When linking multiple encoders to a connector, make sure
to not link LVDS with another connector.  Some bioses
have the same i2c line for LVDS and VGA.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

we were just using 1 before.

reported on irc by soreau
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Supported on all AVIVO-based asics.
Can be disabled via the new_pll module parameter:
new_pll=0 - disable
new_pll=1 - enable
enabled by default

[airlied: fixed to use do_div]
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@linux.ie>

Entries in the i2c table aren't always ordered
by id.  This allows us to remove some quirks
that are no longer needed.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

entries in the ss table aren't always ordered
by id.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This populates the connectors with HPD (Hot Plug Detect)
information.  This will be used in subsequent patches
for automatic digital monitor connect/disconnect handling.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

- keep the atom i2c id in the i2c rec
- fix gpio regs for GPIO and MDGPIO on pre-avivo chips
- track whether the i2c line is hw capable
- track whether the i2c line uses the multimedia i2c block
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This is enough to retrieve EDID and DPCP.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Similiar to other quirks for RV515, this card has no second DVI port.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Board is DVI+VGA, not DVI+DVI
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

sync polarity, etc.  This will likely fix LVDS problems
on some laptops.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

DVI-I port is actually DVI-D
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

- Change reg/mask names to match what we use internally
and in the bios
- Clarify how i2c over gpio on radeon actually works
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This will be useful for mode validation and certain
atom tables.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Lots of cases were wrong or missing.

v2: rebased against drm-next
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Limiting the pll output range is a good thing generally as
it limits the number of possible pll combinations for a given
frequency presumably to the ones that work best on each card.
That's why the limits are in the bios tables. However, certain
duallink DVI monitors seem to like pll combinations that would
be limited by this at least on pre-DCE 3.0 r6xx hardware.  This
might need to be adjusted per family or per clock range in the
future.

See fdo bug 24727.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Spread spectrum is a periodic disturbance added
to the feedback divider to change the pixel clock
periodically to reduce interference.

Only enabled on LVDS.

v2: add support for r4xx and fix DCE 3
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Where supported use ulMinPixelClockPLL_Output rather than
usMinPixelClockPLL_Output for pll_out_min.  This seems to
improve pll selection on some boards.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This reduces the number of mode format conversions needed
and makes native panel mode support cleaner.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

- clean up tv timing handling
- unify SetCRTC_Timing and SetCRTC_UsingDTDTiming
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

I never changed this back when I wrote tv-out support.
Signed-off-by: NDave Airlie <airlied@redhat.com>

This adds:
coherent mode: TMDS coherent mode for atom cards.
scaling mode: LVDS scaler mode
load detect: DAC load detection, DVI-I, VGA, TV
tmds pll: legacy TMDS pll selection
tv standard: TV standard selection.

for later: other TV ones? dvi subconnector selection using std prop

[contains fixes pointed out on dri-devel for atom bios mixups
 by Michel]
Signed-off-by: NDave Airlie <airlied@redhat.com>

[airlied:- adapted slightly in naming]
Signed-off-by: NYang Zhao <yang@yangman.ca>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@linux.ie>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This adds the r600 KMS + CS support to the Linux kernel.

The r600 TTM support is quite basic and still needs more
work esp around using interrupts, but the polled fencing
should work okay for now.

Also currently TTM is using memcpy to do VRAM moves,
the code is here to use a 3D blit to do this, but
isn't fully debugged yet.

Authors:
Alex Deucher <alexdeucher@gmail.com>
Dave Airlie <airlied@redhat.com>
Jerome Glisse <jglisse@redhat.com>
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This ports the tv-out code from the DDX to KMS.

adds a radeon.tv module option, radeon.tv=0 to disable tv
Signed-off-by: NDave Airlie <airlied@redhat.com>

The line mux for the connector in the bios tables
is used for enumerating drm connectors.  Since
this laptop has a quirk where the same line much is
listed for both VGA and LVDS, the connectors get
combined.  Setting the line mux on LVDS to an unused
value prevents both encoders from being combined into
the same connector.  This should fix bko bug 13720.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

just remove i variable left over from previous code.
Signed-off-by: NDave Airlie <airlied@redhat.com>

COMBIOS - fallback to table values if there are no tv dac or lvds bios tables
ATOMBIOS - add support for looking up these values from the bios table
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Add kernel modesetting support to radeon driver, use the ttm memory
manager to manage memory and DRM/GEM to provide userspace API.
In order to avoid backward compatibility issue and to allow clean
design and code the radeon kernel modesetting use different code path
than old radeon/drm driver.

When kernel modesetting is enabled the IOCTL of radeon/drm
driver are considered as invalid and an error message is printed
in the log and they return failure.

KMS enabled userspace will use new API to talk with the radeon/drm
driver. The new API provide functions to create/destroy/share/mmap
buffer object which are then managed by the kernel memory manager
(here TTM). In order to submit command to the GPU the userspace
provide a buffer holding the command stream, along this buffer
userspace have to provide a list of buffer object used by the
command stream. The kernel radeon driver will then place buffer
in GPU accessible memory and will update command stream to reflect
the position of the different buffers.

The kernel will also perform security check on command stream
provided by the user, we want to catch and forbid any illegal use
of the GPU such as DMA into random system memory or into memory
not owned by the process supplying the command stream. This part
of the code is still incomplete and this why we propose that patch
as a staging driver addition, future security might forbid current
experimental userspace to run.

This code support the following hardware : R1XX,R2XX,R3XX,R4XX,R5XX
(radeon up to X1950). Works is underway to provide support for R6XX,
R7XX and newer hardware (radeon from HD2XXX to HD4XXX).

Authors:
    Jerome Glisse <jglisse@redhat.com>
    Dave Airlie <airlied@redhat.com>
    Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>