This mutex is meant to stop two devices getting the same ID. dvbdev_get_free_id() 
scans the list of already allocated devices to find a free id.
Unfortunately, since the mutex is unlocked before the card is added to the
above list, it is still possible for two of them to get the same id.
Its debatable whether this mutex lock is actually needed, but I'm unwilling
to just remove it in case something does depend on it.
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Unfortunately on the budget-av board, the CAM reset line is tied to the
frontend reset line, so resetting the CAM also zaps the frontend. This
breaks the tda1004x at least, and causes it to fail to tune until the
budget-av module is reloaded. This patch adds an exported function to dvb_frontend
that allows a card to forcibly reinitialise a frontend. The budget-av now
does this on CAM reset, which corrects this problem.
since they do not tie the CAM reset line to the frontend reset line.
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The dvr device could be opened multiple times simultaneously in O_RDONLY mode.
Each open after the first would allocate a new dvr buffer (1880 KB) and leak
the old buffer.  The first close would de-allocate the dvr buffer and cause
all other open dvrs to stop working.  This patch allows only a single O_RDONLY
open of the drv device, as per the API specification.  Multiple O_WRONLY opens
are still allowed and don't appear to cause any problems.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This attached patch was originally proposed by Anssi Hannula to the dvb-kernel
user to choose the default broadcast mode when using the ttpci driver.
NTSC users need to only add the following line to modprobe.d:
options dvb-ttpci tv_standard=1 
PAL users will not need to change anything, for this will be the default.
Signed-off-by: NC.Y.M <syphir@syphir.sytes.net>
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch fixes a typo in a comment.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- Issue a warning when more than 80% of the DMA buffer is being used 
  (probably due to bad IRQ latency). Warnings are rate-limited.
- Introduce a new parameter 'bufsize' (in KByte) which increases the
  default DMA buffer of 188 KByte up to 1410 KByte (Activy: 564 KByte).
Signed-off-by: NIngo Schneider <mail@ingo-schneider.de>
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- Added firmware download comments to or51211 and or51132 Kconfig help text.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

There seems to be a new version of the USB DVB-T stick from WideView with a new demod-revision inside and thus a new firwmare.
This patch enables support for that.
Thanks to Mikel Martin for early testing.
Signed-off-by: NPatrick Boettcher <pb@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Thanks to: Andrew Cohen <cohen@andy.bu.edu>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- Added keycodes for the DViCO FusionHDTV portable remote control.
- Enabled the remote control for both versions of FusionHDTV DVB-T USB
  and the FusionHDTV 5 USB Gold (ATSC)
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The bt8xx drivers uses request_firmware()
and thus needs to select FW_LOADER.
Signed-off-by: Nmaximilian attems <maks@sternwelten.at>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Mark the f_ops members of inodes as const, as well as fix the
ripple-through this causes by places that copy this f_ops and then "do
stuff" with it.
Signed-off-by: NArjan van de Ven <arjan@infradead.org>
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add a new audio mode V4L2_TUNER_MODE_LANG1_LANG2 (used by VIDIOC_G/S_TUNER).
This mode allows the user to select both languages of a bilingual transmission,
one language on the left, one on the right audio channel. If there is no
bilingual transmission, or it is not supported, then this mode should act like
V4L2_TUNER_MODE_STEREO.
This mode is introduced for PVR-like drivers where it is useful to be able to
record both languages of a bilingual broadcast.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Only the Medion boxes return 0x08 after an i2c read/write.
The bluebird devices do not return anything at all.
This patch conditionalizes the test for the 0x08 return code
to produce a warning message when using the Medion box, only.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- corrects the wording in some of the debug messages.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Removed the FIXME comment from bluebird_patch_dvico_firmware_download:
 /* FIXME: are we allowed to change the fw-data ? */
Yes, we are allowed. DViCO's Windows driver also does the same thing.
A single firmware image is used to support all of the bluebird boxes.
The firmware sets all devices to PID: d700. Instead of using that, the
driver replaces the d700 with the cold PID+1 before the download.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch removes the (harmless) -ETIMEDOUT during device init
for the DViCO FusionHDTV Bluebird boxes, by conditionalizing the
gpio write inside cxusb_i2c_xfer to happen only for Medion boxes.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

There was no MODULE_DEVICE_TABLE for the b2c2-flexcop-usb module. This makes it
impossible for hotplug to load the module automatically, when such a device is
connected.
Signed-off-by: NPatrick Boettcher <pb@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NManu Abraham <manu@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This reverts commit 08f1d0b9

The "bt8xx/ conversion" for drivers/video/ hasn't actually percolated
all the way to this tree, so the Makefile change escaped too soon.

Build breakage noticed by Jeff Garzik <jeff@garzik.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NManu Abraham <manu@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Add wss_cfg_4_3 and wss_cfg_16_9 configuration options.
Firmware 2623 or later required.
Both parameters are bit masks:
- bit 15: disable WSS
- bit 14: send short WSS burst, then turn off WSS
- bit 13..0: WSS bits as specified by the standard
These parameters are useful if you own a broken tv set which
does not handle wss correctly.
Default settings:
- wss_cfg_4_3: 0x4008
- wss_cfg_16_9: 0x0007
These should work with most devices.
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Moved duplicated code of ALPS BSRU6 tuner to a standalone file.
Modified av7110 and budget drivers to include the new file.
Signed-off-by: NPerceval Anichini <perceval.anichini@streamvision.fr>
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- Corrected typo for NxtWave NXT200X
- Added "Oren" manufacturer name to menu items for OR51132 and OR51211
- Removed "(pcHDTV HDx000 card)" from Oren frontends menu item names,
  This isn't necessary, as these frontends are selected by the card drivers,
  build configuration (DVB_BT8XX and VIDEO_CX88_DVB).
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Detaching the device didn't clean up several device files in /dev/dvb,
after applying that patch all dvb devices disappeared as expected.
Signed-off-by: NMarkus Rechberger <mrechberger@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Use dvb_ringbuffer instead of an own buffer implementation in
dmxdev.[ch].
Signed-off-by: NAndreas Oberritter <obi@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Oliver Endriss spotted, that resetting read and write pointers on
flush() requires additional locking and breaks the av7110 driver.
Therefore this patch partially reverts the previous patch titled "make
dvb_ringbuffer compatible to dmxdev_buffer".
Signed-off-by: NAndreas Oberritter <obi@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NEric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Added variable 'error' to struct dvb_ringbuffer, which is set to zero on
init() and flush(). Also reset read an write pointers to zero on flush()
to get less fragmented data.
Signed-off-by: NAndreas Oberritter <obi@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Used Lindent, manually changed some line breaks. Removed invalid email
addresses, useless casts and useless initialization of return values.
Signed-off-by: NAndreas Oberritter <obi@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Rename 'enum dmxdevype' to 'enum dmxdev_type' and use this enum instead
of int for the member 'type' of struct dmxdev_filter.
Signed-off-by: NAndreas Oberritter <obi@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The member dvbdev gets initialized once but is never used after that.
Signed-off-by: NAndreas Oberritter <obi@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The PID value is already stored in struct dmx_sct_filter_params which is
a member of struct dmxdev_filter.
Acked-by: NJohannes Stezenbach <js@linuxtv.org>
Signed-off-by: NAndreas Oberritter <obi@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Typos grab bag of the month.
Eyeballed by jmc@ in OpenBSD.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Workaround for Nexus CA: Debi test fails unless first debi write is repeated.
Signed-off-by: NMarco Schluessler <marco@lordzodiac.de>
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Typos grab bag of the month.
Eyeballed by jmc@ in OpenBSD.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- The tuner used in DViCO FusionHDTV DVB-T hybrid is made by Thomson
- renamed tuner and dvb_pll structs accordingly
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Add support for the FE6600 tuner used on the DVB-T Hybrid board.
Add support for the Zarlink ZL10353 DVB-T demodulator, which supersedes the
MT352, used on the DViCO FusionHDTV DVB-T Hybrid and later model Plus boards.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>