Currently the only init function in wm_adsp is called by the
codec driver early in its probe before the codec has been
registered with SOC.

This patch adds stubs for the codec_probe and codec_remove stages
and calls them from WM5102 and WM5110 codec drivers. This allows us
to hang anything that needs setup during the codec probe stage off
these functions without further modification of the codec drivers.
Signed-off-by: NRichard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The WM8997 and WM5102 codecs need to boost DVFS for higher sample rates.
Signed-off-by: NRichard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

In theory the ADSP driver should not need to know anything
about the codec it is part of. But the WM5102 needs DVFS
control based on ADSP clocking speed. This was being handled
by bundling part of the knowledge of this into the ADSP driver.

This change moves this handling out of the ADSP driver and
into the WM5102 driver.
Signed-off-by: NRichard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The WM5102 and WM8997 codecs have an internal dynamic clock booster.
When this booster is active, the DCVDD voltage must be increased.
If all the currently active audio paths can run with the root SYSCLK
we can disable the booster, allowing us to turn down DCVDD voltage
to save power.

Previously this was being done by having the booster enable bit set
as a side-effect of the LDO1 regulator driver, which is unexpected
behaviour of a regulator and not compatible with using an external
regulator.  [Originally this was documented as a feature of the internal
LDO -- broonie]

This patch exports functions to handle the booster enable and
DCVDD voltage, with each relevant subsystem flagging whether it can
currently run without the booster. Note that these subsystems are
stateless and none of them are nestable, so there's no need for
reference counting, we only need a simple boolean for each subsystem
of whether their current condition could require the booster or will
allow us to turn the codec down to lower operating power.
Signed-off-by: NRichard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The SCRATCH registers are used by firmwares to hold diagnostic
information. Log this during shutdown to assist analysis and debug
of firmwares.
Signed-off-by: NRichard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The mixer core on the Arizona devices is powered up whenever any routing
is non-zero. This patch saves a little power and avoids a few difficult
corner cases (around the mixer core being powered whilst there is no
clock available), by using the autodisable mux functionality to only
write out the settings for the muxes when they are powered up.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The DSP control information contains various hints about the usage of
the control use these when handling the control.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Using uXX for little endian data, was triggering some warnings through
sparse:

sound/soc/codecs/wm_adsp.c:716:26: sparse: cast to restricted __le16
sound/soc/codecs/wm_adsp.c:736:23: sparse: cast to restricted __le16
sound/soc/codecs/wm_adsp.c:739:23: sparse: cast to restricted __le32

Correct this by changing the casts to use __leXX instead of uXX.
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

There are very few version 0 firmwares in the wild and at some point in
the future it would be nice to remove support for them from the driver,
as they require several work arounds to be present to create controls
properly.

This patch adds a depreciated warning if someone is using this file
format.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Version 2 of the firmware file format includes length fields for the
various strings associated with control creation, to reduce file size.
However this does increase the parsing complexity slightly. This patch
adds support for the revision of the file format.

This patch also adds a new naming scheme for controls created from rev 2
firmware files. This version of the file format is commonly used to
add multiple controls per algorithm per memory region and the old
control naming scheme would cause multiple controls to have the same
name in this case.. Note that the naming scheme for older firmware
versions is left intact to ensure backwards compatibility.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Revision one of the file format includes new algorithm and coefficient
blocks which provide additional information about the controls exported
by the firmware. This patch updates the processing to handle this
version of the file format. Note that whilst this version of the format
adds support for specifying a name for the control through the firmware
file this has not been used and to keep compatibility with existing
deployments no changes to the firmware control naming are made by this
patch.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

This is slightly logically better and avoids some unnecessary forward
declarations in the following refactoring.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The private field in wm_coeff_ctl is currently unused and given the
controls are entirely handled within the ADSP code it is not clear what
it would be used for in the future. Remove the field for now it can be
readded if it is ever required.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Tidy up the code a little by factoring out the creation of the algorithm
regions.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Physically reading and writing controls to/from the DSP are handled by
two low level functions (wm_coeff_{write|read}_control, these currently
take in a snd_kcontrol pointer but immediately pull out a wm_coeff_ctl
pointer from the private data. These functions don't handle the kcontrols
at all they just shuttle data to and from the chip and all the call
sites have a wm_coeff_ctl pointer available. This patch just passes the
wm_coeff_ctl pointer straight into these functions.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Now we only allocate 44 bytes for the control name keep it on the stack
to avoid a lot of pointless memory allocation.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

ALSA only supports control names up to 44 bytes, so there is no point
allocating a whole page of memory to hold the control name, just limit
the control name to 44 bytes.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The algorithm region information in the firmware doesn't contain a
length field, explicitly pass this to the create_control function rather
than bundling into wm_adsp_alg_region.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

We have wm_adsp_region, wm_adsp_alg_region, and wmfw_region, the
variables for which are all frequently called region, this can get quite
confusing when reviewing the code especially given some functions are
quite long. Consistently use mem for wm_adsp_regions, alg_region for
wm_adsp_alg_region and region for wmfw_region.

Additionally, we use a mix of adsp and dsp for pointers to the wm_adsp
structure standardise this on dsp.

Finally, we use algs to refer to the number of algorithms quite
frequently, change this to the more descriptive n_algs.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The vast majority of the wm_adsp_setup_algs function is case statements
for ADSP1 or ADSP2, this patch splits this out into two separate
functions wm_adsp1_setup_algs and wm_adsp2_setup_algs. The small amount
of shared code between them is factored out into an extra helper
function. This makes the code a lot cleaner.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Now that the kernel provides DIV_ROUND_CLOSEST_ULL(), drop the internal
implementation and use the kernel one.
Signed-off-by: NJavi Merino <javi.merino@arm.com>
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Cc: Peter Rosin <peda@axentia.se>
Acked-by: NMark Brown <broonie@kernel.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently GPIO4 is hardcoded to output the pll-lock signal.
Unfortunately this is after the pll-out GPIO is configured which
is selectable in the device tree. Therefore it is not possible to
use GPIO4 for pll-out. Therefore this patch removes the
configuration of GPIO4.
Signed-off-by: NHoward Mitchell <hm@hmbedded.co.uk>
Signed-off-by: NMark Brown <broonie@kernel.org>

ak4642 doesn't have Mono record, ak4643 have it, but not supported.
This patch fixes channel mismatch
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

RT286 can't do register reset. If the hardware power is still existing
in power off, rt286 will keep the register settings. So, we need to
restore the default register value in probe to make sure the cache value
is the same as the real register value.
Signed-off-by: NBard Liao <bardliao@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Currently both the oscillator and the PLL are powered up in
set_bias_level. This can be problematic when using output clocks from
the wm8804 for other devices. The snd_soc_codec_set_pll API defines that
a clock should be available once the call returns, however, with all the
clocking controlled in set_bias_level this is not currently the case.

This patch enables pm_runtime for the wm8804, enabling both the
regulators and the oscillator when the chip resumes, and enabling the
PLL in the snd_soc_codec_set_pll call. Naturally the enabling the PLL
will also cause the chip to resume.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

This change converts the driver to use DAPM to control the power for the
various blocks on the chip. As part of this change the existing controls
"TX Playback Switch" (controlled power for the SPDIF TX block) and "AIF
Playback Switch" (controlled power for the AIF block) are both removed,
as they are now redundant since the power state of those blocks is
controlled automatically by DAPM.

There are several benefits of this change, the most important of which
is this change adds support for powering down the SPDIF RX block. The RX
block will automatically assume control of the PLL on the chip when it
is receiving a signal, so leaving this enabled all the time as was
currently done in the driver can be problematic. An incoming SPDIF signal
that is not being used can completely destroy the clocking for an in use
TX signal. But this change ensures that the RX block will only be
powered when the user intends to be receiving data, thus avoiding this
issue.

Additional benefits include the chip being simpler to operate as the
power no longer needs to be manually controlled between use-cases and a
small power saving (although it is acknowledged that this is likely
unimportant in the typical use-cases for this chip).
Signed-off-by: NSapthagiri Baratam <sapthagiri.baratam@incubesol.com>
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

To fix pop noise when shutdown,the pop noise during shutdown
is the pmic cutoff power of codec without any notice.
Signed-off-by: jay.xu <xjq@rock-chips.com>
Signed-off-by: Nzhengxing <zhengxing@rock-chips.com>
Signed-off-by: NCaesar Wang <wxt@rock-chips.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

It is best to use the physical reset if it is available. This patch adds
support for a GPIO controlled physical reset for the chip.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The earpiece on wm5102 is mono, thus there is no output 3R. Don't toggle
the volume update bits for this output, although worth noting that doing
so had no negative effects it is just redundant.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The delay time after a reset in the codec probe callback was too short,
and did not work on certain hw because the codec needs more time to
power on. This increases the delay time from 1us to 1ms.
Signed-off-by: NPascal Huerst <pascal.huerst@gmail.com>
Acked-by: NBrian Austin <brian.austin@cirrus.com>
Signed-off-by: NMark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

The wm8350 driver is the last driver that still uses the delayed_work field
from the snd_soc_dapm_context struct. Moving this over to the driver's
private data struct will allow us to remove the field from the DAPM context,
which will drastically reduce its size.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.

Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.

The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

When being powered on, either initially on probe or when resuming from
suspend, the wm8971 configures the device for quick output capacitor
charging. Since the charging can take a rather long time (up to multiple
seconds) it is done asynchronously without blocking. A delayed work item is
run once the charging is finished and the device is switched to the target
bias level.

This all done asynchronously to the regular DAPM sequence accessing the same
data structures and registers without any looking, which can lead to race
conditions. Furthermore this potentially delays the start of stream on the
CODEC while the rest of the system is already up and running, meaning the
first bytes of audio are lost. It also does no comply with the assumption of
the DAPM core that if set_bias_level() returned successfully the device will
be at the requested bias level.

This patch slightly refactors things and makes sure that the caps charging
is properly integrated into the DAPM sequence. When transitioning from
SND_SOC_BIAS_OFF to SND_SOC_BIAS_STANDBY the part will be put into fast
charging mode and a work item will be scheduled that puts it back into
standby charging once the charging period has elapsed. If a playback or
capture stream is started while charging is in progress the driver will now
wait in SND_SOC_BIAS_PREPARE until the charging is done. This makes sure
that charging is done asynchronously in the background when the chip is
idle, but at the same time makes sure that playback/capture is not started
before the charging is done.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.

Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.

The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

When being powered on, either initially on probe or when resuming from
suspend, the wm8971 configures the device for quick output capacitor
charging. Since the charging can take a rather long time (up to multiple
seconds) it is done asynchronously without blocking. A delayed work item is
run once the charging is finished and the device is switched to the target
bias level.

This all done asynchronously to the regular DAPM sequence accessing the same
data structures and registers without any looking, which can lead to race
conditions. Furthermore this potentially delays the start of stream on the
CODEC while the rest of the system is already up and running, meaning the
first bytes of audio are lost. It also does no comply with the assumption of
the DAPM core that if set_bias_level() returned successfully the device will
be at the requested bias level.

This patch slightly refactors things and makes sure that the caps charging
is properly integrated into the DAPM sequence. When transitioning from
SND_SOC_BIAS_OFF to SND_SOC_BIAS_STANDBY the part will be put into fast
charging mode and a work item will be scheduled that puts it back into
standby charging once the charging period has elapsed. If a playback or
capture stream is started while charging is in progress the driver will now
wait in SND_SOC_BIAS_PREPARE until the charging is done. This makes sure
that charging is done asynchronously in the background when the chip is
idle, but at the same time makes sure that playback/capture is not started
before the charging is done.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The delayed work used by the wm8971 driver to manage the caps charging
doesn't have any special requirements that would justify using a custom
workqueue, just use the generic system_power_efficient_wq instead.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Trivial typo fix.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Anish Kumar <Anish.Kumar@maximintegrated.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

This driver will set RT5645_DEPOP_MAN bit in headphone power up
depop process. We need to restore it in headphone power down
process. Otherwise, we will get headphone noise when push button
function is enabled.
Signed-off-by: NBard Liao <bardliao@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

In codec bias level off, we need to disable gate mode with MCLK
for power saving. It is set by one bit. We don't need to write
while register for that.
Signed-off-by: NBard Liao <bardliao@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

RT5645 doesn't support auto incrementing writes so driver should set
the use_single_rw flag for regmap.
Signed-off-by: NBard Liao <bardliao@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>