Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 03 8月, 2017 7 次提交
  3. 02 8月, 2017 5 次提交
  5. 01 8月, 2017 3 次提交
    • V
      powerpc/kernel: Avoid preemption check in iommu_range_alloc() · 75f327c6
      由 Victor Aoqui 提交于 
      Replace the __this_cpu_read() with raw_cpu_read() in
iommu_range_alloc(). Otherwise we get a warning about using
__this_cpu_read() in preemptible code:

  BUG: using __this_cpu_read() in preemptible
  caller is iommu_range_alloc+0xa8/0x3d0

Preemption doesn't need to be disabled since according to the comment
any CPU can safely use any IOMMU pool.
Signed-off-by: NVictor Aoqui <victora@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
      75f327c6
    • G
      powerpc/powernv: Clear PECE1 in LPCR via stop-api only on Hotplug · 24be85a2
      由 Gautham R. Shenoy 提交于 
      Currently we use the stop-api provided by the firmware to program the
SLW engine to restore the values of hypervisor resources that get lost
on deeper idle states (such as winkle). Since the deep states were
only used for CPU-Hotplug on POWER8 systems, we would program the LPCR
to have the PECE1 bit since Hotplugged CPUs shouldn't be spuriously
woken up by decrementer.

On POWER9, some of the deep platform idle states such as stop4 can be
used in cpuidle as well. In this case, we want the CPU in stop4 to be
woken up by the decrementer when some timer on the CPU expires.

In this patch, we program the stop-api for LPCR with PECE1
bit cleared only when we are offlining the CPU and set it
back once the CPU is online.
Signed-off-by: NGautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
      24be85a2
    • G
      powerpc/powernv: Save/Restore additional SPRs for stop4 cpuidle · e1c1cfed
      由 Gautham R. Shenoy 提交于 
      The stop4 idle state on POWER9 is a deep idle state which loses
hypervisor resources, but whose latency is low enough that it can be
exposed via cpuidle.

Until now, the deep idle states which lose hypervisor resources (eg:
winkle) were only exposed via CPU-Hotplug.  Hence currently on wakeup
from such states, barring a few SPRs which need to be restored to
their older value, rest of the SPRS are reinitialized to their values
corresponding to that at boot time.

When stop4 is used in the context of cpuidle, we want these additional
SPRs to be restored to their older value, to ensure that the context
on the CPU coming back from idle is same as it was before going idle.

In this patch, we define a SPR save area in PACA (since we have used
up the volatile register space in the stack) and on POWER9, we restore
SPRN_PID, SPRN_LDBAR, SPRN_FSCR, SPRN_HFSCR, SPRN_MMCRA, SPRN_MMCR1,
SPRN_MMCR2 to the values they had before entering stop.
Signed-off-by: NGautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
      e1c1cfed
  7. 31 7月, 2017 3 次提交
    • R
      powerpc/mm: Fix check of multiple 16G pages from device tree · 23493c12
      由 Rui Teng 提交于 
      The offset of hugepage block will not be 16G, if the expected
page is more than one. Calculate the totol size instead of the
hardcode value.

Fixes: 4792adba ("powerpc: Don't use a 16G page if beyond mem= limits")
Signed-off-by: NRui Teng <rui.teng@linux.vnet.ibm.com>
Tested-by: NAnshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
      23493c12
    • M
      powerpc/udbg: Reduce the footgun potential of EARLY_DEBUG_LPAR(_HVSI) · 9227f043
      由 Michael Ellerman 提交于 
      For debugging very early boot problems we have CONFIG_PPC_EARLY_DEBUG,
which allows configuring the kernel such that it unconditionally writes
to a particular type of console, regardless of whether that console
exists or not. This is useful sometimes when the kernel crashes before
it can even determine what platform it's on, and therefore what consoles
exist.

However if you boot a kernel built this way on a different platform, it
will generally crash because it writes to a console that doesn't exist.

A particularly nasty instance of this is if you enable the hypervisor
console early debug, and then boot that kernel on bare metal. The result
is that the kernel calls "the hypervisor" very early in boot, but the
kernel *is* the hypervisor, so we jump to the system call handler and
start executing all sorts of code that isn't ready to be run. This may
lead to a machine check or check stop depending on how lucky you are.

Luckily there is an easy way to avoid this particular case. We simply
read the MSR before installing the hooks, and if we see MSR_HV is set
then we are the hypervisor and we definitely should not use the
hypervisor console.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
      9227f043
    • M
      powerpc/configs: Add a powernv_be_defconfig · 3603c52f
      由 Michael Ellerman 提交于 
      Although pretty much everyone using powernv is running little endian,
we should still test we can build for big endian. So add a
powernv_be_defconfig, which is autogenerated by flipping the endian
symbol in powernv_defconfig.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Reviewed-by: NCyril Bur <cyrilbur@gmail.com>
      3603c52f
  9. 25 7月, 2017 4 次提交
  11. 24 7月, 2017 12 次提交
  13. 23 7月, 2017 6 次提交