Rather than have build_mlx_header() return a negative value on failure
and the length of the segments it builds on success, add a pointer
parameter to return the length and return 0 on success.  This matches
the calling convention used for build_lso_seg() and generates slightly
smaller code -- eg, on 64-bit x86:

add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-22 (-22)
function                                     old     new   delta
mlx4_ib_post_send                           2023    2001     -22
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add TSO support to the mlx4_ib driver.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

For HCAs that support TCP segmentation offload (IB_DEVICE_UD_TSO), set
NETIF_F_TSO and use HW LSO to offload TCP segmentation.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

LSO (large send offload) allows the networking stack to pass SKBs with
data size larger than the MTU to the IPoIB driver and have the HCA HW
fragment the data to multiple MSS-sized packets.  Add a device
capability flag IB_DEVICE_UD_TSO for devices that can perform TCP
segmentation offload, a new send work request opcode IB_WR_LSO,
header, hlen and mss fields for the work request structure, and a new
IB_WC_LSO completion type.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add a create_flags member to struct ib_qp_init_attr that will allow a
kernel verbs consumer to create a pass special flags when creating a QP.
Add a flag value for telling low-level drivers that a QP will be used
for IPoIB UD LSO.  The create_flags member will also be useful for XRC
and ehca low-latency QP support.

Since no create_flags handling is implemented yet, add code to all
low-level drivers to return -EINVAL if create_flags is non-zero.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add support for reading newer card's EEPROMs while continuing to support
older EEPROMs.

Also, add support for the temperature sensor if present.
Signed-off-by: NMichael Albaugh <Michael.Albaugh@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This reduces the latency for RC ACKs when a PIO buffer is available.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

A fixed partitioning of send buffers is determined at driver load time
for user processes and kernel use.  Since send buffers are a scarce
resource, it makes sense to allow the kernel to use the buffers if they
are not in use by a user process.

Also, eliminate code duplication for ipath_force_pio_avail_update().
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The link can be put in LINKDOWN_DISABLE state either locally or via a
MAD.  However, the link-recovery code will take it out of that state as
a side-effect of attempts to clear SerDes/XGXS issues.

We add a flag to indicate "link is down on purpose, leave it alone."
Signed-off-by: NMichael Albaugh <michael.albaugh@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Update the module author to the current email address.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

In list iteration code, you normally wouldn't be calling
"container_of()" directly anyway, you'd be invoking "list_entry()".
But you don't even need that here, "list_for_each_entry()" is fine.
Signed-off-by: NRobert P. J. Day <rpjday@crashcourse.ca>
Acked-by: NGlenn Streiff <gstreiff@neteffect.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Convert list_splice() + INIT_LIST_HEAD() to the equivalent list_splice_init()
Signed-off-by: NRobert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The function rdma_create_id() always returns either a valid pointer or
a value made with ERR_PTR, so its result should be tested with IS_ERR,
not with a test for 0.

The problem was found using the following semantic match.
(http://www.emn.fr/x-info/coccinelle/)

//<smpl>
@a@
expression E, E1;
statement S,S1;
position p;
@@

E = rdma_create_id(...)
... when != E = E1
if@p (E) S else S1

@n@
position a.p;
expression E,E1;
statement S,S1;
@@

E = NULL
... when != E = E1
if@p (E) S else S1

@depends on !n@
expression E;
statement S,S1;
position a.p;
@@

* if@p (E)
  S else S1
//</smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The session_id members of struct nes_cm_listener and struct
nes_cm_node are write-only, so remove them.  This allows the
session_id member of struct nes_cm_core to be removed as well, since
it is only used to write those other session_id values.

This removes the use of current->tgid (which will be deprecated)
pointed out by Pavel Emelyanov <xemul@openvz.org>.
Acked-by: NGlenn Streiff <gstreiff@neteffect.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

In slave_or_pri_blk(), pci_write_config_byte() is used to write a
16-bit quantity to clear linkctrl CRC error bits.  This is clearly a
bug and also causes the warning

    drivers/infiniband/hw/ipath/ipath_iba6110.c: In function 'slave_or_pri_blk':
    drivers/infiniband/hw/ipath/ipath_iba6110.c:849: warning: overflow in implicit constant conversion

Fix this by using pci_write_config_word() instead.
Acked-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The receive queue number of WRs and SGEs shouldn't be checked if a
SRQ is specified.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Remove useless comment about list removal since locks are held and
the code checks that the QP is on the list before removing it.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Workaround a QLE7140 problem that in rare cases causes flow control
problems after link recovery by forcing a link retrain after recovery.
A module parameter is provided to control the behavior in case it causes
problems.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch adds code to get/set portinfo to support multiple link speeds
and widths.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

There's a conflict between our need to quiesce PSM-based applications
to avoid HoL blocking when the IB link goes down and the apps' desire
to remain running so that their quiescence timout mechanism can keep
running.

The compromise is to STOP the processes for a fixed period of time and
then alternate between CONT and STOP until the link is again active.

If there are poor interactions with subnet manager configuration at a
given site, the interval can be adjusted via a module paramter.
Signed-off-by: NJohn Gregor <john.gregor@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Don't try to handle freeze mode HW errors if the driver is in diagnostic
mode since some tests can cause errors that shouldn't be processed.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The check for link up was incorrect, thus setting the LED display
inconsistently with the link state.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The error recovery code for updating the driver's cached status information
for which send buffers are busy or free wasn't updated for IBA7220.
It should be similar to the initialization code in enable_chip().
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Fix byte order of value assigned to pioavailshadow.  This bug was
detected by sparse endianness warnings.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

In mthca_alloc_icm_table(), the number of entries to allocate for the
table->icm array is computed by calculating obj_size * nobj and then
dividing by MTHCA_TABLE_CHUNK_SIZE.  If nobj is really large, then
obj_size * nobj may overflow and the division may get the wrong value
(even a negative value).  Fix this by calculating the number of
objects per chunk and then dividing nobj by this value instead.

This patch allows crazy configurations such as loading ib_mthca with
the module parameter num_mtt=33554432 to work properly.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

mthca_make_profile() returns the size in bytes of the HCA context
layout it creates, or a negative value if an error occurs.  However,
the return value is declared as u64 and the memfree initialization
path casts this value to int to test if it is negative.  This makes it
think incorrectly than an error has occurred if the context size
happens to be bigger than 2GB, since this turns into a negative int.

Fix this by having mthca_make_profile() return an s64 and testing
for an error by checking whether this 64-bit value itself is negative.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Pavel Emelyanov <xemul@openvz.org> mentioned in <http://lkml.org/lkml/2008/3/17/131>
that the task_struct->tgid field is about to become deprecated, so the
uses in the ehca driver need to be fixed up.

However, all the uses in ehca are for some object ownership checking
that is not really needed, and anyway is implementing a policy that
should be in common code rather than a low-level driver.  So just
remove all the checks.
Signed-off-by: NHoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The current SRP initiator will allow unlimited s/g entries in the
indirect descriptors lists, but the entry count field in the SRP_CMD
request is 8 bits, so setting srp_sg_tablesize too large will open the
possibility of wrapping the count and generating invalid requests.

Clamp srp_sg_tablesize to the protocol limits to prevent surprises.

Reported by Martin W. Schlining III <mschlining@datadirectnet.com>.
Signed-off-by: NDavid Dillow <dillowda@ornl.gov>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Enable use of 4KB MTU.  Since the driver uses more pinned memory for
receive buffers when the 4KB MTU is enabled, whether or not the fabric
supports that MTU, add a "mtu4096" module parameter that can be used to
limit the MTU to 2KB when it is known that 4KB MTUs can't be used
anyway.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The code was checking if units are present, but not that present units
were usable (link up, etc.)
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Modern I/O buses like PCIe and HT can be configured for multiple speeds
and widths.  When an ipath HCA seems to have lower than expected
performance, it is very useful to be able to display what the driver
thinks the bus speed is.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch makes some constants chip-specific, and makes some related
changes to prepare for supporting another HCA.

Signed-off-by: Dave Olson <dave.olson@qlogic.com
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Recent sparse versions and kernel cleanups knock down the false positive
rate of the ipath driver code to a point where having it be sparse clean
is worthwhile. Here we fixup the sparse warnings.  Some of these warnings
(and the impetus to run sparse again) are due to work by Roland Dreier.
Signed-off-by: NArthur Jones <arthur.jones@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Arbel and Sinai devices support checksum generation and verification
of TCP and UDP packets for UD IPoIB messages.  This patch checks if
the HCA supports this and sets the IB_DEVICE_UD_IP_CSUM capability
flag if it does.  It implements support for handling the IB_SEND_IP_CSUM
send flag and setting the csum_ok field in receive work completions.
Signed-off-by: NEli Cohen <eli@mellnaox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

ConnectX devices support checksum generation and verification of TCP
and UDP packets for UD IPoIB messages.  This patch checks if the HCA
supports this and sets the IB_DEVICE_UD_IP_CSUM capability flag if it
does.  It implements support for handling the IB_SEND_IP_CSUM send
flag and setting the csum_ok field in receive work completions.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NAli Ayub <ali@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

For HCAs that support checksum offload (ie that set IB_DEVICE_UD_IP_CSUM
in the device capabilities flags), have IPoIB set NETIF_F_IP_CSUM and
use the HCA to generate and verify IP checksums.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

__FUNCTION__ is gcc-specific, use __func__ instead.
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Allow the compiler to optimize better and generate smaller code:

add/remove: 0/6 grow/shrink: 2/0 up/down: 1528/-1864 (-336)
function                                     old     new   delta
.ehca_set_pagebuf                           1344    2172    +828
.ehca_probe                                 2312    3012    +700
ehca_set_pagebuf_phys                         24       -     -24
ehca_set_pagebuf_fmr                          24       -     -24
ehca_init_device                              24       -     -24
.ehca_set_pagebuf_fmr                        480       -    -480
.ehca_set_pagebuf_phys                       512       -    -512
.ehca_init_device                            800       -    -800

Also this fixes warnings like:

    drivers/infiniband/hw/ehca/ehca_mrmw.c:2015:5: warning: symbol 'ehca_set_pagebuf_fmr' was not declared. Should it be static?
Signed-off-by: NRoland Dreier <rolandd@cisco.com>