The noise and mic mixer inputs were not connected, do so.
Signed-off-by: NMark Brown <broonie@linaro.org>

The routes linking the widget and the input mux were being added
manually, rather than by the ARIZONA_MUX_ROUTES macro. This patchs adds
the routes to the macro.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

The input OSR bits are specified differently for wm5110 than for current
revs of wm5102. This patch corrects support for this on wm5110.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

When doing signal activity detection, the only output from the DRC will
often be a GPIO pin. This patch adds a signal activity output that is
activated when a GPIO is configured to output the DRC signal activity
detection.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

All sources and sinks should enable SYSCLK.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

Add callback to initialise the speaker in the core following the recent
changes to handling of integration with the thermal interrupts.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Running HPDET while the headphone outputs are enabled can disrupt the
operation of HPDET. In order to avoid this HPDET needs to disable the
headphone outputs and ASoC needs to not enable them while HPDET is
running.

Do the ASoC side of this by storing the enable state in the core driver
structure and only writing to the device if a flag indicating that the
accessory detection side is in a state where it can have the headphone
output stage enabled.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Some system designs have been identified which repurpose portions of the
speaker driver circuits for other functions which will require that they
not be managed using DAPM. Prepare for this by factoring out the creation
of the speaker widgets into the core driver, the widgets will be replaced
by dummy ones when the additional functions are enabled.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Since we are automatically managing the mutes we may as well also manage
the volume update bits, disabling volume updates while none of the inputs
are active. Since we are doing this we may as well allow the volumes to
ramp together so only enable volume updates once at the end of power up.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch allows the REFCLK to be set directly allowing much greater
flexibility in how the FLLs are configured.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

For optimal performance the inputs should be kept muted until after power
up. Since there are few use cases for muting inputs during capture move
the mutes to automatic control.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The generated defines in the header are pre-shifted.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The references used for the noise gates and parameters for their triggering
are configurable, expose that to users.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Though the controls are named as stereo controls in the part the main use
case for the analogue inputs to the WM5102 is mono. Reflect this in the
controls exposed to userspace, providing a series of mono controls rather
than stereo ones.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Provide a haptics widget for use by the haptics driver and expose the DAPM
context for it.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

There is no mixer attached to the ASRC on the wm5110 only a multiplexer
to select the source for the single input line. This change correctly
defines this in the wm5110 CODEC driver.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The volume update bits were being set on all but one input and one output.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The third output on WM5110 is a general purpose headphone output which can
be used to drive an earpice rather than a dedicated earpiece driver.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This will be used to enable additional control of the regulators.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The WM5110 is a highly integrated low power audio subsystem for
smartphones, tablets and other portable audio devices. It combines
an advanced DSP feature set with a flexible, high performance audio
hub CODEC.

This patch adds the audio CODEC driver for the device.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Some Arizona chips have a higher frequency for the FLL VCO, support this
in the common code.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The analogue PGA shifts were used; this makes no practical difference as
the values are the same.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This enables common telephony use cases.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Allow the user to select which of the system clocks each AIF is referenced
to and constran the DAI to the set of frequencies which can be generated
from that clock.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The WM5102 is a highly-integrated low-power audio system for smartphones,
tablets and other portable audio devices based on the Arizona platform.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>