For codec conexant 5045, I found that the name of 'Capture Source Items'
is different from the name of mixer.
The mixer is:
HDA_CODEC_VOLUME('Ext Mic Playback Volume', 0x17, 0x2, HDA_INPUT),
HDA_CODEC_MUTE('Ext Mic Playback Switch', 0x17, 0x2, HDA_INPUT),
But the capture source item is :
static struct hda_input_mux cxt5045_capture_source = {
	.num_items = 2,
	.items = {
		{ 'IntMic', 0x1 },
		{ 'LineIn', 0x2 },
	}
};
I think that it's better to change the name of capture_source to avoid
misunderstanding.
Signed-off-by: NJiang zhe <zhe.jiang@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

The benq r55e laptop have 3 jacks on the front panel.
One for HP, one for Line In and one for Mic In.
This patch implemented a new model to support it.
Signed-off-by: NJiang Zhe <zhe.jiang@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Signed-off-by: NJulian Scheel <julian@jusst.de>
Signed-off-by: NKonstantin Kletschke <konsti@ku-gbr.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Add proper register bit symbols for the I2S format field, and allow card
models to configure the I2S format to be used for the DACs and ADCs.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

See ALSA bug#1846 for more details.
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

See ALSA bug#2384 for more details.
Signed-off-by: NJulian Scheel <julian@jusst.de>
Signed-off-by: NKonstantin Kletschke <konsti@ku-gbr.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Codec with id 11c1:1040 sitting on hda bus isn't si3054-compatible.
It should be removed from patch_si3054.c id list.
The detailed information
	http://archives.linmodems.org/26457
From: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Some machines with STAC codecs seem to have problems (e.g. no audible
playback) when the delay in codec-read routine is too short.
I still don't figure out which command sequence causes this problem
(due to lack of test hardware), but it's known that increasing the
delay fixes.  So, added a stupid workaround here temporarily...
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

This device has io_type == 1 (Multiface) and firmware_rev > 0xa
(fixes regression from changeset 5326)
Signed-off-by: NAndreas Degert <ad@papyrus-gmbh.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Fix section mismatch in hdsp:  snd_hdsp_proc_init() can be called from
an ioctl at any time.
WARNING: vmlinux.o(.text+0x1089bc2): Section mismatch: reference to .init.text: (between 'snd_hdsp_create_alsa_devices' and 'snd_hdsp_free')
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Fix section mismatch in atiixp by making some functions __devinit.
WARNING: vmlinux.o(.text+0xfd9304): Section mismatch: reference to .init.data:atiixp_quirks (between 'ac97_probing_bugs' and 'snd_atiixp_codec_detect')
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Fix section mismatch in ad1889 by renaming the pci_driver variable to a
whitelisted variable name.
WARNING: vmlinux.o(.data+0x2e5ff0): Section mismatch: reference to .init.text:snd_ad1889_probe (between 'ad1889_pci' and 'index')
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Add a callback to the model structure to allow modification of the
hardware PCM limits.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Allow the models to modify mixer controls before they are added to the
card.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Allow the card models to specify whether each of the hardware DMA
channels is used.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Add a field to the model structure so that it is possible to have a card
where the SPI outputs 4 and 5 are used for an EEPROM.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Only initialize and create mixer controls for the first AC97 codec when
one has actually been detected.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Enable the SPDIF input-pin on VIA codecs when SPDIF-input is enabled
by BIOS.  Also, including a bit code clean up.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Added the support of Dell OEM laptops (Vostro 1200) with ALC268 codec.
The new model=dell is provided.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

It turned out that the PCBEEP element (0x1d) is disabled on some hardwares
although it's defined in the datasheet.  Because of the error at info of
this element, the mixer gets totally unusable.
Since the PCBEEP isn't that important feature, it's safer to disable this.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

There are two similar GPIO-enablement codes in patch_sigmatel.c.
Let's clean up.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

This patch removes hardcoded values for the number of streams supported
by the southbridge in most chipsets, and reads these values from the
chipset directly.  Most systems are hardwired for 4 streams in each
direction, but newer chipsets change that capability.
Signed-off-by: NTobin Davis <tdavis@dsl-only.net>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Rename the 'PCM Playback Volume'/'Switch' mixer controls to 'Master'.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

The line input cannot be mixed with the other inputs, so we have to mute
the other input switches when it is selected.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Use an array for the pointers to known controls so that it is easier to
add more.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Do not exchange the surround and back jacks except when in 7.1 mode
where the surround jack is not rear but side.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Removed 'FIXME' comments that have been already fixed.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

This patch fixes 5.1 surround output and headphone detection in the
Dell Inspiron 530 and possibly other Dell systems using the ALC888
codec (mode 6stack-dell).
Signed-off-by: NClaudio Matsuoka <cmatsuoka@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Fixes multiple device support by incrementing the static device counter
at the end of the azx_probe() call. Without this, subsequent probes would
always use the index specified for the first card.
Signed-off-by: NAndrew Paprocki <andrew@ishiboo.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

The ALC auto-probe creates mic boost controls automatically for the
probed pins, but it assumes that they are analog mics.  The digital
mics have no boost controls and must be skipped.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Print the name of the defect controls in error messages in amp info
callback.  This will make debugging easier.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Added a new STAC 9205 quirk for Vostro 1500.
Signed-off-by: NMatthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Added support for advanced power management support for output ports on
92HD7xxx family of codecs. Inactive output ports are powered down when
the pin sense  doesn't detect a connection, and powered back up when a
connection is sensed.
Signed-off-by: NMatthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Add master controls using vmaster to codecs that have no real hardware
master volume registers.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Added helper functions to implement virtual master volume controls.
The virtual master control is a control element that has multiple
slave controls.  The value of master element is equally added to
slave elements.
The functions are written for general purpose, but it's put in the
HD-audio directory as now, since HD-audio driver is the only user.
It should be moved to the common place once after other drivers use
vmaster.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Moved 2 systems PCI_QUIRK values to STAC_DELL_BIOS. Also the second
front HP jack is incorrect defined in the BIOS VT's for some laptops,
this patch corrects this.
Signed-off-by: NMatthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Please refer to the [0003680] on ALSA bugtracking system.
The user found that 'model=mbp3' works and provided the ID.
From: Jiang zhe <zhe.jiang@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

1. Support HP rp5700
2. Fixed alc_subsystem_id function (Bug fixed and support Desktop)
3. Support ASUS EP20
Signed-off-by: NKailang Yang <kailang@realtek.com.tw>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Added a mono output mute mixer for the 92hd71bxx family of codecs, this
also removes the need for the mono out node to explicitly unmuted in the
core init.
Signed-off-by: NMatthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

This header file exists only for some hacks to adapt alsa-driver
tree.  It's useless for building in the kernel.  Let's move a few
lines in it to sound/core.h and remove it.
With this patch, sound/driver.h isn't removed but has just a single
compile warning to include it.  This should be really killed in
future.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>