Reorganize ata_host_alloc() and its subroutines into the following
three functions.

* ata_host_alloc() : allocates host and its ports.  shost is not
  registered automatically.

* ata_scsi_add_hosts() : allocates and adds shosts associated with an
  ATA host.  Used by ata_host_register().

* ata_host_register() : takes a fully initialized ata_host structure
  and registers it to libata layer and probes it.

Only ata_host_alloc() and ata_host_register() are exported.
ata_device_add() is rewritten using the above functions.  This patch
does not introduce any observable behavior change.  Things worth
mentioning.

* print_id is assigned at registration time and LLDs are allowed to
  overallocate ports and reduce host->n_ports during initialization.
  ata_host_register() will throw away unused ports automatically.

* All SCSI host initialization stuff now resides in
  ata_scsi_add_hosts() in libata-scsi.c, where it should be.

* ipr is now the only user of ata_host_init().  Either kill it by
  converting ipr to use ata_host_alloc() and friends or rename and
  move it to libata-scsi.c
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Separate out ata_host_start() from ata_device_add().  ata_host_start()
calls ->port_start on each port if available and freezes the port.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Don't embed ap inside shost.  Allocate it separately and point it back
from shosts's hostdata.  This makes port allocation more flexible and
allows regular ATA and SAS share host alloc/init paths.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add PCI ID for new VIA chip.  Original patch is from Maarten Vanraes.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Maarten Vanraes <maarten.vanraes@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

kill the following compile warning.

drivers/ata/libata-core.c:1786: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

    SB600 RAID and SB600 SATA is the same controller and share the
same PCI ID 0x4380. There is no such PCI ID 0x4381.
Signed-off-by: NConke Hu <conke.hu@gmail.com>
 ---------
Signed-off-by: NJeff Garzik <jeff@garzik.org>

->post_internal_cmd is simplified EH for internal commands.  Its
primary mission is to stop the controller such that no rogue memory
access or other activities occur after the internal command is
released.  It may provide error diagnostics by setting qc->err_mask
but this hasn't been a requirement.

To ignore SETXFER failure for CFA devices, libata needs to know
whether a command was failed by the device or for any other reason.
ie. internal command needs to get AC_ERR_DEV right.

This patch makes the following changes to AC_ERR_DEV handling and
->post_internal_cmd semantics to accomodate this need and simplify
callback implementation.

1. As long as the correct bits in the result TF registers are set,
   there is no need to set AC_ERR_DEV explicitly.  libata EH core
   takes care of that for both normal and internal commands.

2. The only requirement for ->post_internal_cmd() is to put the
   controller into quiescent state.  It needs not to set any err_mask.

3. ata_exec_internal_sg() performs minimal error analysis such that
   AC_ERR_DEV is automatically set as long as result_tf is filled
   correctly.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Disabled port handling in ata_pci_init_native_mode() is slightly
broken in that it may end up using the wrong port_info.  This patch
updates it such that disables ports are made dummy as done in the
legacy and other cases.

While at it, fix indentation in ata_resources_present().
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Move cross checking between port_map and cap.n_ports into
ahci_save_initial_config().  After save_initial_config is done,
hpriv->port_map is always setup properly.

Tested on JMB363, ICH7 and ICH8 (with dummy ports).
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

There are several registers which describe how the controller is
configured.  These registers are sometimes implemented as r/w
registers which are configured by firmware and get cleared on
controller reset or after suspend/resume cycle.  ahci saved and
restored those values inside ahci_reset_controller() which is a bit
messy and doesn't work over suspend/resume cycle.

This patch implements ahci_save/restore_initial_config().  The save
function is called during driver initialization and saves cap and
port_map to hpriv.  The restore function is called after the
controller is reset to restore the initial values.

Sometimes the initial firmware values are inconsistent and need to be
fixed up.  This is handled by ahci_save_initial_config().  For this,
there are two versions of saved registers.  One to write back to the
hardware register, the other to use during driver operation.  This is
necessary to keep ahci's behavior unchanged (write back fixed up
port_map while keeping cap as-is).

This patch makes ahci save the register values once before the first
controller reset, not after it's been reset.  Also, the same stored
values are used written back after each reset, so the register values
are properly recovered after suspend/resume cycle.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Promise ATA ports should always be reset by pdc_reset_port()
when errors are detected, but the recent error reason decoding
update to sata_promise replaced that reset with a freeze.

This patch changes the error detection to do a reset again.
This makes the error decoding update safer, as it now only
adds error decoding without changing any other behaviour.
Signed-off-by: NMikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAlan Cox <alan@redhat.com>

Correct missing modefilter (crash if BAR4 unassigned)
Use Cable Detect method
Wrap ->set_mode instead ready for ->post_set_mode removal
Maxtor errata as per Jeff Garzik report
Remove duplicated private udma_mask hacking
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Not a PCI device so doesn't need PCI includes
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Versus upstream as requested

Last of the trivial switches to cable_detect methods.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The READ/WRITE LONG commands are theoretically obsolete,
but the majority of drives in existance still implement them.

The WRITE_LONG and WRITE_LONG_ONCE commands are of particular
interest for fault injection testing -- eg. creating "media errors"
at specific locations on a disk.

The fussy bit is that these commands require a non-standard
sector size, usually 520 bytes instead of 512.

This patch adds support to libata for READ/WRITE LONG commands
issued via SG_IO/ATA_16.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The Asus W5F laptop uses a short cable instead of the 80-wire style, and thus
needs to be in the ich_laptop special cases for correct detection and support
of UDMA/100 for the hard drive. I noticed this because I have the W5F laptop,
and was tracing apparent slowness.
Signed-off-by: NRobin H. Johnson <robbat2@gentoo.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

A lot of noise because I had to rename the optidma_set_mode() method to
avoid confusion with the new ->set_mode() method that was added. Cable
detect side is pretty trivial.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAlan Cox <number6@the-village.bc.nu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Reading from the ATA shadow registers while we are in ADMA mode may cause
undefined behavior.  Don't read the ATA status register when completing
commands for this reason, it shouldn't be needed as the controller will
notify us if the command failed.  Also, don't allow commands with result
taskfile requested to execute in ADMA mode, since that requires accessing
the shadow registers.  We also still need to override tf_read since libata
will read the result taskfile on a command failure, and we need to go into
port register mode before allowing this.
Signed-off-by: NRobert Hancock <hancockr@shaw.ca>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

It tries to spot when the slave is a mirror of the master and to fix up
problems that causes.

I've got two confirmations so far that this plus the "can fail set_xfer" patch
work for folks who had problems before.  Also if you are unfortunate enough to
be running something like HAL then it'll automount the same disk twice for you
and corrupt it without the fix (aint that nice...)

Tested (successfully) by Komuro <komurojun-mbn@nifty.com>.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

drivers/scsi/ipr.c: In function '__ipr_eh_dev_reset':
drivers/scsi/ipr.c:3865: warning: passing argument 4 of 'ata_do_eh' from incompatible pointer type

Cc: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

There was a rare report where SB600 reported SERR_INTERNAL and SRST
couldn't get it out of the failure mode.  Hardreset on SERR_INTERNAL.
As the problem is intermittent, whether this fixes the problem or not
hasn't been verified yet, but hardresetting the channel on internal
error is a good idea anyway.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch adds much needed error reason decoding and
reporting to sata_promise. It's simplistic but should
log all relevant error info the controller provides.
Signed-off-by: NMikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch changes sata_promise so that the PATA ports
on TX2plus chips are bound to the pdc_pata_ops structure.
This means that operations called from the SATA ops
structures don't need any SATA-vs-PATA tests any more.
Instead, operations that depend on a port being SATA or
PATA are separated into different procedures.

* pdc_cable_type() is split into a PATA version and a
  SATA version
* pdc_error_handler() is split into a PATA version and a
  SATA version, that both call a common version after
  setting up the `hardreset' function pointer
* pdc_old_check_atapi_dma() is now only used for SATAI
  ports, so is renamed to pdc_old_sata_check_atapi_dma()
  and simplified
* pdc_sata_scr_{read,write}() are now only used for SATA
  ports, so their is-not-SATA tests are removed
* pdc_port_start() is split into three procedures: a wrapper
  which performs the ->ops adjustment on TX2plus PATA ports,
  a procedure with the common code, and a procedure with
  the SATA-specific code (this bit might be cleaned up by
  Tejun's new init model)

Tested on 20619, 20575, and 20775 chips.
Signed-off-by: NMikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The recent change which moved cable detection from
pdc_pre_reset() to the new ->cable_detect hook only
added the hook for SATAII chips, leaving SATAI chips
and the 20619 without the hook. Fixed by this patch.
Signed-off-by: NMikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Both old-IDE and libata should be able handle all controllers and
devices found using normal resource reservation methods.

This eliminates the awful, low-performing split-driver configuration
where old-IDE drove the PATA portion of a PCI device, in PIO-only mode,
and libata drove the SATA portion of the /same/ PCI device, in DMA mode.
Typically vendors would ship SATA hard drive / PATA optical
configuration, which would lend itself to slow (PIO-only) CD-ROM
performance.

For Intel users running in combined mode, it is now wholly dependent on
your driver choice (potentially link order, if you compile both drivers
in) whether old-IDE or libata will drive your hardware.

In either case, you will get full performance from both SATA and PATA
ports now, without having to pass a kernel command line parameter.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The previous commit erroneously noted that the !IORDY filter was turned
on.  No true, that change was split out into this commit.

Originally authored and signed-off-by Alan Cox.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NJeff Garzik <jeff@garzik.org>

With Tejun having added adev->ap some time ago we can get rid of the
almost unused port being passed to mode filters. And while we are
doing filters, lets turn on the !IORDY filter as well.
Signed-off-by: NAlan Cox <alan@redhat.com>

With some hand massaging from
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Now that we have ata_do_set_mode() available for drivers to use we don't
actually need ->post_set_mode() as the driver can wrap set_mode nicely
and do stuff before or after (eg PCMCIA needs before), so we can kill off
a method in all the structs

While I was at it I added kernel-doc to the function involved.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This alone isn't sufficient to save the universe from prehistoric disks
and controllers but it is a first important step. Split off a separate
function to provide a mode filter when controller iordy is not available.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This splits set_mode into do_set_mode and the wrapper so that a driver can
call the standard method inside its own.  This in theory also obsoletes
->post_set_mode().
Signed-off-by: NAlan Cox <alan@redhat.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Drag pata_hpt37x kicking and screaming in the direction of
drivers/ide/pci/hpt366.c and all the work that Sergei has been doing
there. Plenty left to be done but this is a good snapshot for folks to
work on and to review
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Implement pcim_iounmap_regions() - the opposite of
pcim_iomap_regions().
Signed-off-by: NTejun heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Roll-up of ->cable_detect feature addition patches, authored and
signed-off-by Alan Cox.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>