crt0.S had provisions to provide run address relocaton to got2 and
cache flush, but not on the bss clear or stack pointer load.  Apply
the same fixup for them.
Signed-off-by: NMilton Miller <miltonm@bga.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The ELF parsing routines local to arch/powerpc/boot/main.c are useful
to other callers therefore move them to their own file.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

72486f1f inverted the sense for enabling
hotplug CPU controls without reference to any other architecture other than
i386, ia64 and PowerPC.  This left everyone else without hotplug CPU control.

Fix powerpc for this brain damage.

(akpm: patch adapted from rmk's ARM fix.  Changelog stolen from rmk)
Signed-off-by: NGiuliano Pochini <pochini@shiny.it>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

dt_xlate_reg() uses the ranges properties of a node's parentage to find
the absolute physical address of the node's registers.

The ns16550 driver uses this when no virtual-reg property is found.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

There is no reason to yield the CPU in spu_yield - if the backing
thread reenters spu_run it gets added to the end of the runqueue for
it's priority.  So the yield is just a slowdown for the case where
we have higher priority contexts waiting.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

I wanted to enable CBE_THERM on PS3.  So I had to enable CBE_RAS first.

But the resulting kernel doesn't link, as cbe_regs.c isn't compiled for
non-PPC_CELL_NATIVE.

CBE_RAS should depend on PPC_CELL_NATIVE; this makes it so.
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This is now inaccurate because we may not have entered prom_init() and
r3 is overwritten immediately anyway.
Signed-off-by: NSonny Rao <sonny@burdell.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Remove unneeded inclusion of linux/ide.h
It does not compile with CONFIG_BLOCK=n.

Remove asm/ide.h from ksyms file, it gets included earlier via
linux/ide.h.

Compile tested with all defconfig files.
Signed-off-by: NOlaf Hering <olaf@aepfle.de>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Fix link errors with CONFIG_EEH=n:

arch/powerpc/platforms/built-in.o: In function `.pcibios_fixup_new_pci_devices':
(.text+0x41c8): undefined reference to `.eeh_add_device_tree_late'
arch/powerpc/platforms/built-in.o: In function `.init_phb_dynamic':
(.text+0x4280): undefined reference to `.eeh_add_device_tree_early'
arch/powerpc/platforms/built-in.o: In function `.pcibios_remove_pci_devices':
(.text+0x42fc): undefined reference to `.eeh_remove_bus_device'
arch/powerpc/platforms/built-in.o: In function `.pcibios_add_pci_devices':
(.text+0x43c0): undefined reference to `.eeh_add_device_tree_early'
arch/powerpc/platforms/built-in.o: In function `.pSeries_final_fixup':
(.init.text+0xb4): undefined reference to `.pci_addr_cache_build'
make[1]: *** [.tmp_vmlinux1] Error 1
Signed-off-by: NOlaf Hering <olaf@aepfle.de>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This cleans up how the zImage code manipulates the kernel
command line.  Notable improvements from the old handling:
	- Command line manipulation is consolidated into a new
prep_cmdline() function, rather than being scattered across start()
and some helper functions
	- Less stack space use: we use just a single global command
line buffer, which can be initialized by an external tool as before,
we no longer need another command line sized buffer on the stack.
	- Easier to support platforms whose firmware passes a
commandline, but not a device tree.  Platform code can now point new
loader_info fields to the firmware's command line, rather than having
to do early manipulation of the /chosen bootargs property which may
then be rewritten again by the core.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch adds a library of useful device tree manipulation functions
to the zImage library, for use by platform code.  These functions are
based on the hooks already in dt_ops, so they're not dependent on a
particular device tree implementation.  This patch also slightly
streamlines the code in main.c using these new functions.

This is a consolidation of my work in this area with Scott Wood's
patches to a very similar end.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

mtocrf is a faster single-field mtcrf (move to condition register
fields) instruction available in POWER4 and later processors.  It can
make quite a difference in performance on some implementations, so use
it for CONFIG_POWER4_ONLY builds.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

There are many adapters which cannot handle DMAing across any 4 GB
boundary.  For instance, the latest Emulex adapters.

This normally is not an issue as firmware gives dma-windows under
4gigs.  However, some of the new System-P boxes have dma-windows above
4gigs, and this present a problem.

During initialization of the IOMMU tables, the last entry at each 4GB
boundary is marked as used.  Thus no mappings can cross the boundary.
If a table ends at a 4GB boundary, the entry is not marked as used.

A boot option to remove this 4GB protection is given w/ protect4gb=off.
This exposes the potential issue for driver and hardware development
purposes.
Signed-off-by: NJake Moilanen <moilanen@austin.ibm.com>
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Adding this handler allow userspace to properly handle the module
autoloading. The generation of the uevent itself is now common to
all bus using of_device, so not much code here.
Signed-off-by: NSylvain Munaut <tnt@246tNt.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This common uevent handler allow the several bus types based on
of_device to generate the uevent properly and avoiding
code duplication.

This handlers take a struct device as argument and can therefore
be used as the uevent call directly if no special treatment is
needed for the bus.
Signed-off-by: NSylvain Munaut <tnt@246tNt.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The bit setting was off by one.
Tested with RTC and GPIO_WKUP interrupts.
Signed-off-by: NDomen Puncer <domen.puncer@telargo.com>
Signed-off-by: NSylvain Munaut <tnt@246tNt.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NXianghua Xiao <x.xiao@freescale.com>
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Signed-off-by: NYork Sun <yorksun@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NJon Loeliger <jdl@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This patch provides the basic MPC8544 DS platform code and config.
Follow-up patches will add peripherals such as PCI and SATA.
Signed-off-by: NXianghua Xiao <x.xiao@freescale.com>
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Signed-off-by: NYork Sun <yorksun@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NJon Loeliger <jdl@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add support for the MPC8323E Reference Development Board (RDB).  The board
is a mini-ITX reference board with 64M DDR2, 16M flash, USB, PCI,
10/100 ethernet, serial, and phone ports.
Signed-off-by: NMichael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Correct the alignment of the internal buffer used by the QUICC Engine
SDMA controller to 4Kbytes.  Correct the shift direction in the logic
that sets up the SDMR register for the QUICC Engine SDMA controller.
Signed-off-by: NChuck Meade <chuckmeade@mindspring.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Fix a bug in dcr_unmap().

At unmap time the DCR offset need to be added instead of substracted.
Signed-off-by: NJean-Christophe Dubois <jdubois@mc.com>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

mpc832x_mds.h was exporting a function that didn't exist anymore.  Once removed
the header had no purpose.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

In two places, ucc_slow_init() passes a physical address instead of the
virtual address to functions that were expecting the latter, causing a kernel
panic.  us_info->regs contains the physical address of the UCC register set.
The registers are ioremap'd to kernel space, and the virtual pointers are
stored in us_regs.  The code was using us_info->regs when it should have been
using us_regs.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

  Delete apparently unused header file
arch/powerpc/platforms/83xx/mpc834x_itx.h.
Signed-off-by: NRobert P. J. Day <rpjday@mindspring.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Change the Kconfig files so that the Freescale QE options are automatically
selected if a QE device is selected.  Previously, you'd need to manually
select UCC_FAST if you want any "fast" UCC devices, such as Gigabit Ethernet.
Now, the QE Gigabit Ethernet option is always available if the device has a
QE, and UCC_FAST is automatically enabled.  A side-effect is that the
"QE Options" menu no longer exists.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Unify PCI Express memory map registers structure define
to arch/pwoerpc/sysdev/fsl_pcie.h for Freescale 85xx/86xx
processor family.
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This move sets the stage for the use of generic PCI Express
code in 85xx and 86xx parts from FSL.  Subsequent patches
for 8548 and 8544 will be able to use this shared code.
Signed-off-by: NJon Loeliger <jdl@freescale.com>
Acked-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NZhang Wei <wei.zhang@freescale.com>
Signed-off-by: NJon Loeliger <jdl@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This patch adds a reg.h to the zImage code, with common definitions
for accessing system registers.  For now, this includes functions for
retrieving the PVR and the stack pointer.  This patch then uses the
new reg.h to let start() display the running stack address without
having to explicitly pass the stack as a parameter from the asm code.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch adds the correct attributes to the zImage's versions of
printf to make gcc generate format string mismatch warnings.  It also
corrects several minor problems with format strings in the zImage thus
discovered.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Before the plethora of platforms gets any worse, establish a common
rule to invoke the wrapper for any platform.  Add arguments to
the rule for initrd, dts, dtb, etc.   Show example usage with initrd.

Create default rules for zImage, and zImage.initrd.  initrd targets
depend on the ramdisk file.

Don't consider targets for zImage.initrd that are targets for zImage.
This means uImage is no longer considered a target for zImage.initrd.
Signed-off-by: NMilton Miller <miltonm@bga.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Now that obj-boot is in targets, we can remove (twice) it from clean-files.
zImage.initrd was missing, move zImage nearer where its used, and place
zImage.initrd next to it.  Remove non-ported zImage.sandpoint, and add
auto-generation of unconfigured zImage.initrd* like image-.
Signed-off-by: NMilton Miller <miltonm@bga.com>
--
Testing: did a few builds and cleans
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Kbuild if_changed and if_changed_dep require the use of the dummy
FORCE to get the dependencies right.   Also add to targets to get
correct behavior.
Signed-off-by: NMilton Miller <miltonm@bga.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Some platforms might need to run some code before the zImage start, but
could otherwise use the bss clear and relocation code.   Export the
start address strongly as zImage_start_lib.
Signed-off-by: NMilton Miller <miltonm@bga.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Add a macro fatal that calls printf then exit.  User must include stdio.h.

Typically replaces 3 lines with 1, although I added back some whitespace.
Signed-off-by: NMilton Miller <miltonm@bga.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This removes the time suspend/restore code that was done through
a PMU notifier in arch/platforms/powermac/time.c.

Instead, introduce arch/powerpc/sysdev/timer.c which creates a sys
device and handles time of day suspend/resume through that.

This should probably be replaced by using the generic RTC framework
but for now it gets rid of the arcane powermac specific hack.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Use lowercase for hex printouts in oops messages. The number of times I have
tried to copy and paste from an oops into an objdump search...
Signed-off-by: NAnton Blanchard <anton@samba.org>
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Looks like someone got this backwards, highlighting the perils of the
? : !!! :)
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Handle recursive oopses, like on x86. We had a few cases recently where
we locked up in oops printing and didnt make it into crashdump.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>