patch_via.c has redundant codes for parsing the input-pins.  Although
they are pretty similar, but all implemented in different functions
just because of hard-coded ids and slight incompatibilities.
This patch refactors the codes to use the common helper function,
resulting in the reduction of many lines.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Instead of defining each content as a separate struct, put all into the
definition of struct alc_fixup arrays so that reader doesn't go back to
see the definition again.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The attached patch enables playback on a Sony VAIO machine.

BugLink: http://launchpad.net/bugs/618271Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Cc: <stable@kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch adds quirk for the Lenovo S10-3t so the headphone &
microphone jacks will now work.
Signed-off-by: NJerone Young <jerone.young@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The new sticky PCM parameter introduced the delayed clean-ups of
stream- and channel-id tags.  In the current implementation, this check
(adding dirty flag) and actual clean-ups are done only for the codec
chip.  However, with HD-audio architecture, multiple codecs can be
on a single bus, and the controller assign stream- and channel-ids in
the bus-wide.

In this patch, the stream-id and channel-id are checked over all codecs
connected to the corresponding bus.  Together with it, the mutex is
moved to struct hda_bus, as this becomes also bus-wide.
Reported-and-tested-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Intel and Nvidia HDMI codec drivers have own implementations of
sticky PCM parameters.  Now HD-audio core part already has it,
thus both setups conflict.  The fix is simply remove the part in
patch_intelhdmi.c and patch_nvhdmi.c and simply call
snd_hda_codec_setup_stream() as usual.
Reported-and-tested-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

hdmi_eld_update_pcm_info() must be always compiled in.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Just added new codec ids.  These are almost compatible with existing ones.
Signed-off-by: NCharles Chin <Charles.Chin@idt.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

 - Fix capture mixer elements for ALC680 base model
 - Support auto change ADC for recording from MIC
 - Cancel capture source assigned in auto mode.
Signed-off-by: NKailang Yang <kailang@realtek.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

model=dell-vostro is needed for Dell Vostro 1220 with Coexnat 5067.

Reference: Novell bnc#631066
	https://bugzilla.novell.com/show_bug.cgi?id=631066

Cc: <stable@kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The commit eb541337
    ALSA: hda - Make converter setups sticky
changes the semantics of snd_hda_codec_cleanup_stream() not to clean up
the stream at that moment but delay the action.  This broke the codes
expecting that the clean-up is done immediately, such as dynamic ADC
changes in some codec drivers.

This patch fixes the issue by introducing a lower helper,
__snd_hda_codec_cleanup_stream(), to allow the immediate clean up.
The original snd_hda_codec_cleanup_stream() is kept as is now.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When a device is plugged over HDMI, it passes some information in ELD
including the supported PCM parameters like formats, rates, channels.
This patch adds the check to PCM open callback of HDMI streams so that
only valid parameters the device supports are used.

When no device is plugged, the parameters the codec supports are used;
it's mostly all parameters the hardware can work.  This is for apps
that are started before device plugging and do probing (e.g. a sound
daemon), so that at least, probing would work even before the device
plugging.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Added the entries for 92HD87B1/3 and 92HD87B2/4 codecs.
These are compatible with existing 83xxx codecs.
Signed-off-by: NCharles Chin <Charles.Chin@idt.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Two users report model=auto is needed to make the internal mic work properly.
BugLink: https://bugs.launchpad.net/bugs/495134Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

* Add missing codec IDs.
* Modify some existing codec names for discrete GPUs to match newly
  added IDs. Note: existing names were a mixture of marketing and
  engineering GPU names. Equally, there's no reason that codec IDs
  have to be specific to a particular GPU or board, so identify
  codecs in a less marketing-oriented fashion.
* Reformat codec ID table so it's easier to read, for me at least.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The Conexant CX20584 with 141f:5068 seems compatible with other
cxt5066 code.  Just add the missing id.
Tested-by: NCristopher Camacho Leandro <ccamacho@linuxmail.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

  This provides a new model and pin config for the snd-hda-intel
92HD83XXX codec for hp laptop model dv7-4000, enabling the subwoofer.

Signed-off-by: Steven Eastland <seastland at gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

I discovered tonight that ALSA no longer sets up a stream for the second ADC
provided by the Realtek ALC260 HDA codec.  At some point alc_build_pcms()
started using stream_analog_alt_capture when constructing the second ADC
stream, but patch_alc260() was never updated accordingly.  I have no idea
when this regression occurred.  The trivial patch to patch_alc260() given
below fixes the problem as far as I can tell.  The patch is against 2.6.35.
Signed-off-by: NJonathan Woithe <jwoithe@physics.adelaide.edu.au>
Cc: <stable@kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

So far, we reset the converter setups like the stream-tag, the
channel-id and format-id in prepare callbacks, and clear them in
cleanup callbacks.  This often causes a silence of the digital
receiver for a couple of seconds.

This patch tries to delay the converter setup changes as much as
possible.  The converter setups are cached and aren't reset as long
as the same values are used.  At suspend/resume, they are cleared
to be recovered properly, too.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NKailang Yang <kailang@realtek.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The NID 0x11 on HP dc5750 with ALC260 should be a speaker although BIOS
gives it as a line-out.  This patch adds a quirk to fix the pin config
so that the real line-out is used properly.

Reference: bnc#624118
	https://bugzilla.novell.com/show_bug.cgi?id=624118Signed-off-by: NTakashi Iwai <tiwai@suse.de>

In patch_alc269(), we initialize the primary capsrc so that the device
works from the beginning.  It issues CONNECT_SEL verb no matter which
widget is although some widget (e.g. 0x23) has no connection selection
but a mixer, which requires unmuting instead.

This patch fixes the initialization of capsrc by re-using the code as
a helper function.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

An Intel board needs a white-list entry to enable PC-beep.
Otherwise the driver misdetects (due to bogus BIOS info) and ignores
the PC-beep on 2.6.35.
Reported-and-tested-by: NLeandro Lucarella <luca@llucax.com.ar>
Cc: <stable@kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Since the pending periods are often bogus and take long time until
actually processed, it often results in a high CPU usage of the hd-audio
workq.  Overall it's better to have low CPU consumption by avoiding a
too tight loop rather than the wake-up timing accuracy.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Define constants for the HD-audio stream format bits, and replace the
magic numbers in codes.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Fix HDA beep frequency on IDT 92HD73xx and 92HD71Bxx codecs.
These codecs use the standard beep frequency calculation although the
datasheet says it's linear frequency.

Other IDT/STAC codecs might have the same problem.  They should be
fixed individually later.
Signed-off-by: NDaniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Passing IEC 61937 encapsulated compressed audio at bitrates over 6.144
Mbps (i.e. more than a single 2-channel 16-bit 192kHz IEC 60958 link)
over HDMI requires the use of HBR Audio Stream Packets instead of Audio
Sample Packets.

Enable HBR mode when the stream has 8 channels and the Non-PCM bit is
set.

If the audio converter is not connected to any HBR-capable pins, return
-EINVAL in prepare().
Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Set bit 15 (Stream Type) of HDA Stream Format to 1 (Non-PCM) when IEC958
channel status bit 1 (AES0 & 0x02) is set to 1 (non-audio).

This is a prequisite for HDMI HBR passthrough.
Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Just as with the X301. The X300 does not have a way to do SPDIF either.
It does not have a dock connector, nor does it have the SPDIF through
the headphone jack.

This patch fixes it so X300 does not show SPDIF, since it cannot do it.

To add all Lenovo Thinkpads had different codec subsytem IDs:

X300:
http://launchpadlibrarian.net/34862838/Card0.Codecs.codec.0.txtSigned-off-by: NJerone Young <jerone.young@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

ALSA: hda - FIX to not expose SPDIF on Thinkpad X301, since it does not have the ability to use SPDIF

The Lenovo X301 does not have the ability to connect to a docking
station to use the SPDIF port. It also does not have the ability to do
SPDIF though the headphone jack or Display Port jacks.

This patch fixes it so this is not exposed for the X301 and users do
think it has the ability to do SPDIF.

I tested both headphone & display port jacks and it is not there. I have
tested this patch and it works great.

Also to add the other Thinkpads have different subsystem codec IDs.
Here are examples:

X301:
http://launchpadlibrarian.net/31561902/Card0.Codecs.codec.0.txt

X200:
http://launchpadlibrarian.net/49055036/Card0.Codecs.codec.0.txt

W500:
http://launchpadlibrarian.net/36276057/Card0.Codecs.codec.0.txtSigned-off-by: NJerone Young <jerone.young@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The current ALC259/268/269 parser ignores some pins as unhandled,
but user won't notice what goes wrong.  So, added a warning message
for the ignored pins as a hint.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The pin NID 0x1a should be handled as well as NID 0x1b.
Also added comments.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Call snd_hda_shutup_pins() for power-saving and reboot-notifier in
patch_conexant.c as well as other codecs.  This will reduce the pop
noise in power-save mode.

Reference: bnc#624896
	https://bugzilla.novell.com/show_bug.cgi?id=624896Signed-off-by: NTakashi Iwai <tiwai@suse.de>

If BIOS sets up the input pin as VREF 50, use the value as is instead of
overriding forcibly to VREF 80.  This fixes the quality of inputs on
some devices like Packard-Bell M5210.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Since ALC259/269 use the same parser of ALC268, the pin 0x1b was ignored
as an invalid widget.  Just add this NID to handle properly.
This will add the missing mixer controls for some devices.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Make a helper function to parse the digital I/Os of all Realtek codecs
to simplify the code and to ensure the setups.
Also, initialize digital I/O pins properly in init callbacks.  Some BIOS
seem to leave pins uninitialized.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Some ALC662-compatible codecs like ALC892 may have more than 4
connections for the input source.  Use HDA_MAX_CONNECTIONS instead of
the fixed magic number 4.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add a prefix and more information for error messages regarding the
connection-list in hda_codec.c.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The non-standard name "iMic" makes PulseAudio ignore the microphone.
BugLink: https://launchpad.net/bugs/605101Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>