Convert the existing uses of random_ether_addr to
the new eth_random_addr.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This stashes away this feature from standard kernel builds.
Signed-off-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Data pointer on rt2x00queue_for_each_entry() is never used - remove it.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Merge 3290 and 5390 POWER_BOUND and FREQ_OFFSET_BOUND defines.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix indention and remove unnecessary brackets and compares.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds an alternative tx status path
for BlockAck Requests as the hardware doesn't
recognize that a BlockAck Requests is usually
acked with a BlockAck and not a legacy ACK.

Without this patch, the stack would constantly
resent old and stale BARs. So, depending on the
receiver stack, this could lead to:

 - "stuck" ba sessions and package loss, as the
   stale BAR would reset the sequence each time.

 - lots of reorder releases.

 - ...
Reported-by: NSean Patrick Santos <quantheory@gmail.com>
Reported-by: NMikołaj Kuligowski <mikolaj.q@wp.pl>
Reported-by: NPer-Erik Westerberg <per-erik.westerberg@bredband.net>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Import new headers from my firmware branch:
<https://github.com/chunkeey/carl9170fw>

visit our wiki at:
<http://wireless.kernel.org/en/users/Drivers/carl9170.fw>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove the CONT_* and LNA_* messages from
AR_MCI_INTERRUPT_RX_MSG_DEFAULT. Those MCI rx messages only
meant for debugging purpose. Including them in default rx_msg
series could raise huge amount of MCI interrupts when BT traffic
is going on. And also it increases power consumption when WLAN
is scanning.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some code in write_{radio,radio}_reg() should just be run if this is a
pci based device. Add the condition again which was removed in commit:
commit 821e4e93
Author: Roland Vossen <rvossen@broadcom.com>
Date:   Mon Aug 8 15:58:58 2011 +0200

    staging: brcm80211: removed unused bus code from softmac
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts a unintended change mad in commit.
commit 4b006b11
Author: Arend van Spriel <arend@broadcom.com>
Date:   Thu Dec 8 15:06:54 2011 -0800

    brcm80211: smac: use bcma functions for register access in phy code
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Now brcms_c_chipmatch() is also able to handle non PCI devices and also
does some checking for SoC if they are supported by brcmsmac.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These extra offsets are only needed by PCIe devices and not when
running on an SoC.

This partly reverts commit:
commit 821e4e93
Author: Roland Vossen <rvossen@broadcom.com>
Date:   Mon Aug 8 15:58:58 2011 +0200

    staging: brcm80211: removed unused bus code from softmac
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The xmtfifo_sz array contains the queue sizes for the different core
revs. This array missed the sizes for the core rev 17 and 28. This
patch extends the array to also include these sizes and adds a warning
if no queue size is stored in the array for the given core rev.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds some workarounds for the BCM4716, BCM47162, BCM5357 to the
phy code again. This patch reverts parts of the following patch.

commit c2c72497
Author: Arend van Spriel <arend@broadcom.com>
Date:   Wed Jun 29 16:46:35 2011 -0700

    staging: brcm80211: remove unsupported chipset code from brcmsmac phy

The BCM4716 is working for me with an other firmware and I am working
on adding support for the other chips.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts some changes made in this commit:
commit 72345923
Author: Roland Vossen <rvossen@broadcom.com>
Date:   Mon Feb 14 12:16:45 2011 +0100

    staging: brcm80211: removal of inactive d11 code

The bcm4716 has a rev 17 wireless core and this condition is needed.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch depends on addin the chip IDs to bcma done in this commit in
my pending patch series for bcma.
Author: Hauke Mehrtens <hauke@hauke-m.de>
Date:   Sun Jun 3 18:17:57 2012 +0200

    bcma: add constants for chip ids
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch depends on adding the IDs to bcma done in
this commit in my pending patch series for bcma.
Author: Hauke Mehrtens <hauke@hauke-m.de>
Date:   Sun Jun 3 18:17:57 2012 +0200

    bcma: add constants for chip ids
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The removed workarounds are already performed in bcma_pmu_workarounds()
and bcma_core_chipcommon_init()

This patch depends on the completion of the workarounds in bcma done in
this commit in my pending patch series for bcma.
Author: Hauke Mehrtens <hauke@hauke-m.de>
Date:   Mon Jun 4 00:20:26 2012 +0200

    bcma: complete workaround for BCMA43224 and BCM4313
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

si_pmu_spuravoid_pllupdate() is now replaced by
bcma_pmu_spuravoid_pllupdate() which does the same thing, but supports
more chips.

This function is in my pending patch series for bcma.
Author: Hauke Mehrtens <hauke@hauke-m.de>
Date:   Mon Jun 4 01:31:32 2012 +0200

    bcma: add bcma_pmu_spuravoid_pllupdate()
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is already done by bcma_pmu_init() and bcma_pmu_resources_init() in bcma.
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

bcma also stores a pointer to the chipcommon core in its struct,
brcmsmac should use it and not search for the core by its own.
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Now "struct si_pub pub" does not have to be the first member in struct
si_info any more, if it is the resulting code after compilation should
be the same.
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These two functions are not used any more.
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The BCM4716 is a SoC and does not have a PCI client interface, so this
condition is never true.
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of checking if there is a PCIe core on the bus, better check if
hosttype is PCIe.

In the original submission to staging PCIE() checked, if the bustype is
PCI and the buscore is a PCIe core. Now we assume that all cores bcma
supports are PCIe based, so we just have to check if the bustype is PCI.

The old code bcmsmac currently uses searches for a PCIe core on the bus
and if there is one assumes that this is the buscore, which is wrong.
Some SoCs have a PCIe core operating in host mode and this is not the
bus core. The old code also caused a null pointer in
ai_get_buscoretype() and ai_get_buscorerev() if buscore was not set
because there was no PCIe core on the bus.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This hardware never became available to normal humans.  Leaving this
driver imposes unwelcome maintenance costs for no clear benefit.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>

We should free "chunk" here before returning the error code.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Don't use the ht_mode module parameter for determining AP supported
rates. We can rely on channel type, since HT40 won't be enabled if our
HT cap doesn't support it.

Enable MIMO only if there enough antennas, and rely on per-peer rate
limitation to prevent IOPs.
Signed-off-by: NArik Nemtsov <arik@wizery.com>

commit 587cc286 ("wlcore: compare ssid_len before comparing
ssids") introduced a new bug - the ssid length from the
request struct was compared against the ssid length of
another request, instead the one of the cmd.

This might cause the sched scan request to fail
(with -EINVAL) in many cases.
Signed-off-by: NEliad Peller <eliad@wizery.com>

It seems some parties have bad user experience when smaller values
are used. This should have little implications for power consumption,
since traffic is bursty in nature.
Signed-off-by: NArik Nemtsov <arik@wizery.com>

Avoid using the IEEE80211_NUM_BANDS constant for arrays sizes etc, as
this can contain bands unsupported by the driver (e.g. 60Ghz). Use an
internal constant to determine the number of bands.
Signed-off-by: NArik Nemtsov <arik@wizery.com>

If some IO read/write fails while the FW is not loaded, a recovery
will not take place. This means the SDIO_FAILED flag will stay in place
forever and prevent further read/writes.

This can happen if a check for STATE_OFF was forgotten in some routine.

Take this opportunity to rename the flag to IO_FAILED, since we support
other buses as well.
Reported-by: NIdo Yariv <ido@wizery.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>

wlcore needs to wait for certain events for example
for roc complete event. Usually the events are received
from the FW very fast, therefore wlcore can poll with
a short delay and if after a second the event was
not received yet poll with a long (1-5 msec) delay.

This implementation is similar to the sending of
commands to the FW.

Empirically the change reduced the wait for roc event
from ~10-40msec to 100s of usecs.

[replace udelay/msleep with usleep_range - Arik]
Signed-off-by: NYoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>

The interrupt line is disabled in op_stop using disable_irq. Since
pending interrupts are synchronized, the mutex has to be released before
disabling the interrupt to avoid a deadlock with the interrupt handler.

In addition, the internal state of the driver is only set to 'off'
after the interrupt is disabled. Otherwise, if an interrupt fires after
the state is set but before the interrupt line is disabled, the
interrupt handler will not be able to acknowledge the interrupt
resulting in an interrupt storm.

The driver's operations might be called during recovery. If these
acquire the mutex after it was released by op_stop, but before the
driver's state is changed, they may queue new work items instead of just
failing. This is especially problematic in the case of scans, in which a
new scan may be scheduled after all scan requests were cancelled.
Signed-off-by: NIdo Yariv <ido@wizery.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>

implement the .flush() callback by simply calling wl1271_tx_flush().
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

We have some API changes and new features in the new firmwares that
are not compatible with older drivers.  Increase the version of the FW
filenames for wl12xx to 5.

Additionally, remove the duplicate definitions from wlcore_i.h and
remove the MODULE_FIRMWARE macro calls from the SDIO and SPI modules,
since they're irrelevant there.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The driver configures the firmware template for probe requests during
the scan process.  If the same template is used for one-shot and sched
scans they will override each other when running scans simultaneously.

This fix works only on firmwares later than X.3.9.2.112 for single
role and X.3.9.2.23 for multi-role.

[Some cleaning-up and renaming of the quirk to something smaller --
Luca.]
Signed-off-by: NYoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

If recovery is called when the FW is off, we should clear the recovery
flag. Otherwise we risk booting the driver in permanent pending-recovery
state.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Don't read the FW panic log or print other debug data when recovery is
intended (i.e. FW type switch). This takes valuable time and can be
confusing to the user.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>