because a call to pci_get_domain_bus_and_slot() was added to
cper_print_pcie() to setup for the call to cper_print_aer().  The warning
showed up because cper_print_pcie() is called in an interrupt context and
pci_get* functions are not supposed to be called in that context.

The solution is to move the cper_print_aer() call out of the interrupt
context and into aer_recover_work_func() to avoid any warnings when calling
pci_get* functions.
Signed-off-by: NLance Ortiz <lance.ortiz@hp.com>
Acked-by: NBorislav Petkov <bp@suse.de>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

Like on UL30VT, the ACPI video driver can't control backlight correctly on
Asus UL30A.  Vendor driver (asus-laptop) can work.  This patch is to
add "Asus UL30A" to ACPI video detect blacklist in order to use
asus-laptop for video control on the "Asus UL30A" rather than ACPI
video driver.
Signed-off-by: NBastian Triller <bastian.triller@gmail.com>
Cc: All <stable@vger.kernel.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Currently, drivers/acpi/device_pm.c depends on CONFIG_PM and all of
the functions defined in there are replaced with static inline stubs
if that option is unset.  However, CONFIG_PM means, roughly, "runtime
PM or suspend/hibernation support" and some of those functions are
useful regardless of that.  For example, they are used by the ACPI
fan driver for controlling fans and acpi_device_set_power() is called
during device removal.  Moreover, device initialization may depend on
setting device power states properly.

For these reasons, make the routines manipulating ACPI device power
states defined in drivers/acpi/device_pm.c available for CONFIG_PM
unset too.
Reported-by: NZhang Rui <rui.zhang@intel.com>
Reported-and-tested-by: NMichel Lespinasse <walken@google.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: 3.9+ <stable@vger.kernel.org>

When a PCI host bridge device receives a Bus Check notification, we
must re-enumerate starting with the bridge to discover changes (devices
that have been added or removed).

Prior to 668192b6 ("PCI: acpiphp: Move host bridge hotplug to
pci_root.c"), this happened in _handle_hotplug_event_bridge().  After that
commit, _handle_hotplug_event_bridge() is not installed for host bridges,
and the host bridge notify handler, _handle_hotplug_event_root() did not
re-enumerate.

This patch adds re-enumeration to _handle_hotplug_event_root().

This fixes cases where we don't notice the addition or removal of
PCI devices, e.g., the PCI-to-USB ExpressCard in the bugzilla below.

[bhelgaas: changelog, references]
Reference: https://lkml.kernel.org/r/CAAh6nkmbKR3HTqm5ommevsBwhL_u0N8Rk7Wsms_LfP=nBgKNew@mail.gmail.com
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=57961Reported-by: NGavin Guo <tuffkidtt@gmail.com>
Tested-by: NGavin Guo <tuffkidtt@gmail.com>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Reviewed-by: NJiang Liu <jiang.liu@huawei.com>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
CC: stable@vger.kernel.org	# v3.9+

Following commit 6b772e8f (ACPI: Update PNPID match handling for
notify), the acpi_scan_init_hotplug() calls acpi_set_pnp_ids() which
allocates acpi_hardware_id and copies a few strings (kstrdup). If the
devices does not have hardware_id set, the function exits without
freeing the previously allocated ids (and kmemleak complains). This
patch calls simply changes 'return' on error to a 'goto out' which
calls acpi_free_pnp_ids().
Reported-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Reviewed-by: NToshi Kani <toshi.kani@hp.com>
Tested-by: NToshi Kani <toshi.kani@hp.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The DMA controller in Lynxpoint is enumerated as a regular ACPI device now. To
work properly it is using the LPSS root clock as a functional clock. That's why
we have to register the clock device accordingly to the ACPI ID of the DMA
controller. The acpi_lpss.c module is responsible to do the job.

This patch also removes hardcoded name of the DMA device in clk-lpt.c and the
name of the root clock in acpi_lpss.c.
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Since we have CSRT only to get additional DMA controller resources, let's get
rid of drivers/acpi/csrt.c and move its logic inside ACPI DMA helpers code.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

The Thinkpad e530's BIOS notifies the AC device first and then
sleeps for certain amount of time before doing real work in the
EC event handler (_Qxx):

 Method (_Q27, 0, NotSerialized)
 {
       Notify (AC, 0x80)
       Sleep (0x03E8)
       Store (Zero, PWRS)
       PNOT ()
 }

This causes the AC driver to report an outdated AC state to user
space, because it reads the state information from the device while
the EC handler is sleeping.

Introduce a quirk to cause the AC driver to wait in acpi_ac_notify()
before calling acpi_ac_get_state() on systems known to have this
problem and add Thinkpad e530 to the list of quirky machines (with
a 1s delay which has been verified to be sufficient for that
machine).

[rjw: Changelog]
References: https://bugzilla.kernel.org/show_bug.cgi?id=45221Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The EC driver works abnormally with IBF flag always set.
IBF means "The host has written a byte of data to the command
or data port, but the embedded controller has not yet read it".
If IBF is set in the EC status and not cleared, this will cause
all subsequent EC requests to fail with a timeout error.

Change the EC driver so that it doesn't refuse to restart a
transaction if IBF is set in the status.  Also increase the
number of transaction restarts to 5, as it turns out that 2
is not sufficient in some cases.

This bug happens on several different machines (Asus V1S,
Dell Latitude E6530, Samsung R719, Acer Aspire 5930G,
Sony Vaio SR19VN and others).

[rjw: Changelog]
References: https://bugzilla.kernel.org/show_bug.cgi?id=14733
References: https://bugzilla.kernel.org/show_bug.cgi?id=15560
References: https://bugzilla.kernel.org/show_bug.cgi?id=15946
References: https://bugzilla.kernel.org/show_bug.cgi?id=42945
References: https://bugzilla.kernel.org/show_bug.cgi?id=48221Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Cc: All <stable@vger.kernel.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

On HP 1000 lapops, BIOS reports minimum backlight on boot and
causes backlight to dim completely. This ignores the initial backlight
values and set to max brightness.

References:: https://bugs.launchpad.net/bugs/1167760Signed-off-by: NAlex Hung <alex.hung@canonical.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The system suspend routine of the ACPI processor driver saves
the BUS_MASTER_RLD register and its resume routine restores it.
However, there can be only one such register in the system and it
really should be saved after non-boot CPUs have been offlined and
restored before they are put back online during resume.

For this reason, move the saving and restoration of BUS_MASTER_RLD
to syscore suspend and syscore resume, respectively, and drop the no
longer necessary suspend/resume callbacks from the ACPI processor
driver.
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

This change fixes a problem introduced by recent commit c34c82bc
(ACPICA: Predefine names: Add allowed argument types to master info
table) in 20130328 where _INI methods are no longer executed properly
because of a memory block that is not initialized properly.  ACPICA
BZ1016. Tomasz Nowicki <tomasz.nowicki@linaro.org>

References: https://bugs.acpica.org/show_bug.cgi?id=1016Signed-off-by: NTomasz Nowicki <tomasz.nowicki@linaro.org>
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Fixes a possible memory leak in the error exit path introduced by
recent commit 388a9902 ("ACPICA: _OSI Support: handle any errors from
acpi_os_acquire_mutex()").

[rjw: Changelog]
Signed-off-by: NJung-uk Kim <jkim@FreeBSD.org>
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Can only happen under these conditions: 1) The DSDT version is 1,
meaning integers are 32-bits.  2) The field is between 33 and 64
bits long.

It applies cleanly back to ACPICA 20100806+ (Linux v2.6.37+).
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Cc: 2.6.37+ <stable@vger.kernel.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Supply a function (proc_remove()) to remove a proc entry (and any subtree
rooted there) by proc_dir_entry pointer rather than by name and (optionally)
root dir entry pointer.  This allows us to eliminate all remaining pde->name
accesses outside of procfs.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Acked-by: NGrant Likely <grant.likely@linaro.or>
cc: linux-acpi@vger.kernel.org
cc: openipmi-developer@lists.sourceforge.net
cc: devicetree-discuss@lists.ozlabs.org
cc: linux-pci@vger.kernel.org
cc: netdev@vger.kernel.org
cc: netfilter-devel@vger.kernel.org
cc: alsa-devel@alsa-project.org
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Commit 4ae46bef "Thermal: Introduce thermal_zone_trip_update()"
introduced a regression causing the fan to be always on even when
the system is idle.

My original idea in that commit is that:
 - when the current temperature is above the trip point,
   keep the fan on, even if the temperature is dropping.
 - when the current temperature is below the trip point,
   turn on the fan when the temperature is raising,
   turn off the fan when the temperature is dropping.

But this is what the code actually does:
 - when the current temperature is above the trip point,
   the fan keeps on.
 - when the current temperature is below the trip point,
   the fan is always on because thermal_get_trend()
   in driver/acpi/thermal.c returns THERMAL_TREND_RAISING.
Thus the fan keeps running even if the system is idle.

Fix this in drivers/acpi/thermal.c.

[rjw: Changelog]
References: https://bugzilla.kernel.org/show_bug.cgi?id=56591
References: https://bugzilla.kernel.org/show_bug.cgi?id=56601
References: https://bugzilla.kernel.org/show_bug.cgi?id=50041#c45Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Tested-by: NMatthias <morpheusxyz123@yahoo.de>
Tested-by: NVille Syrjälä <syrjala@sci.fi>
Cc: 3.7+ <stable@vger.kernel.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

acpi_video_bus_get_devices() may fail due to some video output device
doesn't have the _ADR method, and in this case, the error processing
is to simply free the video structure in acpi_video_bus_add(), while
leaving those already registered video output devices in the wild,
which means for some video output device, we have already registered
a backlight interface and installed a notification handler for it.
So it can happen when user is using this system, on hotkey pressing,
the notification handler will send a keycode through a non-existing
input device, causing kernel freeze.

To solve this problem, free all those already registered video output
devices once something goes wrong in acpi_video_bus_get_devices(), so
that no wild backlight interfaces and notification handlers exist.

References: https://bugzilla.kernel.org/show_bug.cgi?id=51731
Reported-and-tested-by: <i-tek@web.de>
Signed-off-by: NAaron Lu <aaron.lu@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Commit 53aac44c (ACPI: Store valid ACPI tables passed via early initrd
in reserved memblock areas) introduced acpi_initrd_override() that
passes a wrong value as the second argument to memblock_reserve().

Namely, the second argument of memblock_reserve() is the size of the
region, not the address of the top of it, so make
acpi_initrd_override() pass the size in there as appropriate.

[rjw: Changelog]
Signed-off-by: NWang YanQing <udknight@gmail.com>
Acked-by: NYinghai Lu <yinghai@kernel.org>
Cc: 3.8+ <stable@vger.kernel.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The en_core_tk_irqen flag is set in all the cpuidle driver which
means it is not necessary to specify this flag.

Remove the flag and the code related to it.
Signed-off-by: NDaniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>  # for mach-omap2/*
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Currently we decide if the _BQC is using index by first setting the
level to maximum, and then check if _BQC returned maximum; if not, we
say it is using index.

This is not true for some buggy systems, where the _BQC method will
always return a constant value(e.g. 0 or 100 for the two broken system)
and thus break the current logic. So this patch tries to enhance the
quirk detect logic for _BQC: we do this by picking a test_level, it can
be the maximum level or the mininum one based on some condition. And we
don't make the assumption that if _BQC returned a value that is not what
we just set, it must be using an index. Instead, we will compare the
value returned from _BQC and if it doesn't match, see if the returned
value is an index. And if still no, clear the capability of _BQC.

References: https://bugzilla.kernel.org/show_bug.cgi?id=42861
References: https://bugzilla.kernel.org/show_bug.cgi?id=56011Reported-and-tested-by: NArtem Savkov <artem.savkov@gmail.com>
Reported-by: NLuis Medinas <lmedinas@gmail.com>
Reported-by: NCheppes <cheppes@mailinator.com>
Signed-off-by: NAaron Lu <aaron.lu@intel.com>
Acked-by: NZhang Rui <rui.zhang@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Both sub-drivers of the "PCI Root Bridge ("pci_bridge")" driver, "acpiphp"
and "pci_slot", have been converted to hook directly into the PCI core.

With the conversions there are no remaining usages of the 'struct
acpi_pci_driver' list based infrastructure.  This patch removes it.
Signed-off-by: NMyron Stowe <myron.stowe@redhat.com>
Signed-off-by: NJiang Liu <jiang.liu@huawei.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Reviewed-by: NYinghai Lu <yinghai@kernel.org>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Toshi Kani <toshi.kani@hp.com>

Currently the pci_slot driver doesn't update PCI slot devices when PCI
device hotplug event happens, which may cause memory leak and returning
stale information to user.

Now the pci_slot driver has been changed as built-in driver, so invoke
PCI slot enumeration and destroy routines directly from the PCI core.
And remove ACPI PCI sub-driver related code because it isn't needed
any more.

[bhelgas: removed "extern" from function declarations]
Signed-off-by: NJiang Liu <jiang.liu@huawei.com>
Signed-off-by: NYijing Wang <wangyijing@huawei.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Reviewed-by: NYinghai Lu <yinghai@kernel.org>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Toshi Kani <toshi.kani@hp.com>

Certain external interfaces need to update object references
without holding the interpreter or namespace mutex objects. To
prevent race conditions, add a spinlock around the increment
and decrement of the reference counts for internal ACPI
objects. Reported by Andriy Gapon (avg@FreeBSD.org).
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NAndriy Gapon <avg@FreeBSD.org>
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Fix a warning on 64-bit for a length value. Cast to 32-bit since
the length is related to an ACPI table.
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

This option is not used and is obsolete.
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

For the case where an attempt is made to take an Index() beyond
the end of a String, Buffer, or Package, emit the actual length
of the object to the error message. Helpful for debugging.
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

This change removes a size mismatch warning if the legacy
length field for a GPE register set is larger than the 64-bit
GAS structure can accomodate. GPE register sets can be larger
than the 255 bit limitation of the GAS structure. Linn Crosetto
(linn@hp.com).
Signed-off-by: NLinn Crosetto <linn@hp.com>
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Reported by Colin King.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Remove an extraneous minus/dash. Reported by Colin Ian King.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

No functional change.  Includes parameter rename from Tang Chen.
Signed-off-by: NTang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Check for any errors. Handles possible timeout case if
ACPI_WAIT_FOREVER is changed to be less than "forever".
Jung-uk Kim.
Signed-off-by: NJung-uk Kim <jkim@FreeBSD.org>
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

This change adds the infrastructure to enable typechecking
on incoming arguments for the predefined methods/objects. It
does not actually contain the code that will fully utilize this
information. Also condenses some duplicate code for the predefined
names into a new module, utilities/utpredef.c
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>