use per-CPU counters, like other TC actions do, instead of maintaining one
set of stats across all cores. This allows updating act_csum stats without
the need of protecting them using spin_{,un}lock_bh() invocations.
Signed-off-by: NDavide Caratti <dcaratti@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It takes 1sec for bond link down notification to hit user-space
when all slaves of the bond go down. 1sec is too long for
protocol daemons in user-space relying on bond notification
to recover (eg: multichassis lag implementations in user-space).
Since the link event code already marks team device port link events
 as urgent, this patch moves the code to cover all lag ports and master.
Signed-off-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
10GbE Intel Wired LAN Driver Updates 2018-01-23

This series contains updates to ixgbe only.

Shannon Nelson provides an implementation of the ipsec hardware offload
feature for the ixgbe driver for these devices: x540, x550, 82599.

The ixgbe NICs support ipsec offload for 1024 Rx and 1024 Tx Security
Associations (SAs), using up to 128 inbound IP addresses, and using the
rfc4106(gcm(aes)) encryption.  This code does not yet support checksum
offload, or TSO in conjunction with the ipsec offload - those will be
added in the future.

This code shows improvements in both packet throughput and CPU utilization.
For example, here are some quicky numbers that show the magnitude of the
performance gain on a single run of "iperf -c <dest>" with the ipsec
offload on both ends of a point-to-point connection:

	9.4 Gbps - normal case
	7.6 Gbps - ipsec with offload
	343 Mbps - ipsec no offload
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sebastian Reichel says:

====================
GEHC Bx50 Switch Support

This adds support for the internal switch found in GE Healthcare
B450v3, B650v3 and B850v3. All devices use a GPIO bitbanged MDIO
bus to communicate with the switch and a PCIe based network card
for exchanging network data. The cpu network data link requires,
that the switch's internal phy interface is enabled, so support
for that is added by the first patch in this series.

The patch series is based on v4.15-rc8.

Changes since PATCHv4:
 * Introduce dsa_port_link_(un)register_of and mark the fixed
   variant static.
 * Update patch description to describe the phy<->phy connection
   from i210 to the Marvell switch
Changes since PATCHv3:
 * Enable the phy in dsa_port_setup() instead of abusing the
   fixed link setup function
Changes since PATCHv2:
 * Add phy nodes to switch in bx50.dtsi and reference them
   from switch ports
 * Enable cpu-port's phy based on 'phy-handle' instead of 'phy-mode'
Changes since PATCHv1:
 * Use 'marvell,mv88e6085' instead of introducing compatible
   string for mv88e6240.
 * Fix indention of DT nodes
 * Only enable 'cpu' phy, if explicitly set to "internal".
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds support for the Marvell switch and names the network
ports according to the labels, that can be found next to the
connectors. The switch is connected to the host system using a
PCI based network card.

The PCI bus configuration has been written using the following
information:

root@b450v3# lspci -tv
-[0000:00]---00.0-[01]----00.0  Intel Corporation I210 Gigabit Network Connection
root@b450v3# lspci -nn
00:00.0 PCI bridge [0604]: Synopsys, Inc. Device [16c3:abcd] (rev 01)
01:00.0 Ethernet controller [0200]: Intel Corporation I210 Gigabit Network Connection [8086:1533] (rev 03)
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds support for the Marvell switch and names the network
ports according to the labels, that can be found next to the
connectors. The switch is connected to the host system using a
PCI based network card.

The PCI bus configuration has been written using the following
information:

root@b650v3# lspci -tv
-[0000:00]---00.0-[01]----00.0  Intel Corporation I210 Gigabit Network Connection
root@b650v3# lspci -nn
00:00.0 PCI bridge [0604]: Synopsys, Inc. Device [16c3:abcd] (rev 01)
01:00.0 Ethernet controller [0200]: Intel Corporation I210 Gigabit Network Connection [8086:1533] (rev 03)
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds support for the Marvell switch and names the network
ports according to the labels, that can be found next to the
connectors ("ID", "IX", "ePort 1", "ePort 2"). The switch is
connected to the host system using a PCI based network card.

The PCI bus configuration has been written using the following
information:

root@b850v3# lspci -tv
-[0000:00]---00.0-[01]----00.0-[02-05]--+-01.0-[03]----00.0  Intel Corporation I210 Gigabit Network Connection
                                        +-02.0-[04]----00.0  Intel Corporation I210 Gigabit Network Connection
                                        \-03.0-[05]--
root@b850v3# lspci -nn
00:00.0 PCI bridge [0604]: Synopsys, Inc. Device [16c3:abcd] (rev 01)
01:00.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8605 PCI Express 4-port Gen2 Switch [10b5:8605] (rev ab)
02:01.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8605 PCI Express 4-port Gen2 Switch [10b5:8605] (rev ab)
02:02.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8605 PCI Express 4-port Gen2 Switch [10b5:8605] (rev ab)
02:03.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8605 PCI Express 4-port Gen2 Switch [10b5:8605] (rev ab)
03:00.0 Ethernet controller [0200]: Intel Corporation I210 Gigabit Network Connection [8086:1533] (rev 03)
04:00.0 Ethernet controller [0200]: Intel Corporation I210 Gigabit Network Connection [8086:1533] (rev 03)
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

B850v3, B650v3 and B450v3 all have a GPIO bit banged MDIO bus to
communicate with a Marvell switch. On all devices the switch is
connected to a PCI based network card, which needs to be referenced
by DT, so this also adds the common PCI root node.
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds support for enabling the internal PHY for a 'cpu' port.
It has been tested on GE B850v3,  B650v3 and B450v3, which have a
built-in MV88E6240 switch hardwired to a PCIe based network card.
On these machines the internal PHY of the i210 network card and
the Marvell switch are connected to each other and must be enabled
for properly using the switch. While the i210 PHY will be enabled
when the network interface is enabled, the switch's port is not
exposed as network interface. Additionally the mv88e6xxx driver
resets the chip during probe, so the PHY is disabled without this
patch.
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

en_rx_am.c was deleted in 'net-next' but had a bug fixed in it in
'net'.

The esp{4,6}_offload.c conflicts were overlapping changes.
The 'out' label is removed so we just return ERR_PTR(-EINVAL)
directly.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With all the support code in place we can now link in the ipsec
offload operations and set the ESP feature flag for the XFRM
subsystem to see.
Signed-off-by: NShannon Nelson <shannon.nelson@oracle.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add a simple statistic to count the ipsec offloads.
Signed-off-by: NShannon Nelson <shannon.nelson@oracle.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If the skb has a security association referenced in the skb, then
set up the Tx descriptor with the ipsec offload bits.  While we're
here, we fix an oddly named field in the context descriptor struct.
Signed-off-by: NShannon Nelson <shannon.nelson@oracle.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If the chip sees and decrypts an ipsec offload, set up the skb
sp pointer with the ralated SA info.  Since the chip is rude
enough to keep to itself the table index it used for the
decryption, we have to do our own table lookup, using the
hash for speed.
Signed-off-by: NShannon Nelson <shannon.nelson@oracle.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

On a chip reset most of the table contents are lost, so must be
restored.  This scans the driver's ipsec tables and restores both
the filled and empty table slots to their pre-reset values.
Signed-off-by: NShannon Nelson <shannon.nelson@oracle.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add the functions for setting up and removing offloaded SAs (Security
Associations) with the x540 hardware.  We set up the callback structure
but we don't yet set the hardware feature bit to be sure the XFRM service
won't actually try to use us for an offload yet.

The software tables are made up to mimic the hardware tables to make it
easier to track what's in the hardware, and the SA table index is used
for the XFRM offload handle.  However, there is a hashing field in the
Rx SA tracking that will be used to facilitate faster table searches in
the Rx fast path.
Signed-off-by: NShannon Nelson <shannon.nelson@oracle.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Set up the data structures to be used by the ipsec offload.
Signed-off-by: NShannon Nelson <shannon.nelson@oracle.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add in the code for running and stopping the hardware ipsec
encryption/decryption engine.  It is good to keep the engine
off when not in use in order to save on the power draw.
Signed-off-by: NShannon Nelson <shannon.nelson@oracle.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add a few routines to make access to the ipsec registers just a little
easier, and throw in the beginnings of an initialization.
Signed-off-by: NShannon Nelson <shannon.nelson@oracle.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Pull networking fixes from David Miller:

 1) Fix divide by zero in mlx5, from Talut Batheesh.

 2) Guard against invalid GSO packets coming from untrusted guests and
    arriving in qdisc_pkt_len_init(), from Eric Dumazet.

 3) Similarly add such protection to the various protocol GSO handlers.
    From Willem de Bruijn.

 4) Fix regression added to IGMP source address checking for IGMPv3
    reports, from Felix Feitkau.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  tls: Correct length of scatterlist in tls_sw_sendpage
  be2net: restore properly promisc mode after queues reconfiguration
  net: igmp: fix source address check for IGMPv3 reports
  gso: validate gso_type in GSO handlers
  net: qdisc_pkt_len_init() should be more robust
  ibmvnic: Allocate and request vpd in init_resources
  ibmvnic: Revert to previous mtu when unsupported value requested
  ibmvnic: Modify buffer size and number of queues on failover
  rds: tcp: compute m_ack_seq as offset from ->write_seq
  usbnet: silence an unnecessary warning
  cxgb4: fix endianness for vlan value in cxgb4_tc_flower
  cxgb4: set filter type to 1 for ETH_P_IPV6
  net/mlx5e: Fix fixpoint divide exception in mlx5e_am_stats_compare

Clean up the ipsec/macsec descriptor bit definitions to match the rest
of the defines and file organization.  Also recognise the bit-definition
overlap in the error mask macro.
Signed-off-by: NShannon Nelson <shannon.nelson@oracle.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Commit 97a6ec4a ("rhashtable: Change rhashtable_walk_start to
return void") only initialized ret for the first time, when going
to again path, the next tsp could be NULL. Without resetting ret,
cb_done would be called with tsp as NULL.

A kernel crash was caused by this when running sctpdiag testcase
in sctp-tests.

Note that this issue doesn't affect net.git yet.

Fixes: 97a6ec4a ("rhashtable: Change rhashtable_walk_start to return void")
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Acked-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pointers txr and rxr are being initialized and a few statements later
are being assigned new values without the original values ever being
read. The initialized values are therefore redundant and can be
removed.

Cleans up clang warnings:
drivers/net/ethernet/broadcom/bnx2.c:5821:28: warning: Value stored to
'txr' during its initialization is never read
drivers/net/ethernet/broadcom/bnx2.c:5822:28: warning: Value stored to
'rxr' during its initialization is never read
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since both first_rx_ctx and rx_skb are the head of rx ctx, it not
necessary to use two structure members to statically indicate
the head of rx ctx. So first_rx_ctx is removed.

CC: Srinivas Eeda <srinivas.eeda@oracle.com>
CC: Joe Jin <joe.jin@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: NZhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
Kernel doc fixes for networking

This patch series fixes kernel doc warnings found while running make htmldocs
pertaining to the networking subsystem. There is a finaly set of warnings due
to PHYLINK which I have not been able to resolve yet.

The last patch could thereoteically be applied to 'net' since the commit
referenced by the Fixes: tag is present in v4.15-rcX.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes the following warnings:
./net/core/dev.c:6438: warning: No description found for parameter 'extack'
./net/core/dev.c:6461: warning: No description found for parameter 'extack'

Fixes: 42ab19ee ("net: Add extack to upper device linking")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the @dev comment, since we do not have a net_device argument, fixes the
following kernel doc warning: /net/core/dev.c:1707: warning: Excess function
parameter 'dev' description in 'call_netdevice_notifiers_info'
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We forgot to update the kernel doc header above sfp_register_upstream()

Fixes: c19bb000 ("sfp: convert to fwnode")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the documentation warning:

include/linux/netdevice.h:1939: warning: Excess struct member 'carrier_changes' description in 'net_device'
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Fixes: b2d3bcfa ("net: core: Expose number of link up/down transitions")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes the following sparse warning:

drivers/net/ethernet/aquantia/atlantic/aq_pci_func.c:50:34: warning:
 symbol 'hw_atl_boards' was not declared. Should it be static?

Fixes: 4948293f ("net: aquantia: Introduce new AQC devices and capabilities")
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Acked-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix to return error code -ENOMEM from the aq_ndev_alloc() error
handling case instead of 0, as done elsewhere in this function.

Fixes: 23ee07ad ("net: aquantia: Cleanup pci functions module")
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Acked-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix to return error code -EINVAL instead of 0 when num_vfs above
limit_vfs, as done elsewhere in this function.

Fixes: 0dc78621 ("nfp: handle SR-IOV already enabled when driver is probing")
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix bug that causes _absolute_ rtsym sizes of > 8 bytes (as per symbol
table) to result in incorrect space used during a TLV-based debug dump.

Detail: The size calculation stage calculates the correct size (size of
the rtsym address field == 8), while the dump uses the size in the table
to calculate the TLV size to reserve. Symbols with size <= 8 are handled
OK due to aligning sizes to 8, but including any absolute symbol with
listed size > 8 leads to an ENOSPC error during the dump.

Fixes: da762863 ("nfp: fix absolute rtsym handling in debug dump")
Signed-off-by: NCarl Heymann <carl.heymann@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit bdcf0a42 ("kernel: make groups_sort calling a responsibility
group_info allocators") appears to break nfsd rootsquash in a pretty
major way.

It adds a call to groups_sort() inside the loop that copies/squashes
gids, which means the valid gids are sorted along with the following
garbage.  The net result is that the highest numbered valid gids are
replaced with any lower-valued garbage gids, possibly including 0.

We should sort only once, after filling in all the gids.

Fixes: bdcf0a42 ("kernel: make groups_sort calling a responsibility ...")
Signed-off-by: NBen Hutchings <ben.hutchings@codethink.co.uk>
Acked-by: NJ. Bruce Fields <bfields@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Similarly to tx ring, xdp_rxq_info is only registered
when !tfile->detached, so we need to avoid calling
xdp_rxq_info_unreg() twice too. The helper tun_cleanup_tx_ring()
already checks for this properly, so it is correct to put
xdp_rxq_info_unreg() just inside there.

Reported-by: syzbot+1c788d7ce0f0888f1d7f@syzkaller.appspotmail.com
Fixes: 8565d26b ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net")
Cc: Jason Wang <jasowang@redhat.com>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In orangefs_devreq_read, there is a loop which picks an op off the list
of pending ops.  If the loop fails to find an op, there is nothing to
read, and it returns EAGAIN.  If the op has been given up on, the loop
is restarted via a goto.  The bug is that the variable which the found
op is written to is not reinitialized, so if there are no more eligible
ops on the list, the code runs again on the already handled op.

This is triggered by interrupting a process while the op is being copied
to the client-core.  It's a fairly small window, but it's there.
Signed-off-by: NMartin Brandenburg <martin@omnibond.com>
Cc: stable@vger.kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

set_op_state_purged can delete the op.
Signed-off-by: NMartin Brandenburg <martin@omnibond.com>
Cc: stable@vger.kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Jakub Kicinski says:

====================
net: sched: add extack support for cls offloads

I've dropped the tests from the series because test_offloads.py changes
will conflict with bpf-next patches.  I will send four more patches with
tests once bpf-next is merged back, hopefully still making it into 4.16 :)

v4:
 - rebase on top of Alex's changes.

---

Quentin says:

This series tries to improve user experience when eBPF hardware offload
hits error paths at load time. In particular, it introduces netlink
extended ack support in the nfp driver.

To that aim, transmission of the pointer to the extack object is piped
through the `change()` operation of the existing classifiers (patch 1 to
6). Then it is used for TC offload in the nfp driver (patch 8) and in
netdevsim (patch 9, selftest in patch 10). Patch 7 adds a helper to handle
extack messages in the core when TC offload is disabled on the net device.

For completeness extack is propagated for classifiers other than cls_bpf,
but it's up to the drivers to make use of it.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the recently added extack support for eBPF offload in the driver.
Signed-off-by: NQuentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pass a pointer to an extack object to nfp_app_xdp_offload() in order to
prepare for extack usage in the nfp driver. Next step will be to forward
this extack pointer to nfp_net_bpf_offload(), once this function is able
to use it for printing error messages.
Signed-off-by: NQuentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>