Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 12 10月, 2007 16 次提交
    • B
      icside: fix ->speedproc to return on unsupported modes (take 5) · f44ae58a
      由 Bartlomiej Zolnierkiewicz 提交于 
      * All other implementations of ->speedproc return zero on success
  and non-zero on failure.  Currently it doesn't matter for icside host
  driver and isn't a bug per se since:

  - ide_set_xfer_rate() return value is ignored by all IDE core users

  - icside doesn't (yet!) use ide_tune_dma() in icside_dma_check()

  but sooner or later we will need to fix anyway - so lets do it now.

* icside_set_speed() happily accepts unsupported transfer modes which
  results in drive->drive_data being set to the maximum value (480)
  and drive->current_speed being set to the unsupported transfer mode.

  Fix it.

v2:
* The initial version of the patch was broken because it didn't take into
  the account (the different from usual) return values of icside_set_speed()
  (Noticed by Russell).

v3:
* Remove no longer needed initialization/checking of cycle_time
  (Noticed by Sergei).

* No need to set drive->drive_data if DMA is not going to be used
  (Noticed by Sergei).

* Remove incorrect setting of drive->current_speed
  (Noticed by Sergei).

* Move ide_config_drive_speed() at the end of icside_set_speed().

v4:
* If DMA mode is not found in icside_dma_check() then just return "-1" and
  don't call icside_set_speed() (v3 got it wrong and "1" was returned instead).

v5:
* Return "-1"/"0" in icside_set_speed() instead of icside_dma_check() return
  value (just like it was before this patch).

Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      f44ae58a
    • B
      sgiioc4: use ide_tune_dma() · ca1997c1
      由 Bartlomiej Zolnierkiewicz 提交于 
      * Add DRV_NAME define and use it instead of sgiioc4_chipset.name.

* Remove no longer needed sgiioc4_chipset.

* Remove needless clearing of ->atapi_dma from ide_dma_sgiioc4().

* Fix ide_dma_sgiioc4() to return success/failure.  Check return value in
  sgiioc4_ide_setup_pci_device() and set hwif->autodma accordingly.  Also add
  missing setting of drive->autodma.

* Add sgiioc4_speedproc() (implementation of ->speedproc method).

* Fix ->mwdma_mask (MWDMA2 mask is 0x04 not 0x02) and remove incorrect
  ->swdma_mask.  Also remove needless initialization of ->ultra_mask.

* Use ide_tune_dma() in sgiioc4_ide_dma_check(), this fixes following bugs:
  - DMA capability bit not being checked on the device
  - DMA blacklist not being checked
  - MWDMA2 mode support by device not being checked
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeremy Higdon <jeremy@sgi.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      ca1997c1
    • B
      amd74xx/via82cxxx: use ide_tune_dma() · 55f17e8d
      由 Bartlomiej Zolnierkiewicz 提交于 
      * Use ide_tune_dma() in amd74xx/via82cxxx driver, this fixes following bugs:
  - DMA capability bit not being checked on the device
  - DMA blacklist not being checked
  - DMA mode being programmed even if drive->autodma == 0
    (thus possibly destroying PIO timings)

* Bump driver version.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      55f17e8d
    • B
      ide: add ide_set{_max}_pio() (take 4) · 26bcb879
      由 Bartlomiej Zolnierkiewicz 提交于 
      * Add IDE_HFLAG_ABUSE_{PREFETCH,FAST_DEVSEL,DMA_MODES} flags
  and set them in ht6560, cmd640, cmd64x and sc1200 host drivers.

* Add set_pio_mode_abuse() for checking if host driver has a non-standard
  ->tuneproc() implementation and use it in do_special().

* Add ide_set_pio() for setting PIO mode (it uses hwif->pio_mask to find
  the maximum PIO mode supported by the host), also add ide_set_max_pio()
  wrapper for ide_set_pio() to use for auto-tuning.  Convert users of
  ->tuneproc to use ide_set{_max}_pio() where possible.  This leaves only
  do_special(), set_using_pio(), ide_hwif_restore() and ide_set_pio() as
  a direct users of ->tuneproc.

* Remove no longer needed ide_get_best_pio_mode() calls and printk-s
  reporting PIO mode selected from ->tuneproc implementations.

* Rename ->tuneproc hook to ->set_pio_mode and make 'pio' argument const.

* Remove stale comment from ide_config_drive_speed().

v2:
* Fix "ata_" prefix (Noticed by Jeff).

v3:
* Minor cleanups/fixups per Sergei's suggestions.

v4:
* Fix compile problem in drivers/ide/pci/cmd640.c
  (Noticed by Andrew Morton).

* Improve some ->set_pio_mode comments.
Reviewed-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      26bcb879
    • B
      ide: Kconfig face-lift · 842c19ad
      由 Bartlomiej Zolnierkiewicz 提交于 
      * Convert config options for PCI host drivers to select BLK_DEV_IDEPCI.

* Same for BLK_DEV_IDEDMA_PCI and PCI DMA host drivers, also make this
  config option select BLK_DEV_IDEPCI.

* Remove no longer needed help for BLK_DEV_IDEPCI and BLK_DEV_IDEDMA_PCI.

* Remove redundant IDE_CHIPSETS config option.

As a result of this patch users have now three less config options
to worry about and can just select host drivers that they need
(IDE config menu is "flatter").
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      842c19ad
    • B
      ide: move ide_rate_filter() calls to the upper layer (take 2) · f212ff28
      由 Bartlomiej Zolnierkiewicz 提交于 
      * Move ide_rate_filter() calls from host drivers to IDE core.

* Make ide_rate_filter() static.

* Make 'speed' argument of ->speedproc const.

v2:
* Fix it8213_tune_chipset() comment.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      f212ff28
    • B
      sis5513: add ->udma_filter method for chipset_family >= ATA_133 · 3160d541
      由 Bartlomiej Zolnierkiewicz 提交于 
      * Add sis5513_ata133_udma_filter() for chipset_family >= ATA_133,
  use it to filter UDMA6 mode if ATA133 bit is disabled.

* Remove no longer needed UDMA6 limiting logic from sis5513_tune_chipset().

* Bump driver version.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      3160d541
    • B
      ide: mode limiting fixes for user requested speed changes · 7670df73
      由 Bartlomiej Zolnierkiewicz 提交于 
      * Add an extra argument to ide_max_dma_mode() for passing requested transfer
  mode.  Use it as an upper limit when finding the best DMA for device/host.

* Rename ide_max_dma_mode() to ide_find_dma_mode() and at the same time add
  ide_max_dma_mode() wrapper which passes XFER_UDMA_6 as a requested mode to
  ide_find_dma_mode().  Also add inline ide_find_dma_mode() version for
  CONFIG_BLK_DEV_IDEDMA=n case.

* Pass requested transfer mode from ide_find_dma_mode() to ide_get_mode_mask()
  to avoid false warning from eighty_ninty_three().

* Use ide_find_dma_mode() to limit the user requested transfer mode in
  ide_rate_filter().  Also limit the requested mode by host max PIO mode.


Above changes make ide_rate_filter() to:

* Clip desired transfer mode down if it is invalid (values 0x0F, 0x13-0x19
  and 0x25-0x39, values > 0x46 were already clipped down, same for values
  0x25-0x39 but iff UDMA was not supported by the host).

* Clip desired transfer mode down if it is currently unsupported by IDE core
  (PIO6 and MWDMA3-4, the latter were already clipped down but iff UDMA was
  not supported by the host).

* Clip desired transfer mode down according to the host capabilities
  (UDMA modes were already clipped down but MWDMA/SWDMA/PIO weren't,
  also ->atapi_dma flag was not respected).

* Clip desired transfer mode down according to the device capabilities
  (except PIO modes for now which require mode work) - shouldn't be a
  problem since ide_set_xfer_rate() is called _after_ device has accepted
  given transfer mode.

and also result in a number of host driver specific bugfixes:

* icside
  - clip unsupported PIO5 mode down
  - fix unsupported/invalid modes being set in drive->current_speed

* ide-cris
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - clip DMA modes down for ATAPI devices
  - fix BUG() on unsupported/invalid modes

* au1xxx-ide
  - clip unsupported PIO5, SWDMA0-2 and MWDMA0-2
    (if BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA=n) modes down

* aec62xx
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - clip DMA modes down for ATAPI devices
  - fix 0x00 being programmed as PIO timing for unsupported/invalid modes
  - fix unsupported/invalid modes being set on the device

* alim15x3
  - clip DMA modes down for ATAPI devices (chipset revision == 0x20 only)
  - fix theoretical OOPS for 0x0F mode
  - fix unsupported/invalid modes being set on the device

* amd74xx
  - clip unsupported SWDMA0-2 (on COBRA_7401 revs <= 7) modes down
  - fix random PIO timings being set for unsupported/invalid modes
  - fix unsupported/invalid modes being set on the device

* atiixp
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix cached MWDMA mode being cleared for unsupported/invalid modes
  - fix PIO{0,2} timings being programmed for unsupported/invalid modes
  - fix theoretical OOPS for PIO5-6 and 0x0F modes
  - fix unsupported/invalid modes being set on the device

* cmd64x
  - clip unsupported SWDMA0-2 modes down

* cs5530
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix unsupported/invalid modes being set on the device
  - fix BUG() on unsupported/invalid modes
    (which happened if the device accepted the setting)

* cs5535
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix unsupported/invalid modes being set on the device
  - fix theoretical OOPS for PIO5-6 and 0x0F modes

* hpt34x
  - clip DMA modes down for ATAPI devices
  - fix invalid timings being programmed for unsupported/invalid modes
  - fix unsupported/invalid modes being set on the device

* hpt366
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix PIO0 timings being programmed for unsupported/invalid modes
  - fix DMA timings being cleared for MWDMA3-4 and 0x25-0x39 modes
  - fix unsupported/invalid modes being set on the device

* it8213
  - clip unsupported PIO5, SWDMA0-1 and MWDMA0 modes down

* it821x
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - clip DMA modes down for ATAPI devices
    (chipset in smart mode and revision 0x10 in pass-through mode)

* jmicron
  - clip unsupported SWDMA0-2 modes down
  - fix unsupported/invalid modes being set on the device

* pdc202xx_new
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix unsupported/invalid modes being set on the device

* pdc202xx_old
  - clip unsupported PIO5 mode down
  - fix incorrect timings being set for unsupported/invalid modes
  - fix unsupported/invalid modes being set on the device

* piix
  - clip unsupported PIO5, SWDMA0-1 and MWDMA0 modes down

* sc1200
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix unsupported/invalid modes being set on the device
  - fix BUG() on unsupported/invalid modes
    (which happened if the device accepted the setting)

* scc_pata
  - clip unsupported PIO5, SWDMA0-2 and MWDMA0-2 modes down

* serverworks
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix DMA/UDMA timings/settings being cleared for unsupported/invalid modes
  - fix unsupported/invalid modes being set on the device

* siimage
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - clip DMA modes down for ATAPI devices (SATA chipsets)

* sis5513
  - clip unsupported PIO5 mode down
  - fix BUG() on unsupported/invalid modes

* sl82c105
  - clip unsupported SWDMA0-2 modes down

* slc90e66
  - clip unsupported PIO5, SWDMA0-1 and MWDMA0 modes down

* tc86c001
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix PIO0 timings being programmed for PIO5/0x0F/SWDMA0-2/0x13-0x19 modes
  - fix invalid 0x00 DMA timing being programmed for MWDMA3-4/0x25-0x39 modes
  - fix unsupported/invalid modes being set on the device

* triflex
  - clip unsupported PIO5 mode down

* via82cxxx
  - fix random PIO timings being set for unsupported/invalid modes
  - fix unsupported/invalid modes being set on the device

* pmac
  - clip unsupported PIO5 and SWDMA0-2 modes down

* cmd640/ht6560b
  - clip DMA modes down (if CONFIG_BLK_DEV_IDEDMA=y)
  - fix PIO5 being clipped to PIO4 (if CONFIG_BLK_DEV_IDEDMA=n)

* opti621
  - clip DMA modes down (if CONFIG_BLK_DEV_IDEDMA=y)
  - clip unsupported PIO4 to PIO3 (if CONFIG_BLK_DEV_IDEDMA=n)


While at it:

* Use ide_rate_filter() in cs5520.c::cs5520_tune_chipset().

* Remove no longer needed checks from hpt366.c::hpt3{6,7}x_tune_chipset().
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      7670df73
    • B
      ide: add missing ide_rate_filter() calls to ->speedproc()-s · a8028fcb
      由 Bartlomiej Zolnierkiewicz 提交于 
      * Fix icside, cris-ide, au1xxx-ide, amd74xx, via82cxxx and pmac host drivers
  to use ide_rate_filter().

  This results in the following modes (from user requests) being clipped down:
  - invalid modes (values 0x46-0xFF)  [ for all hosts ]
  - unsupported by a host UDMA modes  [ for hosts which support UDMA]
  - all UDMA modes and MWDMA3-4 modes [ for hosts which don't support UDMA ]
  - invalid modes (values 0x25-0x39)  [ for hosts which don't support UDMA ]

* Host driver specific changes in behavior:

  icside:
    - no change

  cris-ide
    - clip unsupported UDMA3-6 modes down
    - fix BUG() on trying to set unsupported UDMA3-6 modes

  au1xxx-ide/pmac
    - clip unsupported UDMA modes down

  amd74xx/via82cxxx
    - clip unsupported UDMA modes down
    - fix random PIO timings being set for unsupported/invalid modes
    - fix unsupported/invalid modes being set on the device

* While at it remove no longer needed checks from pmac.c driver.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      a8028fcb
    • S
      ide: call udma_filter() before resorting to the UltraDMA mask · 851dd33b
      由 Sergei Shtylyov 提交于 
      Give the udma_filter() method call precedence over using the mode masks.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      851dd33b
    • T
      ide: make jmicron match vendor and device class · bda7970c
      由 Tejun Heo 提交于 
      PATA part of all current JMB controllers behave the same way and
JMicron confirms that all future ones will stay compatible.  Matching
vendor and device class is enough.

For backward compatibility, jmicron still needs to match 361,3,5,6,8
DIDs regardless of device class if libata is not configured but won't
need further DID update from this point.

Bart: cosmetic fixes to jmicron_chipset
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Ethan Hsiao <ethanhsiao@jmicron.com>
Cc: Justin Tsai <justin@jmicron.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      bda7970c
    • S
      pdc202xx_new: switch to using pci_get_slot() (take 2) · 07047935
      由 Sergei Shtylyov 提交于 
      Switch to using pci_get_slot() in init_setup_pdc20270() to get to the mate chip
behind DC21150 bridge as there's no need for the driver itself to walk the list
of the PCI devices (and the driver didn't check the bus # of the found device).
While at it, make it emit warning about IRQ # being fixed up (just like hpt366.c
does) and "beautify" this whole function as well as init_setup_pdc20276()...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      07047935
    • S
      ide: hook ACPI _PSx method to IDE power on/off · 5e32132b
      由 Shaohua Li 提交于 
      ACPI spec defines the sequence of IDE power on/off:
Powering down:
	Call _GTM.
	Power down drive (calls _PS3 method and turns off power planes).
Powering up:
	Power up drive (calls _PS0 method if present and turns on power planes).
	Call _STM passing info from _GTM (possibly modified), with ID data from
	each drive.
	Initialize the channel.
	May modify the results of _GTF.
	For each drive:
		Call _GTF.
		Execute task file (possibly modified).
This patch adds the missed _PS0/_PS3 methods call.
Signed-off-by: NShaohua Li <shaohua.li@intel.com>
Acked-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      5e32132b
    • A
      ide: Platform IDE driver · 8cb1f567
      由 Anton Vorontsov 提交于 
      This is now very similar to pata_platform.c, they both use
same platform data structure and same resources.

To achieve that, byte_lanes_swapping platform data variable
and platform specified iops removed from that driver. It's fine,
since those were never used anyway.

pata_platform and ide_platform are carrying same driver names,
to easily switch between these drivers, without need to touch
platform code.

Bart:
- build fix from Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NVitaly Bordug <vitb@kernel.crashing.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      8cb1f567
    • S
      hpt366: MWDMA filter for SATA cards (take 2) · b4e44369
      由 Sergei Shtylyov 提交于 
      The Marvell bridge chips used on HighPoint SATA cards do not seem to support
the MWDMA modes (at least that could be seen in their so-called drivers :-),
so the driver needs to account for this -- to achieve this:

- add mdma_filter() method from the original patch by Bartlomiej Zolnierkiewicz
  with his consent;

- install the method for all chips to only return empty mask if a SATA drive
  is detected on HPT372{AN]/374 chips...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      b4e44369
    • S
      atiixp: SB700 contains more than one IDE channel · 7cfa7168
      由 Shane Huang 提交于 
      SB700 supports one physical IDE channel, but SB700 SATA controller
supports combined mode.  When the SATA combined mode is enabled,
two SATA ports (port4 and port5) share one IDE channel from IDE
controller, and PATA will share the other IDE channel.

Our previous patch adding SB700 IDE device ID only supports one
IDE channel, which contains bug.  The attached patch fixes the bug.
Signed-off-by: N"Shane Huang" <Shane.Huang@amd.com>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      7cfa7168
  3. 10 10月, 2007 4 次提交
  5. 09 10月, 2007 10 次提交
  7. 08 10月, 2007 10 次提交