Add integrated IR subdevice interrupt and notification handling.  This is in
preparation of input keypress handling changes for the cx23885 module.
Signed-off-by: NAndy Walls <awalls@radix.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This change adds a skeletal implementation of a v4l2_subdevice to provide
encapsulation and abstraction of the CX23888's integrated consumer infrared
controller.  This change also instantiates the cx23888_ir subdev for the
HVR-1850 which has IR hardware physically wired up to a CX23888.

The cx23888_ir subdev code is being written with long-term objectives to:
1. port it to the cx25840 module for the CX2584x, CX2583x, CX23885, & CX231xx
   IR controllers
2. possibly port it to the cx18 module for the CX23418 IR controller
3. have the IR subdevice accessed abstractly in the cx23885 module, so the
   driver can ignore the difference between the CX23885 and CX23888.
Signed-off-by: NAndy Walls <awalls@radix.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The card uses the same cx23885 gpio lines for two adapters.
In case of there is several cards in system we must implement
gpio mutex per cx23885 chip.
Signed-off-by: NAbylay Ospan <aospan@netup.ru>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

cx23885: Modify hardware revision detection for newer silicon
Signed-off-by: NSteven Toth <stoth@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The encoder driver has hardcoded GPIO bits set for the HVR1800, regardless
of whether it's being used by a HVR1800 or not. I've implemented some generic
GPIO manipulation routines and I'm calling them only when appropriate.
Signed-off-by: NSteven Toth <stoth@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The GPIO's on the product can be in one of three places. To date we've
mainly used the GPIO's on the bridge itself, and once on the encoder.
Rather than having the complexity of multiple GPIO writes/reads from
isolated placed in the driver we'll route them through this function,
so we can make intelligent decisions about 1) Where the GPIO lives
and 2) Whether it conflicts (based on board) with some other function
to avoid bugs.
Signed-off-by: NSteven Toth <stoth@kernellabs.com>
Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

cx23885: Don't assume GPIO interrupts are cam related.
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

s_standby is only used to put the tuner in powersaving mode, so move it
from core to tuner.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Convert this driver to v4l2_subdev. Note that currently the only card with
analog support in this driver is the HVR-1800. The analog tuner support in
this driver is limited to what is needed for this board. When analog support
is added for other cards, then the tuner load code will probably have to be
expanded to take care of those boards. For example, there is currently no
support for either radio tuners or tda9887 demods.

I'd like to thank Steven Toth for testing this on his HVR-1800.
Tested-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The new support for the CX23885_BOARD_NETUP_DUAL_DVBS2_CI board broke the
existing boards. Interrupts for the netup part were enabled and handled
without testing whether the current board actually had a netup -> instant
and fatal crash.

I've added tests to do this only for the CX23885_BOARD_NETUP_DUAL_DVBS2_CI
board.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add support for NetUP Dual DVB-S2 CI card
The card based on cx23885 PCI-e bridge, CiMax SP2 Common Interface chips,
STM lnbh24 LNB power chip, stv6110 tuners and stv0900 demodulator.
http://www.linuxtv.org/wiki/index.php/NetUP_Dual_DVB_S2_CISigned-off-by: NIgor M. Liplianin <liplianin@netup.ru>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

To optimise data storage redundant vars are removed.
Signed-off-by: NDarron Broad <darron@kewl.org>
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

cx23885: Checkpatch compliance
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This allows some cardcoded functions to be more flexible, and paves
the way for any future cards that may have MFE support. Better to add it
now when the MFE patches is fresh in peoples mind, rather than 12 months
from now when new cards appear.
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Bug: the tree generated an oops when the cx23885 was laoded. This avoids
the oops by ensuring the mutex is correctly initialised before it's used.
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

v4l: replace __FUNCTION__ with __func__
Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

I need this so I can better isolate my linux email from my
corporate email.
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

In a previous patch I merged both memory maps into a single struct, believing
that they could be combined. We've since found problems with streaming
multiple channels on the 885. I'm restoring the multiple memory map structs
- in line with the windows driver.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This may be cx23885 chip specific and may not work on the cx23887.
Analog and mpeg encoder streaming are still to be tested.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Don't display the register when it's not appropriate for the specific port.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Certain DVB cards that have demodulators on TS1/VIDB were not streaming packets.
This ensure the pin directions on PAD_CTRL are set correctly, solving the issue.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

PAD_CTRL controls TS1 and TS2 input and output states, if the register
became corrupt the driver was never able to recover.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

With the HVR1800, trying to use video0 and video1 simultaneously caused
buffer corruption in the PCIe bridge. This fix reallocates video1
buffer locations to avoid the issue.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

cx23885: Enable cx23417 support on the HVR1800
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

cx23885: Add generic cx23417 hardware encoder support.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

For boards that require the avcore (cx25840) to be active, ensure
it gets loaded.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The dev element of the struct videobuf_queue is now of type struct device
implicitly. Fix left-over casts.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Reviewed-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This reduces the memory footprint and removes the need to
manually configure each map, which lead to a bug where
the Fusion EXP 5 board broke for a while.
This also fixes digital support again for
the DViCO FusionHDTV5Express.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Added missing do { } while (0)
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This enabled basic preview NTSC and PAL support for the HVR1800.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The cx23885/6/8 all have different clock rates, this patch allows
the core to compensate, and developers to allow vendor specific
overrides. This patches will be used by future analog video
and encoder patches.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

We need to clear space large enough for the video and encoder fifos.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Each version of the cx23885/7/8 silicon has different build revs.
We'll use this internal revision to work around bugs and known
issues in the video and encoder related patches.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

s/STATE_NEEDS_INIT/VIDEOBUF_NEEDS_INIT/g
s/STATE_PREPARED/VIDEOBUF_PREPARED/g
s/STATE_QUEUED/VIDEOBUF_QUEUED/g
s/STATE_ACTIVE/VIDEOBUF_ACTIVE/g
s/STATE_DONE/VIDEOBUF_DONE/g
s/STATE_ERROR/VIDEOBUF_ERROR/g
s/STATE_IDLE/VIDEOBUF_IDLE/g
Signed-off-by: NBrandon Philips <bphilips@suse.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch contains the following cleanups:
- make the following needlessly global code static:
  - cx23885-core.c: struct cx23885_sram_channels[]
  - cx23885-core.c: struct cx23887_sram_channels[]
  - cx23885-core.c: cx23885_wakeup()
  - cx23885-core.c: cx23885_sram_channel_setup()
  - cx23885-core.c: cx23885_sram_channel_dump()
  - cx23885-core.c: cx23885_risc_disasm()
  - cx23885-core.c: cx23885_shutdown()
  - cx23885-core.c: cx23885_reset()
  - cx23885-core.c: cx23885_dev_unregister()
  - cx23885-core.c: cx23885_risc_databuffer()
  - cx23885-core.c: cx23885_risc_stopper()
- #if 0 the following unused functions:
  - cx23885-core.c: cx23885_risc_buffer()
  - cx23885-core.c: cx23885_cancel_buffers()
- remove the following unused EXPORT_SYMBOL's:
  - cx23885-cards.c: cx23885_boards
  - cx23885-i2c.c: cx23885_call_i2c_clients
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Reviewed-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>