The previous change by Kumar Gala in this area led to legacy_serial.c
and udbg_16550.c being built as modules when CONFIG_SERIAL_8250=m.
Fix this by introducing a new symbol, CONFIG_PPC_UDBG_16550, to
control whether these files get built, and arrange for it to be selected
for those platforms that need it.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NAdrian Bunk <bunk@stusta.de>

In setup_arch and setup_system call find_legacy_serial_ports() if we
build in support for 8250 serial ports instead of basing it on PPC_MULTIPLATFORM.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

There's a few places where we need to fix things up for the kernel to work
if it's linked at 32MB:

 - platforms/powermac/smp.c
   To start secondary cpus on pmac we patch the reset vector, which is fine.
   Except if we're above 32MB we don't have enough bits for an absolute branch,
   it needs to relative.
 - kernel/head_64.s
    - A few branches in the cpu hold code need to load the full target address
      and do a bctr.
    - after_prom_start needs to load PHYSICAL_START as the dest address, not 0.
    - The exception prolog needs to load the low word of the target adddress,
      not just the low halfword.
    - Fixup handling of the initial stab address.
 - kernel/setup_64.c
   smp_release_cpus() needs to write 1 to the spinloop flag near 0, not 32 MB.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Regardless of where the kernel's linked we always get interrupts at low
addresses. This patch creates a trampoline in the first 3 pages of memory,
where interrupts land, and patches those addresses to jump into the real
kernel code at PHYSICAL_START.

We also need to reserve the trampoline code and a bit more in prom.c
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch adds a Kconfig variable, CONFIG_CRASH_DUMP, which configures the
built kernel for use as a Kdump kernel.

Currently "all" this involves is changing the value of KERNELBASE to 32 MB.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch unifies udbg for both ppc32 and ppc64 when building the
merged achitecture. xmon now has a single "back end". The powermac udbg
stuff gets enriched with some ADB capabilities and btext output. In
addition, the early_init callback is now called on ppc32 as well,
approx. in the same order as ppc64 regarding device-tree manipulations.
The init sequences of ppc32 and ppc64 are getting closer, I'll unify
them in a later patch.

For now, you can force udbg to the scc using "sccdbg" or to btext using
"btextdbg" on powermacs. I'll implement a cleaner way of forcing udbg
output to something else than the autodetected OF output device in a
later patch.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This moves the discovery of legacy serial ports to a separate file,
makes it common to ppc32 and ppc64, and reworks it to use the new OF
address translators to get to the ports early. This new version can also
detect some PCI serial cards using legacy chips and will probably match
those discovered port with the default console choice.

Only ppc64 gets udbg still yet, unifying udbg isn't finished yet.

It also adds some speed-probing code to udbg so that the default console
can come up at the same speed it was set to by the firmware.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Cache info is setup by walking the device tree in initialize_cache_info().
However, icache_flush_range might be called before that, in
slb_initialize()->patch_slb_encoding, which modifies the load immediate
instructions used with SLB fault code.

Not only that, but depending on memory layout, we might take SLB faults
during unflatten_device_tree. So that fault will load an SLB entry that
might not contain the right LLP flags for the segment.

Either we can walk the flattened device tree to setup cache info, or
we can pick the known defaults that are known to work. Doing it in the
flattened device tree is hairier since we need to know the machine type
to know what property to look for, etc, etc.

For now, it's just easier to go with the defaults. Worst thing that
happens from it is that we might waste a few cycles doing too small
dcbst/icbi increments.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The userspace kexec-tools need to know the location of the htab on non-lpar
machines, as well as the end of the kernel. Export via the device tree.

NB. This patch has been updated to use "linux,x" property names. You may
need to update your kexec-tools to match.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch moves the vdso's to arch/powerpc, adds support for the 32
bits vdso to the 32 bits kernel, rename systemcfg (finally !), and adds
some new (still untested) routines to both vdso's: clock_gettime() with
support for CLOCK_REALTIME and CLOCK_MONOTONIC, clock_getres() (same
clocks) and get_tbfreq() for glibc to retreive the timebase frequency.

Tom,Steve: The implementation of get_tbfreq() I've done for 32 bits
returns a long long (r3, r4) not a long. This is such that if we ever
add support for >4Ghz timebases on ppc32, the userland interface won't
have to change.

I have tested gettimeofday() using some glibc patches in both ppc32 and
ppc64 kernels using 32 bits userland (I haven't had a chance to test a
64 bits userland yet, but the implementation didn't change and was
tested earlier). I haven't tested yet the new functions.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This also make klimit have the same type on 32-bit as on 64-bit,
namely unsigned long, and defines and initializes it in one place.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch merges platform codes.  systemcfg->platform is no longer used,
systemcfg use in general is deprecated as much as possible (and renamed
_systemcfg before it gets completely moved elsewhere in a future patch),
_machine is now used on ppc64 along as ppc32.  Platform codes aren't gone
yet but we are getting a step closer. A bunch of asm code in head[_64].S
is also turned into C code.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

for functions defined by setup-common.c and used in setup_xx.c
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>

This factors out the common bits of arch/powerpc/xmon/start_*.c into
a new nonstdio.c, and removes some stuff that was supposed to make
xmon's I/O routines somewhat stdio-like but was never used.

It also makes the parsing of the xmon= command line option common,
so that ppc32 can now use xmon={off,on,early} also.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

OK, the Fedora ppc32 and ppc64 kernels should both be arch/powerpc by
tomorrow. They're booting on G5, POWER5, and my powerbook. I'll test
pmac SMP and Pegasos later -- but pmac smp is known broken in arch/ppc
anyway, and I'll live with a potential Pegasos regression for now; it
wasn't supported officially in FC4 either.

I needed to fix ppc32 initrd -- we were never setting initrd_start.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The ancient ppcdebug/PPCDBG mechanism is now only used in two places.
First, in the hash setup code, one of the bits allows the size of the
hash table to be reduced by a factor of 8 - which would be better
accomplished with a command line option for that purpose.  The other
was a bunch of bus walking related messages in the iSeries code, which
would seem to be insufficient reason to keep the mechanism.

This patch removes the last traces of this mechanism.

Built and booted on iSeries and pSeries POWER5 LPAR (ARCH=powerpc).
Signed-off-by: NDavid Gibson <dwg@au1.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Adds a new CONFIG_PPC_64K_PAGES which, when enabled, changes the kernel
base page size to 64K.  The resulting kernel still boots on any
hardware.  On current machines with 4K pages support only, the kernel
will maintain 16 "subpages" for each 64K page transparently.

Note that while real 64K capable HW has been tested, the current patch
will not enable it yet as such hardware is not released yet, and I'm
still verifying with the firmware architects the proper to get the
information from the newer hypervisors.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This also moves setup_cpu_maps to setup-common.c (calling it
smp_setup_cpu_maps) and uses it on both 32-bit and 64-bit.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

There's no reason for smp_release_cpus() to be asm, and most people can make
more sense of C code. Add an extern declaration to smp.h and remove the custom
one in machine_kexec.c
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>

Signed-off-by: NKelly Daly <kelly@au.ibm.com>

The official name for BPA is now CBEA (Cell Broadband
Engine Architecture). This patch renames all occurences
of the term BPA to 'Cell' for easier recognition.
Signed-off-by: NArnd Bergmann <arndb@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

By parsing the command line earlier, we can add the mem= value to the
flattened device tree and let the generic code sort out the memory limit
for us.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>

We had a static memory_limit in prom.c, and then another one defined
in setup_64.c and used in numa.c, which resulted in the kernel crashing
when mem=xxx was given on the command line.  This puts the declaration
in system.h and the definition in mem.c.  This also moves the
definition of tce_alloc_start/end out of setup_64.c.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The merged version follows the ppc64 version pretty closely mostly,
and in fact ARCH=ppc64 now uses the arch/powerpc/xmon version.
The main difference for ppc64 is that the 'p' command to call
show_state (which was always pretty dodgy) has been replaced by
the ppc32 'p' command, which calls a given procedure (so in fact
the old 'p' command behaviour can be achieved with 'p $show_state').
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This allows us to also use entry_64.S from the merged tree and reverts
the setup_64.c part of fda262b8.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>

With ARCH=powerpc we assume the presence of a device tree, so we don't
require any support for the old bi_recs method of passing boot
parameters.  Likewise, we've never needed it for ppc64, but we still
had an include/asm-ppc64/bootinfo.h from which nothing was used.  This
patch removes that file, and all references to it in arch/ppc64 and
arch/powerpc.  A related, unused variable 'boot_mem_size' is also
removed from setup_32.c.  The bootinfo stuff remains in ARCH=ppc for
the time being.

Built and booted on Power5 (ARCH=ppc64 and ARCH=powerpc), built for
32-bit powermac (ARCH=powerpc and ARCH=ppc).
Signed-off-by: NDavid Gibson <dwg@au1.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

and use setup_64.c from the merged tree instead.  The only difference
between them was the code to set up the syscall maps.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This should have been in commit 03501dab
but got missed by accident.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This way they get done in one place for all platforms, and it is
more consistent with what ppc32 does.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

... for consistency with ppc32; also add in ppc32's show_percpuinfo
function.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

We now use the merged time.c for both 32-bit and 64-bit compilation
with ARCH=powerpc, and for ARCH=ppc64, but not for ARCH=ppc32.
This removes setup_default_decr (folds its function into time_init)
and moves wakeup_decrementer into time.c.  This also makes an
asm-powerpc/rtc.h.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

A bunch of printks were left in arch/powerpc/kernel/setup_64.c from
when I was chasing a bug.  This removes them.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This is a bunch of mostly small fixes that are needed to get
ARCH=powerpc to compile for 64-bit.  This adds setup_64.c from
arch/ppc64/kernel/setup.c and locks.c from arch/ppc64/lib/locks.c.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Add /chosen/linux,platform to the device tree so we can remove iSeries
specific code in setup_system() to set systemcfg->platform.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>

Misc steps to incorporate the flat device tree on iSeries.

- define iseries_probe()
- call build_iSeries_Memory_Map() earlier
- return __pa() of the flat device tree from iSeries_early_setup()
- actually call early_setup() for iSeries
- add iseries_md to machdep_calls
- build prom.o for iSeries
- enable /proc/device-tree for iSeries
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>

We don't need to call smp_release_cpus() on iSeries but it's harmless
if we do and it removes another #ifdef ISERIES.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>

We don't need to call stab_initialize() for the boot cpu on iSeries, so
we hack around it so that early_setup() can be called on iSeries.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>

ppc64_attention_msg and ppc64_dump_msg are not used so remove them.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Rather than hard-coding the platform device IDs, enumerate them.
We don't particularly care about the actual ID we get, just as
long as they're unique.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>